Instruction/ maintenance manual of the product 5201E Snapper
Go to page of 12
5/2005 1 Manual No. 7100193 I.R. 6/10/2005 TP 300-5071-IR-SX-N Dealer Setup & Adjustment Instructions 520 Series Single Stage Snowthrower T ABLE OF CONTENTS: SAFETY RULES ........................................................2 SETUP PROCEDURES Quick Setup List .
520 Single Stage Snowthr ower 5/2005 2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of equipment, severe personal injury or death to you, yourself or bystanders, or damage to property or equipment.
Quick Setup List - 520 Single Stage Snowthr ower 5/2005 3 P age Setup Procedure Steps to P erform 4 Unbo x & Assemble ❏ Remov e Unit F rom Bo x. ❏ Install Discharge Chute ❏ Assemble Handle B.
520 Single Stage Snowthr ower 5/2005 4 Unbo xing & Assembl y 1. Using a utility knife, open the box and remove the snowthrower. 2. Install the discharge chute on to the rotating ring located on the auger housing.
FUEL TO OIL MIXTURE CHART (50:1) U.S. Imperial Metric Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil Gallons Ounces Gallons Ounces Liters Milliliters 1 2.
520 Single Stage Snowthr ower 5/2005 6 Figure 8. Grease the Discharge Chute Ring Lubricate Flange Removing Belt Co ver In order to perform proper lubrication, it is necessary to remove the Belt cover from the lower left of the snowthrower. 1. Remove the Engine Key from the switch.
520 Single Stage Snowthr ower 5/2005 7 T est Run Test run the unit for several minutes. Check that the following work properly: • Primer • Choke • Recoil Starter • Electric Starter (Where Appl.
520 Single Stage Snowthr ower 5/2005 8 Figure 10. Cover Removal & Installation Insert front tabs first when reinstalling cover. Align rear tabs & side of cover when reinstalling.
520 Single Stage Snowthr ower 5/2005 9 A uger Control Cab le Adjustment The length of the auger control cable is adjustable. However, it will seldom be necessary to change the cable length since the operating tension on the drive belt is maintained by the spring on the end of the cable.
520 Single Stage Snowthr ower 5/2005 10 Service Notes.
520 Single Stage Snowthr ower 5/2005 11 Service Notes.
520 Single Stage Snowthr ower Manual No. 7100193 I.R. 6/10/2005 TP 300-5071-IR-SX-N 5/2005 12 Replacing the Drive Belt 1. Remove Engine Key from switch.
An important point after buying a device Snapper 5201E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper 5201E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper 5201E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper 5201E you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper 5201E will certainly help you make a decision on the purchase.
If you already are a holder of Snapper 5201E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper 5201E.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper 5201E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper 5201E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
