Instruction/ maintenance manual of the product MCRP215014KWV Snapper
Go to page of 29
Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK MOWERS “M ” M ODEL SERIES 14 MODELS PUSH M ODELS PROPELLE D M ODELS MR215014B MCRS215014KWV MRP216014B MRP216014T MCRP215014.
2 IMPORTA NT SA FETY INSTRUCTIONS WARNING: This powerf ul cuttin g machine is capable of amp utating hand s and feet and can t hrow ob jects that can cause in jury and damage! Failure to comply wi th the follo wing SAFETY inst ructions coul d result in serious injury or death to the ope rator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS OPERA TION 1. DO NOT put hands or feet near or under rotating parts. Keep clear of discharg e area while engin e is running. 2. STOP engine w hen crossing g ravel drives, w alks, or roads, and unde r any conditions where thrown objects might be a haza rd.
4 TA BLE OF CONTENTS IMPORTA NT SAFETY INSTRUCTIONS ............................................. 2 & 3 TA BLE OF CO NTENTS ............................................................................ 4 SECTION 1 - FA MILIAR IZA TION .............
5 Section 1 - FA MILIA RIZA TION FIGURE 1.1 1.1 INTRODUCT ION This manual has been prepar ed for the operators of the SNAPPER W ALK BEHIND MOW ERS. Its purpose, aside from recom mending oper ating and routine servic e requirements , is to promote safety through the use of accepted operating practices .
6 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-STA RT CHECK LIST Make the following c hecks and per form the service required bef ore each start-up. 2.1.1. Check guards, deflectors, gr ass bag, adapter and covers to mak e sure all are in plac e and securely tightened.
7 Section 2 - OPERA TING INSTRUCTIONS 2.2 STA RTING & OPERA TION 2.2.2. ENGINE & BL AD E (Choke M odels)(Commercial Only) 1. Move chok e/engine speed control to the “C hok e ” position. See Figure 2.4. NOTE: Stop the engine (and blade) by releasing the blade control.
8 Section 2 - OPERA TING INSTRUCTIONS WA RNING Before attempting any adjustments to the cutting height, STOP the engine, remove the spar k plug wire from the spark plug and secure wire away from plug. DO NO T make any adjustments w ith engine or blade running.
9 Section 3 - MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the m ower, use genuine SNAPPER replacem ent parts only. Contact a local SNAPPER dealer for parts and service assistanc e. For the cor rect part or inform ation for a particular mower, always mention m odel and serial num ber.
10 Section 3 - MA INTENA NCE 3.2.2. CHECK GREASE LEVEL IN T RA NSMISSIO N NOTE: Do not spill gr eas e or oil on sur f ac e of drive disc. See Figure 3.3. 3. Reinstall trans mission plug. 4. Thereaf ter, check grease level af ter each 25 hours of operation.
11 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attemp ting any adjustments o r repairs, STOP the en gine, remov e the spark plug w ire from the spark plug an d secure wire aw ay from plug. W ear heavy leather gloves when handling or working around cutting blades.
12 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attemp ting any adjustments o r repairs, STOP the en gine, remov e the spark plug w ire from the spark plug an d secure wire aw ay from plug. 4. Sharpen blade on a grinding wheel at an angle of 22 to 28 degrees.
13 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attemp ting any adjustments o r repairs, STOP the en gine, remov e the spark plug w ire from the spark plug an d secure wire aw ay from plug. 4.3 DRIVEN DISC SER VICE If the mower does not propel itself properly , refer to Figure 4.
14 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attemp ting any adjustments or repairs, STOP the engin e, remove the spark plu g wire from the spark plug an d secure wire aw ay from plug. 4.3.3. DRIVEN DISC ADJUSTM ENT (Continued From Previous P age) 2.
15 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attemp ting any adjustments or repairs, STOP the engin e, remove the spark plu g wire from the spark plug an d secure wire aw ay from plug. 4.3.4. Replacing Rubber Driven Disc Ring (Commercial Model) 2.
16 Section 4 - A DJUSTMENTS & REPA IR 4.3.6. Rep lacing Bearing In Driven Disc A ssembly (Commercial Models) If the driven dis c bearing fails , remove the dr iven disc assem bly and replace bearing as follows: 1. Using a sm all flat blade screwdriver, f ree the clip from the transf er rod.
17 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attemp ting any adjustments o r repairs, STOP the en gine, remov e the spark plug w ire from the spark plug an d secure wire aw ay from plug. 4.3.8. Replacement Of Bearing On Pu lley End Of Hex Shaft To replac e the bearing on the pulley end of the hex shaft, pr oceed as follows: 1.
18 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before at tempting any adjustments or repairs, ST OP the engin e, remove the spark plu g wire from the spark plu g and secure wire aw ay from plug. Wea r heavy lea ther gloves when handling or working around cutting blades.
19 Section 4 - A DJUSTMENTS & REPA IR WA RNING Before attemp ting any adjustments o r repairs, STOP the en gine, remov e the spark plug w ire from the spark plug an d secure wire aw ay from plug. Wea r heavy lea ther gloves when handling or working around cutting blades.
20 TROUBLESHOOTING PROBL EM PROBA BLE CA USE CORRECTIVE A CT ION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel. Using Recoil Starter 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine M anual for Instructions.
21 SERVICE SCHEDULE ITEM SERVICE PERFO RMED REF. EA CH USE 5 HRS 25 HRS 50 HRS 100 HRS EA CH SEA SON Engine Oil Check Oil Level Page 11 X Initial Oil Change Page 14 X Periodic Oil Change Page 15 X* A i r Pre-Cleaner Clean Sponge Element Engine Manual & Page 15.
22 3 YEA R LIMITED WA RRA NTY For thr ee ( 3) years from purc hase date f or the original purc haser's residential, non- com m erc ial use, SNAPPER , through any authorized SNA PPER dealer will r.
23 PRIMA RY MA INTENA NCE.
24 PRIMA RY MA INTENA NCE.
25 PRIMA RY MA INTENA NCE.
26 PRIMA RY MA INTENA NCE.
27 NOTES.
28 NOTES.
29 Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK BEHIND MOWERS “M ” M ODEL SERIES 14 WARNING: The engine exhaust from this product contains chemicals know n to the St ate of Californi a to cause cancer, birth defects or ot her reproductive harm.
An important point after buying a device Snapper MCRP215014KWV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper MCRP215014KWV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper MCRP215014KWV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper MCRP215014KWV you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper MCRP215014KWV will certainly help you make a decision on the purchase.
If you already are a holder of Snapper MCRP215014KWV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper MCRP215014KWV.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper MCRP215014KWV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper MCRP215014KWV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
