




QUICK REFERENCE GUIDE TO FREQUENTLY USED FEATURES
These are the basic instructions for the most frequently used telephone system and voice mail features. For detailed information on these and other features, refer to the complete instructions in the User Guide.
To answer an intercom call that comes in through your speakerphone:
EITHER, Respond handsfree. OR, Lift the handset for privacy.
To answer a ringing (non-handsfree) intercom call:
EITHER, Lift the handset for privacy. OR, Press (Speaker) or to respond handsfree. OR, Press the flashing (Intercom) button.
P LACING AN O UTSIDE C ALL
Dial to automatically place a call to the system’s programmed emer- gency number (usually 911). You do not have to select an outside line first.
If using an IP phone, consult your system administrator and your local Inter- Tel servicing company for important information about dialing emergency services from your phone before you begin using it.
© Inter-Tel, Inc. October 2003 printed in US Part no. 835.2616-3

EITHER, Lift the handset. OR, Press . OR, Press the flashing button.
R EDIALING AN O UTSIDE N UMBER
Select a line. Then press or dial . The number is automatically dialed.
P LACING A C ALL ON H OLD
Press (Hold) and hang up or place another call.
To return to the call, lift the handset. Then press or the flashing button.
If you hear a “call waiting” tone through your handset and/or you see a flashing lamp, end your current call or place it on hold. Then press , , or the flashing button.
P AGING

Press . (Six-line display model users must then press the FWD OFF menu button.)
P LACING C ONFERENCE C ALLS
C HANGING V OLUME L EVELS
Press the (high) or (low) end of the Volume button to change the volume level. To save your change: EITHER, Press both ends of the Volume button at the same time. OR, Press the middle of the Volume button.
If your button is lit and you have a message from voice mail:
#

If your button is not lit, access your mailbox as follows:


*Some feature codes may not apply to your phone. For a list of feature codes specific to your phone, consult the user guide.
Below is a summary of the options you can

All Calls 355 If No Answer 356 If Busy 357 If No Answer/Busy 358
dent on the software version.
To turn on Call Forward:
To turn off Call Forward:
phone number.
Enter and hang up.
To turn on Do-Not-Disturb:
To turn off Do-Not-Disturb:
chart on the next page).
Remote Feature Access allows you to place
your phone in Do-Not-Disturb mode or forward
calls, either from another phone or through a
If you do not hear a tone after each step, or if
you hear repeating tones, you have made a
mistake or the feature is restricted. Start over.
OR, use any phone on the system.
To use Remote Feature Access:
required, enter your password.
To change Station Password:
tion and press .
special dial-up line.



Your new Model 8600 Phone provides access to several features, each of which is described in this guide. The About This Guide section below lists the different sec- tions in this user guide and describes the type of information you can find there. If you need to access information quickly, refer to the Quick Reference Guide attached to the front of this guide. You can also tear out the pocket guide to keep as a handy reference for features you are likely to use while away from the office (Remote Fea- ture Access and Voice Mail).
This guide contains instructions for using the Model 8600 Phone in Axxess IP mode on the Inter-Tel® Axxess® telephone and voice mail systems. To help you find infor- mation quickly, this guide is divided into four separate sections, as indicated by the tabs.
These sections include the following:
In addition, this guide contains a list of default feature codes (see page 65), an index (see page 69), and a voice mail flow chart (see page 73) for easy reference.

Your Model 8600 Phone is equipped with a hearing aid-compatible handset, a mes- sage indicator lamp, an internal speaker, and two basic types of buttons.


The feature buttons are designed to automate some of the commonly used functions, such as dialing an outside number. Each of these is described in the table below.

Press the low or high end of the Volume button Adjust volume during a call. 36
Press (International Hold Symbol) Put a call on hold. 18
Press and dial the destination number Transfer a call. 20
Press and dial the numbers you would like to add to the conference
Press and dial the destination number Forward calls to the specified number.
In addition to the buttons identified in the preceding table, your phone has a Special button ( ). Depending on how your telephone system is configured, you may need to press this button before you dial a feature code. Consult your system administrator if you have questions about how your system is configured.

The message indicator lamp (located at the top, right-hand corner of the phone) shows the same indications as the button. This indicator flashes whenever there is a waiting message. Power Requirements
The Model 8600 Phone requires either an individual power supply unit or a central- ized power source to power the phone. Check with your system administrator about the specific power requirements for your phone.
Before connecting a power supply unit, make sure it is compatible with your phone. The following individual power supply units are compatible with the Model 8600 Phone:
It is recommended that you plug your phone’s individual power supply unit into an Uninterruptible Power Supply (UPS). If your phone’s power supply unit is not plugged into a UPS and the power fails, the current phone call will be dropped.
Your system may be configured to use a centralized power source (power over Ether- net) rather than an individual power supply unit. Your system administrator will explain how to connect your phone to the centralized power source. If your phone uses power over Ethernet, do not connect an individual power supply unit to the phone.

Voice mail is an application that is part of the Inter-Tel Voice Processor. With the voice mail application, you and other callers can send and receive recorded messages from any station, touchtone telephone, or other device on the phone system. To use this and other features, each user is assigned a “voice mailbox,” which usually corre- sponds to a valid extension number. You can, however, have an “unassociated” mail- box that does not correspond to an extension. Unassociated mailboxes are typically used for agents or other personnel who don’t have a permanent office.
With your voice mailbox, you can use personal or system greetings to let callers know if you are out of town, on a call, etc. (see page 12). If a caller reaches your voice mail- box, they can leave a message, hang up, or access an attendant.
In addition, the voice mail administrator can program the name for “group lists” of mailboxes. With these lists, you can send a message to a group of people by entering one number instead of everyone’s individual mailbox number.
Your Model 8600 Phone is compatible with the following Inter-Tel software:

Your Model 8600 Phone and the telephone system come equipped with many fea- tures. To help you understand what everything means, it is recommended that you read the following information before you use your phone:



Now that you know what your Model 8600 Phone can do, it’s time to start using it. In this section, you’ll learn how to make and receive calls, transfer calls, retrieve voice mail messages, and much more.
Your Model 8600 Phone has an adjustable base that allows you to tilt your phone to enhance the viewing angle.
To adjust the viewing angle of the phone:

To begin using your voice mailbox, you need to complete a few basic setup proce- dures to initialize your mailbox, customize your personal greetings, and record your voice mail directory name. See page 39 for additional voice mail options. Initializing Your Mailbox
One of the first things you should do is initialize your mailbox. This allows you to:
To initialize your mailbox:

# · # · #

You can store two different personal greetings in your voice mailbox: a primary and an alternate. You can then select which greeting you want played when a caller reaches your voice mailbox. Because the purpose of this greeting is to tell callers why they have reached your voice mailbox, you should include the following information:
The following are some sample greetings to help you plan your message:
To change your personal greeting:
#

Your recorded name is used to identify you in the voice mail directory and to verify your mailbox number when messages are addressed to you.
To change your directory name:
# · #

Making and receiving calls is the basic purpose of any phone. With your Model 8600 Phone, you can make/receive intercom and outside calls and make emergency calls.

Consult your system administrator and your local Inter-Tel servicing company for important information about dialing emergency services from your Model 8600 Phone before you begin using it.
Your extension number allows other people to place intercom calls to you, without dialing any extra codes. And, because every phone in your phone system is assigned an extension number, you can call other people in your system quickly and easily.
To place an intercom call:
1. Lift the handset and dial an extension number. 2. If your call goes through handsfree to a phone’s speaker, speak after your party answers. If you hear continuous ringing, wait for the call to be answered. The phone system allows you to place a non-handsfree call that will override hands- free mode on the extension you are calling. If you use the Ring Intercom Always fea- ture to always send non-handsfree calls, the called party must pick up the handset to answer the call.
To place a non-handsfree call that will ring at the other phone until answered: Press before dialing the extension number.
To program your phone to always send non-handsfree calls using the Ring Inter- com Always feature: With the handset in the cradle, dial .
#

If there is no answer or if the phone is busy when you place an intercom call, you can do any of the following: • To leave a station message: Press and then hang up.
Your phone can receive both intercom and non-handsfree intercom calls. If the hands- free feature is enabled on your phone, intercom calls are automatically answered. Non-handsfree intercom calls (see page 14) override the handsfree option.
If your handsfree feature is disabled, or if you receive a non-handsfree intercom call, you must pick up the handset or press a button to answer the call.
To enable or disable your phone’s handsfree answering feature: With the handset in the cradle, dial .
To receive an intercom call: If the handsfree feature is enabled, the call is automatically answered, but you must lift the handset to respond to the caller.
If the handsfree feature is disabled, you can press to answer a call, but you must lift the handset to respond to the caller.

To receive a non-handsfree intercom call: Lift the handset to respond to the caller.
To redirect a ringing call to another extension or to an outside number:
With outside calls, you can talk to people who aren’t members of your phone system. When you make an outside call, however, you must dial any area codes or long dis- tance digits that your telephone company requires.
To place an outside call:
Depending on how your system is programmed, you may be able to use one of the following methods to select an outgoing line, instead of dialing the Outgoing Call access code:
To request a callback (queue on to the line) if all outgoing lines are busy when you try to call out: When you hear busy signals, press and hang up. When the line is available, your phone rings.
To cancel the queue request before your phone rings: Press .

When dialing the number, you have the following options: • Use the voice mail directory. See page 53.
To receive an outside call: Lift the handset to respond to the caller.
To redirect a ringing call to another extension or to an outside number:
With the telephone system, you do not have to dial the Outgoing Call access code (default is ) to dial an emergency number.
To make an emergency call: Dial . A call is automatically placed to the preset emergency number.

Consult your system administrator and your local Inter-Tel servicing company for important information about dialing emergency services from your Model 8600 Phone before you begin using it.
If you receive a call while you are already on another call, you will hear a “call wait- ing” tone.
To respond to a waiting call: • To end the current call: Hang up. The waiting call rings in.

You can place calls on hold in one of two ways: individual or system.
To place a call on Individual Hold:

With the Conference feature, you can establish a conference call with up to three intercom and/or outside parties (four, including you).
To place a conference call:
CNF
CNF
a. Press . This leaves the conference parties connected.
b. Place a call to the party to be added to the conference.
c. Press twice to put yourself and the new party into the conference.

Although transferring calls is considered a basic function of a phone, your Model 8600 Phone has many advanced options for this feature. With your phone, you can transfer a call to another extension, voice mail, or even an outside line. To Another Extension

The Reverse Transfer (Call Pick Up) feature allows you to answer a call that is ring- ing or holding at another phone. For example, if the attendant transfers a call to you but you have stepped away from your phone, you can pick up the call using another phone.
To answer a call ringing or holding at another phone:

With the Forwarding feature, you can have calls follow you (e.g., forwarded to a cell phone), or you can redirect calls to a voice mail or other extension. Manual Call Forwarding
Manual call forwarding allows you to send incoming calls to another extension num- ber. You can even forward calls to outside numbers, if your phone is programmed to allow this.
To forward calls:
To cancel any call forward request: EITHER, Press and then .
OR, Dial any one of the feature codes listed above and then press .

Automatic System Forwarding allows your system administrator to route calls based on the type of call and the status of your telephone. Although you cannot program the path of a system forward, you can enable or disable this feature on your phone.
The Redirect Call feature allows you to forward any call that is ringing on your phone without having to answer the call.
To redirect a call to an extension number:
#

The redial feature allows you to redial the last outside number you dialed. Although most phones redial the last number dialed, your system administrator can program your phone to redial the last number saved.
To use the Last Number Dialed feature (if enabled): Lift the handset and dial . A line is selected automatically, and the number is dialed.
To use the Last Number Saved feature (if enabled): • To save the last number dialed: While the phone is idle or while listening to inter- com dial tone, dial .
With an electret headset, you can talk on the phone handsfree, without using your speaker and microphone.
To connect a headset:

The Group Listen feature allows you to transmit a conversation over the speaker while you use the handset or headset to continue speaking. This allows other people to hear the caller while the caller can only hear you.
To turn the group listen feature on or off during a call: Press and dial . You hear a confirmation tone (the other party does not hear this tone).
The mute feature allows you to mute the microphone in the handset so that you can hear the other party, but they cannot hear you. This feature does not put the party on hold.
To enable/disable the mute feature on your handset: Press and dial .

In today’s busy world, it’s almost guaranteed that you will call someone that is on another call, does not answer, or is in DND. But, with the button, you can let the other person know you called.
When you leave a message, you can:
To indicate that a message is waiting, the button and the message indicator lamp flash. Leaving Messages
To leave a station message while on an intercom call: Press and hang up.
To leave a voice mail message while on an intercom call: Press and wait for the message center to answer. To leave a silent message without placing an intercom call:
To retrieve a message (Message button and lamp are flashing): Lift the handset and press . A call is automatically placed to the phone or mes- sage center that left the message. (See the following section for information about entering your mailbox.)
To cancel a waiting message:
Press .

If you have a message waiting in your mailbox, you must access your voice mailbox to retrieve it.
TIP: Generally, pressing during any voice mail operation will advance you to the next step. For example, when leaving a voice mail message for another voice mail user, you can press to skip the person’s introductory message and proceed directly to the recording phase. Similarly, while listening to messages, you can press to skip the system-generated voice prompts and proceed directly to the playback phase. You can also press to cancel or return to the previous menu at any menu level.

When you access your mailbox, the system may play one of the following messages:
To access your mailbox:


Once you’ve accessed your mailbox, the system will tell you how many new and saved messages you have. You can then listen to messages, delete messages, save messages, etc.
To listen to messages:
#

— Press to leave a voice mail message for the caller.
If the caller had a mailbox number, it will ask you to verify the destina- tion by pressing .
If the number was not associated with a mailbox, it will ask you to enter a mailbox number.
If the message was from an outside caller, you cannot leave a voice mail message.
— Press to make a return call. Your call will be transferred automati- cally to the caller’s extension or telephone number, if available.
If the extension number is not available, you will have the option of leaving a voice mail message.
If the telephone number is not available, you cannot reply to the mes- sage.
# · 1 #

If you accidently delete a voice mail message, you can retrieve it within a specific time frame (programmed by your system administrator). Any retrieved messages are then restored to your saved-message queue. Messages that are not undeleted within the programmed time (up to 24 hours) are automatically erased.
To recover deleted messages:
— Press to replay the message.
— Press to reply to the message.
— Press to forward the message to another mailbox.
— Press to listen to the previous message.
— Press to play the message envelope.
— Press to listen to the next message.
— Press to recover the message.
— Press to purge the message from your mailbox.

To send a message:
— Press to mark the message “private.” (This prevents the recipient from forwarding it to other subscribers.)
— Press to mark the message “certified.” (When the recipient listens to the message, you will receive a receipt notice.)
— Press to mark the message “priority.” (This will place your message ahead of all other waiting messages in the receiving mailbox.)
— Press to cancel delivery options.
— Press to deliver the message. (If you want to mark the message certi- fied, private, and/or priority, you must do so before completing this step.) You may choose either of the following options:

You can cancel unretrieved messages that you have sent to individuals, but not mes- sages that you sent to group lists.
To cancel unheard messages:
#

If you are away from your desk, or if you do not want to be disturbed, you can use the DND feature. This halts all pages and calls to your phone, except recalls and direct ring-in calls. When other users call your phone, they hear a repeating signal of four fast tones and, if they have a display phone, see the DND message you have selected.
Your telephone system can have up to 20 different DND messages, each of which can be changed by the system administrator, installer, or programmer. Your trainer or sys- tem administrator will give you a list of the programmed DND messages. For conve- nience, you should update the following default list.

To enable DND:
DND

Never be late for a meeting again! With Reminder Messages, you can program your phone, up to 24 hours in advance, to alert you at a specified time. At the programmed time, the reminder message signals you with eight short tones. If you are on a call, you still hear the tones.
Your phone system can have up to 20 different reminder messages, each of which can be changed by the system administrator, installer, or programmer. Your trainer or sys- tem administrator will give you a list of reminder messages for your system. For con- venience, you should update the following default list.

To request a reminder message:
If your system is set for 12-hour format, press for AM or for PM.
To cancel all reminder message requests before they signal you: With the handset in the cradle, dial .
To clear a received reminder message: With the handset in the cradle, press .
# · #


Now that you’ve mastered the basics, it’s time to move on to the advanced features. In this section, you’ll learn how to program your phone, use directories, access your voice mailbox remotely, and perform various other functions. SETTING PREFERENCES
Your phone and voice mailbox are automatically set to specific defaults. You can, however, configure many of these settings at any time. Phone Configuration
Customizable features on your phone include changing volume levels, enabling back- ground music, selecting a ring tone, and others. Changing Volume Levels The system has eight volume settings: handset intercom, handset outside call, speak- erphone intercom, speakerphone outside call, background music, ringing, handset intercom dial tone, and speakerphone intercom dial tone.
To change a volume level: Press (the high end of the Volume button) to increase the volume. Press (the low end of the Volume button) to decrease the volume.
To save your change: EITHER, Press both ends of the Volume button.
OR, Press the middle of the Volume button.

The ability to change your ring tone is helpful in close-quartered environments. If your ring tone is unique, you can quickly identify when a call is ringing on your phone.
To select the type of ring tone for your phone:
If your telephone system is equipped with a music source, you can listen to music through your speaker.
To enable or disable background music: Dial .
Keymaps identify where feature buttons appear on your phone. While all phones are programmed with a standard keymap, some phones have alternate keymaps (ask your system administrator). If you have an alternate keymap, you can switch between the keymaps by dialing a specific feature code.
To switch between keymaps when your phone is idle: With the handset in the cradle, dial .
To switch between keymaps during a call: Press and dial .
#

The Automatic Call Answer feature determines whether or not you are automatically connected to a caller when you lift the handset. If this feature is enabled, you are auto- matically connected when you go off-hook. If it is disabled, you must first lift the handset and then press .
To enable/disable this feature for ringing outside calls: With the handset in the cradle, dial .
To enable/disable this feature for ringing (non-handsfree) intercom calls: With the handset in the cradle, dial .
When your phone system is installed, the system administrator can choose two of four different languages (American English, British English, Japanese, or Spanish) as the primary and secondary languages. You can then change the voice mail prompts on your phone by toggling between the primary and secondary languages. For example, if the system’s primary language is American English, and your phone is programmed for the primary language, all voice mail prompts are played in American English (unless changed, as outlined below). If the secondary language is Japanese, and your phone is programmed for the secondary language, all voice mail prompts are played in Japanese.
To change the assigned language for your phone: Dial to change between your system’s primary and secondary languages, as desired.
You can return your phone to default levels at any time. This feature returns volumes to default levels; cancels DND, manual call forwarding, background music, and queue requests; and restores handsfree mode, pages, hunt group calls, and system forward- ing all at once.
To return your phone to default: Dial .

Your voice mailbox contains personal options that allow you to customize voice mail functions. Before you change your voice mail options, you must first initialize your mailbox (see page 11).
Your password prevents unauthorized access to your mailbox.
To change your password:
When you receive a voice mail message, the voice mail system first plays an “enve- lope” that can include the time and date the message was left, the source of the mes- sage, and/or the message length. By default, the envelope contains all of this information, but you can change your envelope, as described below.
To change your message envelope:
# · # 3 · #

Depending on the transfer method you select, transferred calls from voice mail may be unannounced (as usual), or one of the following may occur:
To change your transfer method (if allowed):

With the Inter-Tel Voice Processor, callers can use your mailbox to send you a fax. To use this feature, you must specify the destination fax number.
To change your Fax Destination Number:
When more than one message is left in your voice mailbox, you can change the order in which you retrieve your messages, based on the date and time they were received.
To change the listening order of your messages:
# · #

With Remote Messaging, you can program the Voice Processor (voice mail) to call you when your mailbox receives new messages. Using a “cascade” (a series of up to nine telephone numbers), voice mail will call each number until it successfully con- nects to a device (e.g., pager, answering machine, etc.).
Because your mailbox can have a primary and an alternate cascade of numbers, you can program a cascade to be used during specific days and times. For example, if you want to be paged when you receive a message from 5-10 PM on weekdays, you can set up a primary cascade. If you also want to receive pages for messages marked “pri- ority” on the weekends, you could set your alternate cascade for all day on Saturdays and Sundays.

To set up remote messaging:

— To set up or change an extension or telephone number: Press . Then press for an extension number or press for an outside number. Then enter the number.
— To set up or change a pager number: Press . Then enter the number.
— To enable or disable the cascade level: Press . (You cannot enable the level until a notification number is programmed.)
— Press for Monday-Friday.
— Press for all days.
— Press to select individual days. You are prompted to press digits 1-7 which correspond to the days Sunday through Saturday.
#

Speed dialing allows you (and your system administrator) to store frequently dialed numbers for easy dialing. Each number is stored on your phone (Station Speed Dial) or in the phone system (System Speed Dial) and is identified by a location number. Once programmed, you can then quickly dial these numbers by entering a feature code and dialing the desired location number. Because the system supports both Sta- tion and System Speed-Dial numbers, you can have access to over 1000 stored num- bers. Station Speed Dial
You can program and use up to ten personal speed-dial numbers on your phone. In addition, if you have programmable feature buttons, you can program them as speed- dial buttons for one-touch dialing. To use a speed-dial button, you must:

To store a speed-dial number, use the Station Speed-Dial Programming feature code to program the number in a speed-dial location. Use the following table to list the numbers that you store in speed-dial locations 0-9.
0 5
1 6
2 7
3 8
4 9
To store a number in a speed-dial location:
1. With the handset in the cradle, dial . 2. Dial the speed-dial location (0-9) you want to program. 3. Dial the extension number or telephone number to be stored at the location you selected in step 2. If your number includes an asterisk, pound, a hookflash (a quick hang up and release), or a pause, press once for an asterisk, twice for a pound, three times for a hookflash, or four times for a pause. (Each pause or hookflash counts as one digit.)

To dial a Station Speed-Dial number: If necessary, select an outgoing line. Dial and then enter the desired Sta- tion Speed-Dial location number (0-9).
#

Your system administrator can store up to 1000 speed-dial numbers in System Speed- Dial locations 000-999.
To dial System Speed-Dial numbers:
If your telephone system is equipped with a Voice Processor (voice mail), you may have access to the Record-A-Call feature. If so, you can record an ongoing call as a mailbox message. You can then retrieve the message, just as you would any other mailbox message.
To use the Record-A-Call feature while on a call:
To turn off Record-A-Call: EITHER, Press and dial .
OR, Hang up.
#

The Paging feature allows you to make an announcement through phone speakers or external speakers (if your system is equipped with external paging equipment). To prevent announcements from transmitting through every phone in the system, this fea- ture uses page zones. Each zone contains a different combination of extensions and external paging equipment, and is programmed by your system administrator. Ask your trainer or system administrator how the zones are programmed, and list them below for your convenience.
0 5
1 6
2 7
3 8
4 9
You can enable or disable page receiving for your phone by using the Page Remove/ Replace feature code. If your phone is assigned to more than one page zone, all zones are removed or replaced at once (you cannot turn off individual zones).
To turn paging on and off for your phone: Dial . Making Pages
To make pages:

Certain telephone service companies may require a timed hookflash (a quick hang up and release).
To generate a hookflash while using a line: Press and dial .
Depending on how your system is programmed, some of your feature buttons may be “user-programmable.” If so, you can program them with any of the feature codes listed in the back of this user guide. In addition, you can combine the feature button and Station Speed-Dial functions to program a feature button to dial an outside num- ber.
To program a user-programmable feature button:

A button programmed as a Direct Station Selection/Busy Lamp Field (DSS/BLF) but- ton provides a way to dial the associated extension with one touch. In addition, if the button is equipped with a lamp, you can visually monitor the status of the associated extension.
To assign an extension to a DSS/BLF button:

Solidly lit The associated extension is busy, or the associated feature is enabled.
Flashing rapidly The extension has a call ringing in.
Fluttering continuously The extension is causing a STATION OFF-HOOK system alarm.

With the Secondary Extension Appearances feature, you can program various buttons on your phone to indicate the call activity at a different extension (primary phone). In addition to being able to see when a call is ringing, answered, or on hold, you can use your secondary extension button to answer a call that is ringing at the primary phone. Your phone may also be programmed to ring automatically when a given number of calls are waiting at the primary phone (ask your system administrator).
There are two possible types of secondary extension buttons: programmable and non- programmable. If you have a non-programmable secondary extension button, only the system administrator can change the associated extension. If you have a programma- ble button, you can change the extension, as described below.
To assign a primary phone to a secondary extension button (if enabled):
To transfer a call back to the extension after you have answered it on your phone:
#

If your telephone system is programmed to use the Station Message Detail Recording (SMDR) feature, you might be required to enter account codes when you place a call. These codes add information to phone record reports that the system will periodically print.
There are three types of account codes:
To enter an optional account code:
To disable the code: Dial and press .
3 9 1 #
# · #

If your voice mailbox is programmed correctly, you can screen calls that are trans- ferred from voice mail. This allows you to accept and/or refuse specific calls. Depending on the transfer method you use, calls from voice mail may be unan- nounced, announce only, or screened calls (see page 40 for details).
If your voice mailbox is programmed for screened calls, you have the following options when you receive a transfer:
#

Whenever voice mail asks you to enter a mailbox number, you can use the mailbox and extension number directories. You can also use these directories to leave a voice message with another user. The system finds the closest matching directory name based on your entry.
The mailbox and extension number directories can be used any time voice mail asks you to enter a mailbox number. To enter the name, use your dialpad buttons. The sys- tem then plays the closest matching directory name that corresponds to the entry.
To perform a directory search using your dialpad buttons: Press a single digit on your telephone dialpad for each letter or character entered. For example, dialpad button indicates ABC, button indicates DEF, etc. To enter “JONES,” you would press . Press for “Q”, for “Z”, and for punctuation marks.
5 6 6 3 7 7 9 1
To use the directory to leave a voice mail message:
# · # · #

If you are away from your desk and forgot to put your phone in DND, don’t worry. With the Remote Feature Access, you can place your phone in DND or forward calls from any other phone on the system. And, if you have a special dial-up line, you can access your phone features from an outside line. Remote Access Password
Before you use Remote Feature Access, you should program a password, as described below.
To change the password from your phone:


To access your phone from another phone:
a. Dial .
b. Enter the new password, followed by .
c. Enter the new password again for verification, followed by .
To turn on DND:
a. Dial .
b. Enter the message number (01-20) and enter the optional second-line message
text.
To turn off DND: Dial . To turn on Call Forward: a. Dial one of the following Call Forward feature codes.
All Calls
If No Answer
If Busy
If No Answer or Busy
b. Enter an extension number or enter an outside line access code followed by a
telephone number.
To turn off Call Forward: Dial .
# · # · #

Your telephone system may be programmed to support the Agent Help feature, which allows you to request help from a designated “Agent Help Extension” (usually your supervisor) during a call. When your request call rings at the Agent Help Extension, the supervisor can choose to join the call or reject the request.
If the Agent Help Extension is a digital phone, the phone’s microphone is automati- cally muted so that the supervisor cannot be heard unless he or she presses . If the Agent Help Extension is a single-line phone, however, the supervisor can be heard as soon as the conference is established. In either case, the supervisor can hear all other parties on the call.
To use the Agent Help feature while on a call:
If the Agent Help Extension rejects the call, you hear a confirmation tone.

Your system may be programmed with “hunt groups.” Hunt groups are groups of phones that share a common extension number in addition to having individual exten- sion numbers. This allows someone to call anyone in the group (using the common extension) or a specific member (using the individual extension). The members of these groups and the common extension(s) are programmed by your system adminis- trator. Hunt Group Calls Enabled/Disabled
If you are a member of a hunt group, you can enable or halt hunt group calls to your extension.
To turn on or off hunt group calls: Dial . ACD Hunt Groups
Some hunt groups use a special feature called Automatic Call Distribution (ACD) that distributes the hunt group calls equally among the available members. These hunt group members are referred to as “agents,” who log in to the ACD hunt group to receive calls and log out to halt ACD hunt group calls.
Calls are distributed through an ACD hunt group based on Agent IDs or extensions, as described below.

Agents can log in to and out of the ACD hunt group at any time. While logged in, the agent receives calls through the ACD hunt group. When the agent is logged out, calls to that ACD hunt group bypass the agent.
To log in to all of your ACD hunt groups at once using the ACD Agent Login/ Logout feature code: Lift the handset and dial and enter your Agent ID, if necessary. You will hear a login confirmation tone.
To log in to one or more hunt groups using the ACD Agent Login feature code:
# · #

When you log in to a group, you may be automatically connected to a call after you hear a short ring burst. If the ACD Agent ID Automatic Connect option is enabled for your hunt group and you are using a headset, you will be automatically connected. If this option is not enabled for your hunt group, the call will ring until you answer it or until it times out to another extension.
To log out of one or more ACD hunt group:
Each time you end an ACD hunt group call, a wrap-up timer is started. Until this timer expires, you will not receive another call through any ACD hunt group. You can, however, end the wrap-up session before this timer expires, as described below.
To terminate the ACD Agent wrap-up period before the timer expires:



Introduction 62
What the Administrators Can Do for You 62 Frequently Asked Questions (FAQs) 63
Default Feature Codes 65


If you want to know more about your phone and voice mail system, this is the section for you. With additional information and FAQs, you should be able to find answers to most of your questions.
The administrators are the people to whom you should turn if you have any problems with your phone and/or voice mail. They have access to advanced programming fea- tures and can reset certain settings associated with your phone.
The types of administrators that can help you with your phone/voice mail are as fol- lows:
— Setting the date and time
— Programming System Speed-Dial numbers
— Making database changes, such as programming usernames, toll restriction, DND messages, and extension numbers
— Recording a broadcast message that is sent to all mailboxes at once
— Performing mailbox maintenance (such as changing your password)
— Customizing voice mail prompts
If you are a system administrator or if you need additional information not available in this guide, refer to the Administrator’s Guide (part number 550.8001).

This section includes some of the most frequently asked questions. If you have prob- lems with your phone or voice mailbox, refer to this section before you contact your system administrator or your local Inter-Tel dealer.
Q1. How do I program System Speed-Dial numbers?
A1. Only your system administrator can program System Speed-Dial numbers. You can, however, program up to ten Station Speed-Dial numbers (see page 44).
Q2. Why can’t I make and receive calls using the speakerphone?
A2. Although the phone has an external speaker, it does not have an external microphone. Therefore you must use the handset to communicate with another party when you make and receive calls.
Q3. How can I retrieve messages if I do not know the password for my voice mail?
A3. Try using your extension number, which is your default password. Or, maybe you do not have a password, in which case pressing is all you need to do. If these options don’t work, contact your system administrator, who can change or erase the password for you. You can then retrieve your messages and reset the password, if desired (see page 39).
Q4. Why can’t I retrieve deleted messages?
A4. Voice mail may have erased your message. After a programmed amount of time has lapsed, up to 24 hours, voice mail automatically erases all deleted messages (see page 30). If you attempted to undelete a voice mail message within this time frame but you were still unsuccessful, your voice mail system may not have sufficient space programmed to store deleted messages.
Q5. How can I set the number of rings that are allowed before the call is sent to voice mail?
A5. Only your system administrator can change the number of rings.
Q6. Why can’t I hear dial tone when I pick up my handset?

A6. Your phone may be in headset mode. While on-hook, enter the Headset Off feature code ( ) or the Headset On/Off feature code ( ).
#

Q7. Why can’t I program a Station Speed-Dial number to the button I want?
A7. Your system administrator has programmed that button as a non-programmable but- ton. Because you cannot override system programming from your phone, you must choose another button.
Q8. Why can’t I use one of the features described in this guide?
A8. There are a few reasons why you might not be able to access the feature. Some possi- ble reasons include:
Q9. Why don’t the local phone company star codes (i.e.*82, *69, etc.) work when I use the Outgoing Call feature code ( by default) to call an outside number?
A9. Rather than pressing to access an outside line, you must dial a Select Line Group number before you can use the star codes. For example, if your system is using the default Select Line Group numbers, dial 92001 to access that line. Once you have dial tone, you can dial the star code and the number.
Q10. Why can’t I use the Agent Help or Record-A-Call features?
A10. If your phone is configured to use peer-to-peer (P2P) audio, you will not be able to use the Agent Help and Record-A-Call features when you are on a P2P call. To deter- mine if your phone is configured to use P2P audio, consult your system administrator.
Q11. If I need further assistance, how do I get technical support?
A11. First, contact your system administrator if you have a question that is not covered in this user guide. If you need further assistance, contact your local authorized Inter-Tel dealer. All Inter-Tel sales, service, and support are handled at the local level.

Use the blank spaces below to enter custom feature codes, if necessary.

EXTENSION NAME EXTENSION NUMBER NEW NUMBER

Phone Extensions 1000-1999 · Hunt Groups 2000-2299 · Attendant 0

FEATURE NAME FEATURE CODE NEW CODE
Account Code – Following Calls 391 Account Code – Optional 390 ACD Agent Log In 326 ACD Agent Log Out 327 ACD Agent Log In/Out 328 ACD Agent Wrap-Up Terminate 329 Agent Help Request 375 Agent Help Reject 376 Answer (Ringing Call) 351 Automatic Intercom Access On/Off 361 Automatic Line Access On/Off 360 Automatic Line Answer 350 Background Music On/Off 313 Call Forward All Calls 355 Call Forward If Busy 357 Call Forward If No Answer 356 Call Forward No Answer/Busy 358 Change Language 301 Conference 5 Default Station 394 Directory 307 Do-Not-Disturb 370 Do-Not-Disturb Cancel 371 Do-Not-Disturb On/Off 372 Do-Not-Disturb Override 373 Feature Button Default 395 Group Listen 312 Handsfree On/Off 319 Headset On 315 Headset Off 316 Headset On/Off 317 Hold – Individual 336 Hold – System 335 Hookflash 330 Hunt Group Remove 322 Hunt Group Replace 323 Hunt Group Remove/Replace 324 Message 365 Message – Cancel Message Left 366 Message – Cancel Message On Phone 368 Message – Silent 367 Microphone Mute On/Off 314 Page 7 Page Receive On/Off 325

GENERAL FEATURE CODES (CONTINUED)

Program Buttons 397 Program Station Password 392 Queue (Callback) Request 6 Record-A-Call 385 Redial 380 Redirect Call 331 Reminder Message 305 Reminder Message Cancel 306 Remote Programming 359 Reverse Transfer (Call Pick-Up) 4 Ring Intercom Always On/Off 377 Ring Tone Selection 398 Routing Off 304 Station Speed Dial 382 Station Speed-Dial Programming 383 System Forward Enable 352 System Forward Disable 353 System Forward On/Off 354 System Speed Dial 381 Switch Keymap 399 Transfer To Hold 346 Transfer To Ring 345


GETTING STARTED LEARNING MORE





ACESSING YOUR MAILBOX • EITHER, Press the Mes- sage button to respond to a message from voice mail. OR, Call the voice mail extension number, press
, and enter your mailbox number. • Enter your password and then . #

Part No. 550.8115 Issue 8.1 November 2003
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.