Instruction/ maintenance manual of the product P216019KWV Snapper
Go to page of 32
Safety Instructions & Operator's Manual for 21" STEEL DECK WALK MOWERS SERIES 19 MODELS 2167519B P2167519B P217019BV P217019BVE P216019KWV MODEL NUMBER EXPLANATION SELF-PROPELLED CUTTING.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons.
IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE (Continued From Previous Page) 3. DO NOT remove fuel cap or add fuel with the engine running. Allow the engine to cool before refueling.
IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE AND STORAGE (Continued From Previous Page) 9. Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them. 10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 2 - 4 TABLE OF CONTENTS ...................................................................................................... 5 SECTION 1 - FAMILIARIZATION .
Section 1 - FAMILIARIZATION / ENGINE SPEED CONTROL ROPE / START HANDLE WHEEL DRIVE CONTROL GRASS BAG REAR HEIGHT ADJUSTMENT LATCH BLADE CONTROL / GRASS BAG ADAPTER GROUND SPEED CONTROL FUEL FILL FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened.
Section 2 -OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2.3 2.2.1. ENGINE & BLADE (Kawasaki Engine) 1. Make sure fuel valve on engine is open. See Figure 2.5. STOPPING Stop forward motion of mower by releasing the wheel drive control. Stop engine and blade by releasing the blade control.
Section 2 -OPERATING INSTRUCTIONS 2. Set all wheels at the same cutting height. The highest cutting position is Notch 7. The lowest cutting position is Notch 1. See Figures 2.8 & 2.9. STEP la (Kawasaki only): Attach Bag Adapter Standoff between rope guide pulley assembly and engine recoil.
Section 2 -OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 2 -OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 3- MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.
Section 3- MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS 4.5. BATTERY SERVICE 4.5.1. NEW BATTERY PREPARATION 1. Remove battery from carton. 2. Place battery in a well ventilated area on a level non-concrete surface. 3. Remove battery cell caps. Fill cells as required with electrolyte (supplied with battery) to proper level.
PROBLEM Engine Will Not Start Using Recoil Starter Engine Stalls or Stops After Running Engine Loses Power Excessive Vibration Mower Will Not Move Loss Of Traction (Self-Propelled Models) Cutting Grass Improperly Poor Grass Discharge Oil Leaking TROUBLESHOOTING PROBABLE CAUSE 1• Fuel tank empty• 2• Engine needs choking or priming.
SERVICE SCHEDULE ITEM Engine Oil SERVICE PERFORMED REF. Check Oil Level Page 7 EACH 5 25 USE HRS HRS X 5O HRS 100 HRS Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre-Cleaner Clean .
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of cha.
PRIMARY MAINTENANCE III illustration of engine & how Q It: can protect" v Snapper uses the best avail- ab!e engines and components in their products In; order to care Is easentfai In prolonging engine life.
PRIMARY MAINTENANCE men_ the air available to your S_ppar engine Is" heavily eatura_ wl_ air- quickly mln an engine, manufactumre equip their engines with extremely _clent air cleanere to As the .
PRIMARY MAINTENANCE Generelly_ wash foam-type filters in a dlshwashlng detergent and water solution. Rinse and wring dry, then saturate with oil and squeeze out excess, Failure to re-off this type fitter will ruin the Clean paper elements by tapping lightly.
PRIMARY MAINTENANCE On 4_yle engines with an otl level plug, don't be fooled into thinking the engine has sufficient lubricating oll if you can see "some" brought up to the point top of the fill hole. On 2-cycle englnee, lubrication must be provided by an exact mixture of gasoline and 2-cycte air--led engine oiL A 2.
SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper purchase) Model Number Serial Number Date of Purchase Retailer Retailer's Phone Number It is very important that you register your purchase with Snapper to ensure warranty coverage.
NOTES 30.
NOTES 31.
Safety Instructions & Operator's Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 19 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings.
An important point after buying a device Snapper P216019KWV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper P216019KWV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper P216019KWV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper P216019KWV you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper P216019KWV will certainly help you make a decision on the purchase.
If you already are a holder of Snapper P216019KWV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper P216019KWV.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper P216019KWV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper P216019KWV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
