Instruction/ maintenance manual of the product 555 Snapper
Go to page of 32
OPERA T OR’S MANU AL Intermediate Sno wthr o wer Models 555 Models Mfg. No. Description 1694587 555M, 5HP Snowthrower, Manual Start 1694595 555M, 5HP Snowthrower, Manual Start (Export) 85665 I5225, 5HP Snowthrower, Manual Start 80494 EI5225, 5HP Snowthrower, Manual Start (Export) 860 Models Mfg.
1 T able of Contents Safety Rules & Inf ormation Training ...................................................................2 Preparation .............................................................2 Operation ...................................
2 This machine is capable of amputating hands and feet. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
3 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
4.
5 Identification Numbers When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access.
6 Safety Decals T raction Disengage T raction Engage Free Hand Unlocked Free Hand Locked AVOID SERIOUS INJUR Y OR DEATH • Read the operator's manual for operating and safety instructions. • Do not defeat the safety features of control. They are for your protection.
Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. 7 CE Safety Icons & Compliance Specs Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing.
8 Features, Controls, & Operation TECUMSEH MODELS BRIGGS & STRA TT ON MODELS Please take a moment and familiarize yourself with the name, location, and function of these controls so that you will better understand the safety and operating instructions provided in this manual.
9 Features & Controls Fuel Fuel tank filler cap (see illustration). Note: The fuel shut off valve is located under the fuel tank. Close the valve when the snowthrower is not in use. Open the valve before starting. Starter Handle Used to pull-start the engine.
10 Engine Controls ST AR TING CONTROLS See Figures 1 & 2 for the following instructions. Units with Optional Electric Start A. Electric Start Button - The electric start button (A) activates an electric starter mounted to the engine, eliminating the need to pull the starter han- dle.
11 Controls Figure 3. Operator's Control Position A. Speed Selector C. Auger Control B. Drive Control D. Chute Direction Control Figure 4. Snowthrower Controls A. Speed Selector E. Chute Deflector B. Drive Control F. Chute Deflector Knob C. Auger Control G.
12 Operation GENERAL OPERA TION CHECKS BEFORE EA CH ST ART -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out tool is attached to the handle on the machine. Do not oper- ate the machine without the clean-out tool properly stored on the handle.
13 Operation ST AR TING THE ENGINE 1. Turn the fuel valve (B, Figure 5 & 6) to the ON posi- tion. 2. Insert the engine key (F) into the engine key slot and push fully in to the RUN position. 3. Move the throttle lever (E) fully up to the FAST posi- tion.
14 Operation OPERA TING THE SNO WTHRO WER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger control (C, Figure 7) on the right-hand grip to begin auger rotation.
15 Operation DEFLECT OR The distance of the discharged snow is mainly controlled by the position of the deflector (Figure 9). (Engine speed also affects distance of discharge. Always operate at FULL throttle.) The more the deflector is tilted UP, the farther snow will be thrown.
16 Operation Figure 11. Traction Drive Lock - Disengaged FREE-WHEELING AND TRA CTION DRIVE LOCK For easy turning when pushing the snowthrower, you can disengage the traction drive at one or both wheels by using the traction lock pins (See Figures 11 & 12).
17 Regular Maintenance CHECK A UGER GEAR CASE LUBRICA TION 1. Place the snowthrower on a level surface. 2. Remove the pipe plug (Figure 14). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add The Dealer Line Winter Weight Worm Gear Oil (available from your dealer).
18 Maintenance Figure 15. Drive Area Lubrication Points (Bottom Cover Removed) A. Drive Disc C. Hex Shaft B. Friction Disc Figure 16. Snowthrower General Lubrication Points A B C Remove wheels and grease axles once each year. There are two grease fittings on the auger shaft.
19 Storage LUBRICA TION CHECK / LUBRICA TE FREE-HAND LINKA GE Check the function of the Free-Hand controls: the con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released.
T roubleshooting, Adjustment, & Service 20 PROBLEM POSSIBLE CA USE REMED Y Engine fails to start. 1. Key is OFF. 2. Failure to prime cold engine 3. Fuel valve is in CLOSED position. 4. Out of fuel. 5. Choke OFF - cold engine. 6. Engine flooded. 7.
21 T roubleshooting PROBLEM POSSIBLE CA USE REMED Y Auger rotates, but snow is not thrown far enough 1. Chute deflector too low. 2. Engine speed too slow. 3. Ground speed too fast. 4. Snowthrower discharge chute clogged. 5. Auger belt loose or worn. 1.
22 Adjustments SPEED SELECT OR PIV O T ADJUSTMENT The speed selector is factory set for optimal performance at each forward and reverse speed setting. However, if drive system components have been replaced, adjust- ment may be necessary. Adjust as follows: 1.
23 Adjustments MANU AL DISCHARGE CHUTE CONTR OL LINKA GE ADJUSTMENT Pinion Gear Adjustment If the discharge chute is difficult to operate, first lubricate the pinion gear (A, Figure 21) and ring gear (F).
24 Adjustments Figure 23. Auger Drive Clutch Cable Adjustment Auger Drive Clutch Cable Auger Drive Clutch Cable Spring Adjustment Hex Nut A UGER DRIVE CLUTCH CABLE ADJUSTMENT The auger drive clutch cable should be adjusted so that there is no slack in the cable when moved slightly from side to side.
25 Adjustments DRIVE BEL T ADJUSTMENT (Continued) If the auger drive slips (auger slows or doesn't rotate nor- mally while blowing snow), or stays engaged when the control is disengaged — and the auger clutch cable has been properly adjusted — the auger drive belt may be out of adjustment.
26 Adjustments & Service DRIVE BEL T ADJUSTMENT (Continued) Adjusting A uger Belt Guide 1. With the auger control still fully depressed, adjust the auger belt guide so that there is a 1/64” gap (1/32” Maximum) between the end of the guide and the belt (Figure 28), making certain the guide is NOT putting pressure on the belt.
27 Service DRIVE BEL T REPLA CEMENT (Cont.) A uger Drive Belt Replacement 1. Remove gas from fuel tank and run engine until it stops running from lack of fuel. 2. Disconnect spark plug wire and fasten it away from the spark plug. 3. Remove belt cover (See Figure 25).
28 Service SHEAR PIN REPLA CEMENT Under most circumstances, if the auger strikes an object which could cause damage to the unit, the shear pin will break. (This protects the gear box and other parts from damage.) The shear pins are located on the auger shaft as shown in Figure 32.
29 Specifications ENGINE: 5 HP* T ecumseh Make Tecumseh Model Snow King Horsepower 5 HP @ 3600 rpm Displacement 11.88 Cu. in (195 cc) Oil Capacity See Engine Owner’s Manual 8 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Snow Horsepower 8 HP @ 3600 rpm Displacement 18.
30 Replacement Parts & Accessories REPLA CEMENT P ARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. TECHNICAL MANU ALS Additional copies of this manual are available, as well as fully illustrated parts lists.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004, Simplicity Manufacturing, Inc.
An important point after buying a device Snapper 555 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper 555 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper 555 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper 555 you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper 555 will certainly help you make a decision on the purchase.
If you already are a holder of Snapper 555, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper 555.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper 555. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper 555 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
