Instruction/ maintenance manual of the product 82S6XR0A0B Solid State Logic
Go to page of 8
Super -Analogue™ Outboar d X-Rack Mic Amp User ’s Guide This documentation package contains the User ’s Guide for your new X-Rack Mic Amp module. Depending on the age of your X-Rack, these pages may already be pr esent in your X-Rack Owner ’s Manual – please check to see if these pages match your Manual.
.
Page A-1 X-Rack Mic Amp Module A. The Mic Amp Module A.1 Connection The rear panel of the module carries the Mic (‘IN’) and Line input (‘LINE’) XLRs along with a single output (‘OUT’) XLR. The Line input and output operate at a nominal level of +4dBu although the gain of the Line input can be varied by a front panel control.
Page A-2 X-Rack Owner ’ s Manual A.2.3 HF/LF Section This section contains simple high and low pass filters as follows: HF (Low Pass): Frequency range 50kHz – 3kHz (–3dB point) Slope: 12dB/Octave LF (High Pass): Frequency range 30Hz – 600Hz (–3dB point) Slope: 18dB/Octave The two filters can be switched into circuit independently .
Page A-3 X-Rack Mic Amp Module A.3 Performance Specification The following pages contain audio performance specification figures for the X-Rack Mic Amp module. No other Solid State Logic products ar e covered by this document and the performance of other Solid State Logic products can not be inferr ed from the data contained her ein.
Page A-4 X-Rack Owner ’ s Manual A.2.4 Instrument Input Performance Un-balanced signal applied to Instrument Input and measur ed at Output. Pad switched out and Input Gain control set to +12dB (minimum).
Page A-5 X-Rack Mic Amp Module A.4 Calibration Information The X-Rack Mic Amp module is factory calibrated and should only need calibration if a potentiometer or other component has been replaced or if it is suspected that ther e is a problem with calibration.
Page A-6 X-Rack Owner ’ s Manual A.5 Connector Details A.6 Physical Specification * Depth: 200mm / 7.9 inches including front panel knobs, excluding connectors 275mm / 10.9 inches including front panel knobs and connectors Height: 171mm / 6.75 inches W idth: 35mm / 1.
An important point after buying a device Solid State Logic 82S6XR0A0B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Solid State Logic 82S6XR0A0B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Solid State Logic 82S6XR0A0B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Solid State Logic 82S6XR0A0B you will learn all the available features of the product, as well as information on its operation. The information that you get Solid State Logic 82S6XR0A0B will certainly help you make a decision on the purchase.
If you already are a holder of Solid State Logic 82S6XR0A0B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Solid State Logic 82S6XR0A0B.
However, one of the most important roles played by the user manual is to help in solving problems with Solid State Logic 82S6XR0A0B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Solid State Logic 82S6XR0A0B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
