Instruction/ maintenance manual of the product TRINITRON KV-J51PF2S Sony
Go to page of 46
1 2 3 4 6 7 8 9 ÷ 0 5 TV MODEL COMMANDER DEST . CHASSIS NO . KV -J14P2S RM-869 Indonesia SCC-U10D-A KV -J51PF2S RM-869 Indonesia SCC-U10E-A SERVICE MANUAL MODEL COMMANDER DEST .
– 2 – KV -J14P2S/J51PF2S RM-869 SPECIFICA TIONS CAUTION SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE MET AL CHASSIS, CR T SHIELD , OR CARBON P AINTED ON THE CRT , AFTER REMO VING THE ANODE.
– 3 – KV -J14P2S/J51PF2S RM-869 TABLE OF CONTENTS 1. GENERAL .................................................................... 4 2. DISASSEMBL Y 2-1. Rear Cover Removal ............................................ 9 2-2. Speaker Removal .......
– 4 – KV -J14P2S/J51PF2S RM-869 SECTION 1 GENERAL The operating instructions mentioned here are partial abstracts from the Operating Instructions Manual.
– 5 – KV -J14P2S/J51PF2S RM-869 5 Getting Started -EN p KV-J14P2S p KV-J51PF2S to antenna output Rear of TV to antenna socket ≥ Ú … D to video and audio outputs VCR R L(MONO) ≥ .
– 6 – KV -J14P2S/J51PF2S RM-869 Getting Started 6 -EN Presetting channels Presetting channels automatically 1 Press SELECT on the remote commander or the TV until “AUTO PROGRAM” appears on the screen. 2 Press +/– on the remote commander or .
– 7 – KV -J14P2S/J51PF2S RM-869 Operations 8 -EN W atching the TV 1 Press U to turn on the TV. When the TV is turned on in standby mode, press u on the remote commander. 2 Select the TV program you want to watch. To select a program position directly Press the number button.
– 8 – KV -J14P2S/J51PF2S RM-869 11 Operations -EN T roubleshooting Additional Information If you have any problems, read this manual again and check the countermeasure for each of the symptoms listed below. If the problem persists after trying the methods below, contact your nearest authorized service center or dealer.
– 9 – KV -J14P2S/J51PF2S RM-869 2-1. REAR CO VER REMOV AL 2-2. SPEAKER REMO V AL 2-4. SER VICE POSITION SECTION 2 DISASSEMBL Y 1 Four screws ( + BVTP 4 × 16) 2 Two screws ( + BVTP 4 × 16) 1 Two screws ( + BVTP 4 × 16) 2 Speaker block assy A board Lever Lever A board 2-3.
– 10 – KV -J14P2S/J51PF2S RM-869 2-5. REPLA CEMENT OF P ARTS For replacement of the Multi Button and Light Guide, cut the welded portions from them, exchange with the ne w parts, and fix them with scre ws (+BVTP) respectively . 2-5-1. REPLA CEMENT OF MUL TI BUTT ON 2-5-2.
– 11 – KV -J14P2S/J51PF2S RM-869 c Anode button 2-7. PICTURE TUBE REMO V AL 2 Using a thumb press down, then pull up the rubber cap firmly in the direction indicated by the arrow b .
– 12 – KV -J14P2S/J51PF2S RM-869 Deflection yoke positioning corrects these areas. Purity control corrects this area. Disk magnets or rotatable disk magnets correct these areas (a-d). b c a d ba c d • The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
– 13 – KV -J14P2S/J51PF2S RM-869 3-2. CONVERGENCE Preparation : • Before starting this adjustment, adjust the focus, horizontal size, and vertical size. • Minimize the brightness setting. • Provide dot pattern. (1) Horizontal and V ertical Static Con ver gence 1.
– 14 – KV -J14P2S/J51PF2S RM-869 B G R B G R R G B R G B R G B R G B B G R B G R R G B B G R B G R R G B 3. Move the deflection yoke as shown in the figure below and optimize the con ver gence. 4. Tighten the deflection yok e scre ws. 5. Install the deflection yoke spacer .
– 15 – KV -J14P2S/J51PF2S RM-869 3-3. FOCUS ADJUSTMENT Adjust FOCUS control on the C board (R V703) for the best focus. b. METHOD OF CANCELLATION FROM SERVICE MODE Set the standby condition (Press POWER button on the commander) and then press POWER button again, hereupon it becomes TV mode.
– 16 – KV -J14P2S/J51PF2S RM-869 SECTION 4 SELF DIAGNOSIS FUNCTION If no acknowledgement is returned from a device which is turned "ON", the device has a problem. In this case, one of the LED's responding to the problem device will flicker a defined number of times.
– 17 – KV -J14P2S/J51PF2S RM-869 Entering service mode W ith the unit on standby ↓ DISPLA Y ↓ 5 ↓ VOL (+) ↓ POWER The operation sequence puts the unit into service mode. SECTION 5 CIRCUIT ADJUSTMENTS 5-1. ADJUSTMENTS WITH COMMANDER Service adjustments are made with the RM-869 that comes with this unit.
– 18 – KV -J14P2S/J51PF2S RM-869 WRITE WRITE GREEN 0C VSF 058S SERVICE 50 50 50 GREEN 0C VSF 058S Adjusted with [3] and [6] buttons Written with [MUTING] Write executed with [0] GREEN The WRITE display will change back to SERVICE. 0C VSF 058S 5-2.
– 19 – KV -J14P2S/J51PF2S RM-869 Adjustment Item T able (KV -J14P2S) Device Item Adj. No . Item 00 HSF 00–3F 50: 2C 60: 33 H Shift TD A8375 01 HSZ 00–3F 50: 35 60: 35 H Size TD A8375 02 P AP 0.
– 20 – KV -J14P2S/J51PF2S RM-869 Device Item Adj. No . Item Data Range Initial Data Note f or Diff erent Data Function 37 OFM 00–0F 00 RGB Output Time (AC OFF) Other Control 38 OSH 00–3F 0A OSD H POSITION Other Control 39 DSK 00–01 00 D/K Stereo enab le/disable TDA8375 3A MUT 00–01 00 Muting on/off at No .
– 21 – KV -J14P2S/J51PF2S RM-869 Option Note Item No. 13 VPX Item HCO EV G SBL PRD – – – VID Initial data 0 0 0 0 0 0 0 0 HCO EHT T racking Mode 1 = on V and E–W . 0 = only on V EV G Enable V er tical Guard 1 = enable. 0 = disable SBL Service Blanking 1 = active.
– 22 – KV -J14P2S/J51PF2S RM-869 Adjustment Item T able (KV -J51PF2S) Data range Initial data Standard data Note De vice Item Adjustment number Item 00 HSF 00–3F 5 0 : 2 C 60: 33 RGB50: 31 RGB60.
– 23 – KV -J14P2S/J51PF2S RM-869 Data range Initial data Standard data Note De vice Item Adjustment number Item 3A DKS 00–01 01 D/K Stereo enab le/disable Other Control 3B MUT 00–01 00 Muting on/off at No .
– 24 – KV -J14P2S/J51PF2S RM-869 Item No T op A V Input A VMUT B/G I D/K M KV -J14P2S 0011 1000 KV -J51PF2S 0011 1000 No. 49 OP0 Item No Nicam – H DEV 1 V -Cur ve XT AL SECAM 2nd Select Language KV -J14P2S 0000 1101 KV -J51PF2S 0000 1101 No. 4A OP1 Item – – No.
– 25 – KV -J14P2S/J51PF2S RM-869 5-4. PICTURE DIST ORTION ADJUSTMENT Item Number 00 – 08 00 HSF (H SHIFT) 01 HSZ (H SIZE) 02 P AP (PIN AMPLITUDE) 03 CNP (CORNER PIN) 04 TL T (TIL T) 05 VSL (V SLOPE) 06 V AP (V AMPLITUDE) 07 SCR (S CORRECTION) 08 VSF (V SHIFT) 5-3.
– 26 – KV -J14P2S/J51PF2S RM-869 MEMO.
– 28 – – 29 – – 27 – KV -J14P2S/J51PF2S RM-869 KV-J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 – 30 – SECTION 6 DIAGRAMS 6-1.
– 32 – – 33 – – 34 – – 31 – KV-J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 KV-J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 A 1234 5678 9 1 0 1 1 1 2 13 B C D E F G H I J A BOARD.
A 1234 5678 9 1 0 1 1 1 2 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 B C D E F G H I J K L M N O – 36 – – 37 – – 35 – – 38 – (1) Schematic Diagram of A Board 1 11 FV 10 9 8 .
– 40 – – 41 – – 39 – – 42 – A 1234 5678 9 1 0 1 1 1 2 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 B C D E F G H I J K L M N O (2) Schematic Diagram of A Board Schematic diagr.
– 44 – – 45 – – 43 – – 46 – A 1234 5678 9 1 0 1 1 1 2 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 B C D E F G H I J (3) Schematic Diagrams of C and VM Boards (KV-J14P2S) H KG.
– 48 – – 49 – – 47 – – 50 – KV-J14P2S/J51PF2S RM-869 KV-J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 Schematic diagrams ? C VM boards Schematic diagram A (.
KV -J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 TRANSISTOR IC DIODE 6-4. SEMICONDUCTORS D4SB60L CATHODE ANODE DINL20-T A EL1Z EGP20G GP08D NNCD8.2A-T1 NNCD9.1A-T1 RGP02-17EL-6433 CATHODE ANODE ERC06-15S RN4Z RU4AM-T4 S3L20UF4 RD9.1ES-L2 CATHODE ANODE RD2.
KV -J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 NOTE: • Items with no part number and no description are not stocked because they are seldom required f or routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column.
KV -J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 REF .NO. P AR T NO. DESCRIPTION REMARK 1 4-062-884-61 DOOR, CONTROL 2 X-4037-823-1 BEZNET ASSY 1, 3-7 3 4-047-464-01 CA TCHER, PUSH 4 4-055-546-21 B.
KV -J14P2S/J51PF2S RM-869 KV -J14P2S/J51PF2S RM-869 SECTION 8 ELECTRICAL P ARTS LIST NOTE: The components identified by shading and mark ! are critical for safety . Replace only with part number specified. When indicating parts by reference number , please include the board name.
– 59 – The components identified by shading and mark ! are cr itical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF . NO. P ART NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK C623 1-126-934-11 ELECT 220UF 20.
– 60 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF . NO. P ART NO. DESCRIPTION REMARK D308 8-719-109-54 DIODE RD2.
– 61 – The components identified by shading and mark ! are cr itical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF . NO. P ART NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK L406 1-410-507-11 INDUCTOR 6.
– 62 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified.
– 63 – The components identified by shading and mark ! are cr itical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF .
– 64 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF . NO. P ART NO. DESCRIPTION REMARK R895 1-216-349-00 MET AL OXIDE 1 5 % 1 W R898 1-249-421-11 CARBON 2.
– 65 – The components identified by shading and mark ! are cr itical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF .
– 66 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF . NO. P ART NO. DESCRIPTION REMARK R707 1-260-105-11 CARBON 3.
– 67 – The components identified by shading and mark ! are cr itical for saf ety . Replace only with part number specified. KV -J14P2S/J51PF2S RM-869 REF . NO. P ART NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK C1770 1-104-999-11 MYLAR 0.
– 68 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified.
An important point after buying a device Sony TRINITRON KV-J51PF2S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony TRINITRON KV-J51PF2S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony TRINITRON KV-J51PF2S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony TRINITRON KV-J51PF2S you will learn all the available features of the product, as well as information on its operation. The information that you get Sony TRINITRON KV-J51PF2S will certainly help you make a decision on the purchase.
If you already are a holder of Sony TRINITRON KV-J51PF2S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony TRINITRON KV-J51PF2S.
However, one of the most important roles played by the user manual is to help in solving problems with Sony TRINITRON KV-J51PF2S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony TRINITRON KV-J51PF2S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
