Instruction/ maintenance manual of the product SU-30HX1 Sony
Go to page of 16
1 INSTRUCTIONS The SU-30HX1 TV stand is designed for use only with Son y 30-inch TV set listed to the right. INSTRUCCIONES Este sopor te del televisor SU-30HX1 ha sido diseñado par a ser usado solamente con el televisor Son y de 76 cm (30 pulg.) notado a la derecha.
2 3 FRONT PILLAR (RIGHT) PILAR FRONT AL (DERECHO) PI LI ER AV AN T ( DR O IT ) FRONT PILLAR (LEFT) PILAR FRONT AL (IZQUIERDO) PI LI ER AV AN T ( GAUC H E ) Item Artículo Réf.
2 3 NO TES ON ASSEMBL Y Y ou will need a medium size Phillips head scre wdriver . Assemble the stand only by the method sho wn in this instruction sheet. Assemble the stand near the location where the stand will be used. The circled letters in the illustrations are the same as those in the “P ARTS LIST”.
4 5 2 3 WHEN TIGHTENING THE CAPNUT SCREW D , PLEASE USE A PHILLIPS HEAD SCREWDRIVER. DO NO T USE AN ELECTRIC SCREW DRIVER. CU ADO APRIETE EL T ORNILLO D , POR F A VOR USE UN DESARMADOR DE CR UZ. NO UTILIZE UN DESARMADOR ELECTRICO . LORS DU SERRAGE DE LA VIS ACR OU BORGNE D , UTILISER UN T OURNEVIS À TÊTE CR UCIFORME.
4 5 CA UTION: STEEL BRIDGE F MA Y HA VE SHARP EDGES. PLEASE HANDLE WITH CARE WHEN INST ALLING TO ST AND PILLARS . PRECA UCION: EL PUENTE METÁLICO F PUEDE TENER BORDES AFILADOS. SE DEBE MANIPULAR CON CUIDADO AL INST ALARLO EN LOS PILARES FRONT ALES. A TTENTION - LE TRA VERSE EN ACIER F PEUT A VOIR DES BORDS TRANCHANTS.
F 1 2 6 5 6 7 1 2 Inser t steel bridge F into slots as shown. Baje el puente metálico F a las plataformas como muestra la gura. Insérer le suppor t en acier F dans les fentes , comme montré. Inser t screw G x 2 from bac k and tighten as shown. Inser te el tornillo G x 2 desde la par te de atrás y apriete con un desar mador .
Hold by marked ( ) locations when moving TV stand. Sostenga de las locaciones marcadas ( ) cuando mue va el sopor te de televisor . Soutenir aux endroits marqués ( ) lorsque vous de déplacez le meuble de télévision.
8 9 PLEASE CHOOSE EITHER LOCA TION BASED ON SHELF POSITION ON STEP 4 . ELIJA EL SITIO DESEADO EN BASE A LA POSICION DE LA REPISA EN EL P ASO 4 . CHOISIR L ’EMPLA CEMENT EN FONCTION DE LA POSITION DE L ’ÉT A GÈRE À L ’ÉT APE 4 .
8 9 FOR LO WER GLASS SHELF ASSEMBL Y P ARA ENSAMBLAR EL DE LA REPISA POSICION INFERIOR POUR L ’ÉT A GÈRE EN VERRE INFÉRIEURE POSITION 2 POSICION 2 POSITION 2 FOR UPPER GLASS SHELF ASSEMBL Y P ARA.
10 11 6 USE VINYL SEALS K TO CO VER THE 4 HOLES NOT IN USE. KEEP REMAINING SEALS FOR FUTURE USE. UTILIZE LOS SELLOS DE VINIL K P ARA T AP AR LOS 4 HO Y OS QUE NO SE UTILIZAN. GU ARDE LOS SELLOS SOBRANTES P ARA SU USO EN EL FUTURO . VEUILLEZ APPOSER LES SCELLES EN VINYLE K POUR COUVRIR LES 4 TROUS NON UTILISES.
10 11 KD-30XS955 KV -30HS420 8 INST ALLING THE TV INST ALACION DEL TELEVISOR INST ALLA TION DU TÉLÉVISEUR Carrying the TV / T ransportando la TV / T ranspor t de la TV This TV has two holding points (marked ) on each side . The TV is front heavy , please handle with care.
12 13 NO TE: FOLLOWING STEP 9 WILL INCREASE THE ST ABILITY OF THE FINAL TELEVISION/ST AND UNIT . NO T A: EL SIGUIENTE P ASO 9 INCREMENT ARÁ LA EST ABILID AD DEL CONJUNT O TELEVISOR/SOPOR TE. NO TE: L ’ÉT APE 9 CI-DESSOUS A UGMENTE LA ST ABILITÉ DE L ’ENSEMBLE TÉLÉVISEUR ET MEUBLE.
12 13 10 Inser t bottom 2 tabs rst. Then s wing top por tion inwards. Inser te primero las 2 pestañas inferiores. Luego gire la par te superior hacia adentro . Introduisez les 2 pattes inférieures en premier et faites ensuite basculer la par tie supérieure vers l’intérieur .
14 15 Unit : mm (inches) Unidad : mm (pulgadas) Unité : mm (pouces) CARR YING CAP ACITY OF EA CH SHELF RESISTENCIA DE CAD A REPISA CAP A CITÉ DE RÉSIST ANCE DES ÉT A GÈRES SONY ELECTRONICS INC . PRINTED IN USA SONY ELECTRONICS INC . IMPRESO EN EUA SONY ELECTRONICS INC .
14 15 FOR RESIDENTS OF CANAD A POUR LES RÉSIDENTS DU CANAD A P ARA RESIDENTES DE CANADÁ SU-30HX1 Please e xamine all packaging materials bef ore discarding.
S LIMITED W ARRANTY Sony Electronics Inc. (“Sony”) warrants this product against defects in material or workmanship, subject to any conditions set forth as follows: 1. This warranty is expressly limited to the replacement of Sony TV Stand parts and components.
An important point after buying a device Sony SU-30HX1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony SU-30HX1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony SU-30HX1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony SU-30HX1 you will learn all the available features of the product, as well as information on its operation. The information that you get Sony SU-30HX1 will certainly help you make a decision on the purchase.
If you already are a holder of Sony SU-30HX1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony SU-30HX1.
However, one of the most important roles played by the user manual is to help in solving problems with Sony SU-30HX1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony SU-30HX1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
