Instruction/ maintenance manual of the product RP2167517BVE Snapper
Go to page of 33
Safety Instructions & Operator's Manual for 21" STEEL DECK WALK MOWERS SERIES 17 MODELS R2167517BV RP2167517BV RP215517HC RP2167517B VE WRP216517BE MODEL NUMBER EXPLANATION MODEL DESIGNA.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons.
IMPORTANT SAFETY INSTRUCTIONS OPERATION 1. DO NOT put hands or feet near or under rotating parts. Keep clear of discharge area while engine is running. 2. STOP engine when crossing gravel drives, walks, or roads, and under any conditions where thrown objects might be a hazard.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 2 - 3 TABLE OF CONTENTS ...................................................................................................... 4 SECTION 1 - FAMILIARIZATION .
Section 1 - FAMILIARIZATION WHEEL DRIVE BLADE CONTROL CONTROL _ GROUNDSPEED CONTROL IGNITION KEY ROPE START HANDLE REAR HEIGHT ADJUSTMENT LATCH GRASS BAG ADAPTER FUEL FILLER CAP BRIGGS ENGINE SPEED CONTROL FAST SLOW OIL FILL CAP AND DIPSTICK ENGINE PRIMER HONDA ENGINE SPEED CONTROL CHOKE FAST SLOW FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened.
Section 2 -OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE (Choke Models) 1. Move fuel shut off valve to the "ON" position. See Figure 2.5. NOTE: Stop the engine (and blade) by releasing the blade control. FIGURE 2.
Section 2 -OPERATING INSTRUCTIONS 2.4 HANDLE HEIGHT ADJUSTMENT 2.5 The height of the mower handle can be adjusted as follows: 1. Loosen the lower nuts on each lower handle as shown in Figure 2.8. LOWER HANDLE /J // HIGHER LOWER LOOSEN LOWER NUTS ON EACH LOWER HANDLE FIGURE 2.
Section 2 -OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 2 -OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 2 -OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 3- MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.
Section 3- MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS j_ WARNING _, DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS 4.5. BATTERY SERVICE 4.5.1. NEW BATTERY PREPARATION 1. Remove battery from carton. 2. Place battery in a well ventilated area on a level non-concrete surface. 3. Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level.
PROBLEM Engine Will Not Start Using Recoil Starter Engine Stalls or Stops After Running Engine Loses Power Excessive Vibration Mower Will Not Move Loss Of Traction (Self-Propelled Models) Cutting Grass Improperly Poor Grass Discharge Oil Leaking TROUBLESHOOTING PROBABLE CAUSE 1.
SERVICE SCHEDULE ITEM Engine Oil SERVICE PERFORMED REF. Check Oil Level Page 6 EACH 5 25 USE HRS HRS X 5O HRS 100 HRS Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre-Cleaner Air Cl.
3 YEAR LIMITED WARRANTY For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of c.
PRIMARY MAINTENANCE ® vs.DIRT I an illustration of how dirt can ge your engine & how reasonable maintenance can protect it! Snapper uses the best avail- able engines and components in their products in order to provide long, satisfactory service.
PRIMARY MAINTENANCE gulp about 12 gallons of air for every gallon of used. Because of its working environ- ment, the air avaUable to your Snapper engine Is " heavily saturated with air- borne dirt particles. __Knowing that dirt will quickly ruin an engine, .
PRIMARY MAINTENANCE Generally, wash foam-type filters In a dishwashlng detergent and water solution. Rinse and wring dry, then saturate with oil and squeeze out excess. Failure to re-oil this type filter will ruin the engine. Clean paper elements by tapping lightly.
PRIMARY MAINTENANCE On 4-cyle engines with an oll level plug, don't be fooled into thinking the engine has sufficient lubricating oii if you can see "some" oil in the opening - the level should always be brought up to the point of at the top of the fill hole.
SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper purchase) Model Number Serial Number Date of Purchase Retailer Retailer's Phone Number It is very important that you register your purchase with Snapper to ensure warranty coverage.
NOTES 30.
NOTES 31.
NOTES 32.
Safety Instructions & Operator's Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 17 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings.
An important point after buying a device Snapper RP2167517BVE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper RP2167517BVE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper RP2167517BVE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper RP2167517BVE you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper RP2167517BVE will certainly help you make a decision on the purchase.
If you already are a holder of Snapper RP2167517BVE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper RP2167517BVE.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper RP2167517BVE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper RP2167517BVE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
