Instruction/ maintenance manual of the product FSD-800 Soho
Go to page of 22
FSD-8080 User's Manual i SOHOConnect Series FSD-800 8-port 10/100Mbps Ethernet Switch.
SOHOConnect Series Trademarks Copyright PLANET T echnology Corp. 2000. PLANET is a registered trademark of PLANET T echnology Corp. All other trademarks belong to their respective owners.
FSD-800 User's Manual 1 Table of Contents CHAPTER 1 ............................................................................ 1 G ENERAL I NTRODUCTION ...................................................... 1 Checklist .........................
SOHOConnect Series 2 This page is intentionally left blank ..
FSD-800 User's Manual 1 Chapter 1 General Introduction Checklist Check the contents of your package for following parts: ♦ The Fast Ethernet Switch ♦ Power Cord ♦ User ’ s Manual If any o.
SOHOConnect Series 2 a network more efficiently than bridges or routers in most environments. In the following sections, the term “ Switch ” will represent Planet ’ s FSD-800, and “ switch ” for third part Ethernet switches.
FSD-800 User's Manual 3 connecting workgroup devices and desktops, companies no longer have to invest in expensive and inflexible switches engineered primarily for backbone implementations.
SOHOConnect Series 4 ♦ LED indicators for simple diagnostics and management ♦ Port#8 provides an extra port for MDI and MDI-X mode PC or hub Uplink.
Chapter 2 Hardware Description This section describes the hardware features of the Switch. For easier management and control of the Switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators.
SOHOConnect Series 6 LED indicators LED Function Color Description Power (PWR) Green This indicator lights green when the hub is receiving power , otherwise, it is off.
FSD-800 User's Manual 7 100V~240VAC 50~60Hz Figure 2. Rear Panel of FSD-800 Hardware Installation 1. Place the Switch on a smooth surface 2. Connect the output cord of power supply to the AC-jack. 3. Connect hub or PC to one port of the Switch using Category 3/4/5 UTP/STP cabling.
SOHOConnect Series 8 may initially seem to work, it will soon cause data loss. All kinds of hub/PC can connect to switch by using straight- through wires. The hub provides one additional RJ45 connector that is converted from port 1, labeled “ Uplink ” port.
FSD-800 User's Manual 9 Uplink Figure 3. 100Mbps File server to Hubs Connection 10Mbps Hub to 100Mbps Hub Plug one end of the Category 5 UTP Cable into one port of the Switch, and the other end of this cable into “ Uplink ” port of the 100Mbps Fast Ethernet Hub.
SOHOConnect Series 10 Switch Operation Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc.
FSD-800 User's Manual 11 located at different port from this packet comes in; the Ethernet Switch will forward this packet to the port where this destination address is located according to the information from address table.
SOHOConnect Series 12 cabling and adapters. Due to the learning function of the Ethernet switch, the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table. This information is subsequently used to filter packets whose destination address is on the same segment as the source address.
FSD-800 User's Manual 13 If attached device is: 100Base-TX port will set to: • 10Mbps, no auto-negotiation 10Mbps • 10Mbps, with auto-negotiation 10/20Mbps (10Base-T/Full-Duplex) • 100Mbps,.
SOHOConnect Series 14 This page is intentionally left blank ..
Chapter 3 Troubleshooting This chapter contains information to help you solve problems. If the Switch is not functioning properl y , make sure the Switch was set up according to instructions in this manual. The Link LED is not Lit Solution: Make sure the switch configuration is consistent with the connecting device Check the cable connections.
SOHOConnect Series 16 The address table may contain older information than of the address table of that node. Please power down to refresh the address information.
Appendix A Specifications: General (Ethernet) Standards: IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100 Base-TX Fast Ethernet ANSI/IEEE Std 802.3 N-way auto-negotiation IEEE 802.
SOHOConnect Series 18 General (Ethernet) Humidity 10% ~ 90% non-condensing Dimensions 251 x 118 x 37 mm EMI FCC Class A, CE Mark Class A Performance Transmission Method Store-and-forward Filtering Add.
An important point after buying a device Soho FSD-800 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Soho FSD-800 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Soho FSD-800 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Soho FSD-800 you will learn all the available features of the product, as well as information on its operation. The information that you get Soho FSD-800 will certainly help you make a decision on the purchase.
If you already are a holder of Soho FSD-800, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Soho FSD-800.
However, one of the most important roles played by the user manual is to help in solving problems with Soho FSD-800. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Soho FSD-800 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
