Instruction/ maintenance manual of the product ELT145H33GBV Snapper
Go to page of 41
Safety Instructions & Operator’s Manual for EUROPEAN LAWN TRACTOR HYDROSTATIC DRIVE SERIES G MODELS HYDROSTATIC DRIVE ELT145H33GBV MODEL NUM BER EXPLA NA T ION E LT 145 H 33 G B V EUROPEA N MO D.
2 IMPORTA NT SA FETY INSTRUCTIONS WARNING: This pow erful cuttin g machine is capable of amp utating hand s and feet and can t hrow ob jects that can cause injury and damag e! Failure to comply with the following SAFETY in stru ctions could resu lt in serious injury or death to the ope rator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS PREPA RATION (Continued From Pre vious Page) 7. Keep people and pe ts out of mowing area. Immediately STOP blades, STOP engine, and STOP mach ine if anyone enters the area. 8. Check shields, d eflectors, switch es, blade controls an d other safety dev ices frequently for proper oper ation and location.
4 TABLE OF CONTENTS IMPORTA NT SA FETY INSTRUCT ION S ............ 2-3 TA BLE OF CONTE NT S ........................................ 4 SEC TION 1 - FA MILIA RIZA TION ...................... 5-7 Compone nts .............................................
5 Section 1 - FA MILIA RIZA TION COMPONENTS The nom enclature drawings above, illus trate the essential com ponents of the SNAPPER Lawn Trac tor. It is recom m ended that all operators of this equipm ent becom e thoroughly fam iliar with the com ponents and their operation BEFO RE OPERATING.
6 Section 1 - FA MILIA RIZA TION – DECA LS / SYMBOLS A ll operators should locate, read and understand all decals on the Series G Law n T ractor before attempting any operation of the tractor.
7 Section 1 - FA MILIA RIZA TION – DECA LS / SYMBOLS FRA ME I NSTRUCTIONS DECAL B71.1-1998 CERTIFI CATION DECA L 7-2920 CONSOLE DE CAL 2-8561 RA BBI T ”FA ST” TURTLE “SLOW” CHOKE ENGINE “O.
8 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-ST A RT CHECKLIST Make the following c hecks and per form service as required bef ore each start-up. 2.1.1. Check tires and add air as needed to bring pressur e to 12 P.S.I. in front tires and 12 P.S.I. in rear tires .
9 Section 2 - OPERA TING INSTRUCTIONS 2.3 STA RTING & OPERA TION 2.3.1. STARTING ENGINE 1. T ake a com fortable position in seat of m achine, look ar ound to mak e sure that the area y ou are going to mow is c lear of people, childr en and pets.
10 Section 2 - OPERA TING INSTRUCTIONS 2.3 STA RT ING & OPE RA T ION (continued) 2.3.2. STARTING WHEEL DRIVE 1. Shift s peed control lever to neutral. 2. Start engine. Ref er to Section “START ING ENGINE” . 3. Release clutc h/brake pedal. 4. Slowly shift s peed control lever f orward for forward m otion or to the rear f or reverse m otion.
11 Section 2 - OPERA TING INSTRUCTIONS 2.4 STO PPING 2.4.3. STOPPIN G MO WER BLADE 1. Stop mower blade by moving blade engagem ent lever to the "OFF " position. See Figure 2.11. FIGURE 2.11 WA RNING Once blade is disengaged, it s hould come to a complete stop in 5 seconds or less.
12 Section 2 - OPERA TING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF Rolling Hydro Models 1. W ith engine "O FF", move to r ear of tractor . 2. Pull the roll releas e control all the way out to disengage the hydro transmis sion. See Figure 2.
13 Section 2 - OPERA TING INSTRUCTIONS 2.7. RE VERSE LOCKOUT MECHANIS M Data indicates that tragic back-over accidents occ ur each year. Thes e accidents us ually involve unsupervised children.
14 Section 3 - MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the Tr actor, use genuine SNAPPER replacem ent parts only. Contact a local SNAPPER dealer f or parts and servic e assistance. For the correc t part or inform ation for a particular Trac tor, alwa ys m e ntio n the model and ser ial number.
15 Section 3 - MA INTENA NCE 3.2.4. CHECK 33" DECK DRIVE BELT 1. W ith engine "OFF", m ove blade engagement lever to "ON". 2. Measure blade c able extension spring. Spring should extend 1" +/-1/8" f or proper belt tens ion.
16 Section 3 - MA INTENA NCE 3.3.4. TRACTOR LUBRICA T ION 1. Front W heel Bearings Lubricate each f ront wheel bearing through the grease f itting on w heel hub. Using general purpose grease in a greas e gun, add grease until grease purges f rom bearing.
17 Section 3 - MA INTENA NCE 3.3.4. TRACTOR LUBRICA T ION (Continued From Pre vious Page) 7. Steering T ie Rod Lubricate both ends of steering tie rod with a sm all amount of 30 wt. m otor oil fr om an oil can. See Figure 3.9. FIGURE 3.9 8. Blade Engagemen t Mechanism Using 30 wt.
18 Section 3 - MA INTENA NCE 3.4 A NNUALLY (END OF EA CH SEA SON) 3.4.2. FUEL FILT ER (Continued From Pre vious Page) 3. Install new fuel filter part num ber 1-4359. See Figure 3.13. FIGURE 3.13 4. Fill f uel tank with fresh gasoline. Ref er to engine owner's m anual for fuel s pecifications .
19 Section 4 - A DJUSTMENT & REPA IR WA RNING DO NOT attempt any adjustment s, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remov e key. Remove spark plug w ire from spark plug and secure wire aw ay from spark plug.
20 Section 4 - A DJUSTMENT & REPA IR 4.2.2. BLA DE BELT A DJUSTM ENT – 33” Deck (Continued from previous page ) IMPO RTA NT: If dec k front to rear level is not co rr ec t, this could cause blade belt pr oblems. 6. Move blade engagement lever to "ON".
21 Section 4 - A DJUSTMENT & REPA IR WA RNING DO NOT attempt any adjustment s, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remov e key. Remove spark plug w ire from spark plug and secure wire aw ay from spark plug.
22 Section 4 - A DJUSTMENT & REPA IR WA RNING DO NOT attempt any adjustment s, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remov e key. Remove spark plug w ire from spark plug and secure wire aw ay from spark plug.
23 Section 4 - A DJUSTMENT & REPA IR 4.3 TRACTOR DRIVE COMPONENTS 4.3.1. BRA KE ADJUSTMENT 1. To be properly adjusted, the brak e should stop the trac tor in approx imately 6 feet from top speed when the clutch/brak e pedal is fully depressed. 2. Adjust br ake when necess ary as follows: 3.
24 Section 4 - A DJUSTMENT & REPA IR WA RNING DO NOT attempt any adjustments, maint enance or service with the engine or blade running. STOP blade. ST OP engine. Set brake. Remove key. Remov e spark plug w ire from sp ark plug and secure wire away from spa rk plug.
25 Section 4 - A DJUSTMENT & REPA IR 4.4.2. (NINJA ) BLA DE WEA R LIM ITS The ninj a recycling blade requires m ore fr equent service intervals than s tandard blades. Check for exc essive wear and damage bef ore each use. See Figur e 4.18. FIGURE 4.
26 Section 4 - A DJUSTMENT & REPA IR 4.4.5. 33" M OWER BLADE REPLA CEM ENT (Continued) 6. Ins tall new blade, part number 3-4168, onto blade mounting bar . 7. T orque 30 to 40 ft lbs . 4.4.6. TRACTION DRIVE BELT REPLA CEM ENT It is necess ary to remove deck in order to replace belts.
27 Section 4 - A DJUSTMENT & REPA IR Traction driv e belt removal (Continued from previous page ) 2. Slide belt guide assem bly to the rear and rem ove. 3. Disconnec t traction belt idler pulley spring from tractor f rame. See F igure 4.26. FIGURE 4.
28 Section 4 - A DJUSTMENT & REPA IR Tractio n drive belt replacemen t (Continued from previous page ) NOTE: W hen ins talling a new belt, mak e certain the stationary idler is m ounted in the hole closest to the L.H. side of the trac tor. See Figure 4.
29 Section 4 - A DJUSTMENT & REPA IR 4.5 BA T TERY 4.5.1. BA T TERY REM OVA L 1. Raise operator 's seat. 2. Rem ove the two adjusting knobs. 3. Rem ove seat assem bly and move forward. Use care not to disc onnect wires from seat switch. See Figure 4.
30 Section 4 - A DJUSTMENT & REPA IR WA RNING DO NOT OVERFILL! DO NO T attempt to service or charge the b att ery wh ile it is installed on the machine. DO NOT use “BOOST ” chargers on th e battery. 4.5.5. BA T TERY T ESTING There are two types of battery tests: Unloaded and Loaded.
31 Section 4 - A DJUSTMENT & REPA IR A VA ILA BLE A CCESSORIES The SNAPPER Series F LAW N TR ACTO R can be equipped with a variety of accessor ies that incr ease its ver satility. The acces sories available for each model ar e listed in the c hart below.
32 SECTION 5 - ELECTRICA L SYSTEM Figure 5.1 illustr ates ty pic al harness routing on s ome Snapper Lawn T ractors. Us e this when locating various electric al com ponents.
33 SECTION 5 - ELECTRICA L SYSTEM SCHEMATICS BRIGGS & STRA T TON WIT HOUT LIGHTS FIGURE 5.2 BRIGGS & STRA T TON WIT H LIGHTS FIGURE 5.3.
34 TROUBLESHOOTING GUIDE PROBLEM PROBA BLE CAUSE CORRECTIVE A CTION Starter Will Not Crank Engine 1. Battery dead. 1. Service battery. 2. Blown fuse. 2. Replace fus e. 3. Electrical c onnections loose or c orroded. 3. Clean and check connections f or good contact.
35 TROUBLESHOOTING GUIDE PROBLEM PROBA BLE CAUSE CORRECTIVE A CTION Tractor Will Not Move Or L oss Of Traction 1. Speed control handle in the neutral “ N” position. 1. Place speed contr ol in desired speed. 2. Roll release contr ol in “ROLL” position.
36 MA INTENA NCE SCHEDULE SUBJECT SERVICE TO BE PERFORM ED REFERENCE PAGES EACH USE 5 HOURS 25 HOURS 50 HOURS 100 HOURS EACH SEASON Engine Check Oil Lev el Page 8 X Engine Initial Oil Change Page 14 X.
37 3 YEA R LIMIT ED WA RRANTY For three (3) y ear s from purchase date f or the original purchas er's residential, non-c omm ercial use, SN A PPER , through any authorized SNA PPER dealer will re.
38 SERVICE NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________.
39 SERVICE NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________.
40 SERVICE NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________.
41 Safety Instructions & Operator’s Manual for EUROPEAN LAWN TRACTOR HYDROSTATIC DRIVE SERIES G IMPORTANT Snapper products are built us ing engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines conta in very impor tant emissions infor mation and critical safety warnings.
An important point after buying a device Snapper ELT145H33GBV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper ELT145H33GBV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper ELT145H33GBV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper ELT145H33GBV you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper ELT145H33GBV will certainly help you make a decision on the purchase.
If you already are a holder of Snapper ELT145H33GBV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper ELT145H33GBV.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper ELT145H33GBV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper ELT145H33GBV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
