Instruction/ maintenance manual of the product NZM25523KWV Snapper
Go to page of 14
Safety Instructions & Operator's Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 3 MODELS NZM19483KWV NZM21523KWV NZM25523KWV NZM25613KWV NZM27 613KH MODEL NUMBER EXPLANATION INI ; MODEL DESIGNATION .
Section 2 - SAFETY MESSAGES AND SYMBOLS I DANGER ! ROTATING PARTS I KEEP AWAY FROM MOVING PARTS I MOTION CONTROL LEVER OPERATION I I PARKING BRAKE LEVER OPERATION I I WEAR HEARING PROTECTION I f TO AVOID INJU RY OR DEATH PARA EVITAR LESIONES O LA MUERTE - Read Operator's Manual Do not operate unless you am e fully tRained.
Section 2 - SAFETY MESSAGES AND SYMBOLS PULL SWITCH "UP" TO ENGAGE BLADES PUSH SWITCH "DOWN" TO HOUR METER DISENGAGE BLADES OFF/STOP FAST RUN KEYSWITCH START I CONTROL PANEL IDENTI.
Section 2 - SAFETY MESSAGES AND SYMBOLS I ROLL BARPROTECTIVESTRUCTUREDECALS I I CAUTION! SPRING LOADED MECHANISM I.
Section 3 - OPERATING INSTRUCTIONS 3.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.
Section 3 - OPERATING INSTRUCTIONS 3,4,2, STOPPING MACHINE 1, Return motion controt lever to the neutral position & the neutral lock position. IMPORTANT: Operator must use hand assistance to bring both motion control levers to the neutral position & the neutral lock position.
Section 4 - MAINTENANCE WARN IN G Allow engine to cool for at least ten minutes before performing service or maintenance. DO NOT smoke near fuel components when performing service or maintenance. DO NOT perform service and maintenance near an open flame.
Section 5 - ADJUSTMENTS & REPAIR Ik DANGER Exercise EXTREME CAUTION when making this I adjustment, due to close proximity of moving parts. I 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement and stopping of the machine.
Section 5 - ADJUSTMENTS & REPAIR 5.1 NEUTRAL POSITION ADJUSTMENTS 5.2 (Continued From Previous Page) 12, With motion control levers remaining in the neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of rod.
Section 5 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remove spark plug wires and secure away from spark plugs. Engine and components are HOT.
Section 5 - ADJUSTMENTS & REPAIR 5.6 TRACKING ADJUSTMENT If the machine does not track straight when the Motion Control Levers are in the maximum forward speed position, perform the following adjustment. Rear tire pressure must be set to 12 PSi before making this adjustment.
Section 5 - ADJUSTMENTS & REPAIR 5.11 MOWER SPINDLES (Field Serviceable Spindles) BEARING REPLACEMENT In the event that a spindle bearing requires replacement, the SNAPPER Field Serviceable Spindles have been designed so that no special tools or presses are required.
Section 5 - ADJUSTMENTS & REPAIR 5.12 HYDRAULIC SYSTEM, PURGING After replacing or repairing hydraulic system components, one or both of the wheel drives may not pull properly.
Safety Instructions & Operator's Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 3 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings.
An important point after buying a device Snapper NZM25523KWV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper NZM25523KWV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper NZM25523KWV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper NZM25523KWV you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper NZM25523KWV will certainly help you make a decision on the purchase.
If you already are a holder of Snapper NZM25523KWV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper NZM25523KWV.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper NZM25523KWV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper NZM25523KWV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
