Instruction/ maintenance manual of the product 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3 Snapper
Go to page of 40
Safety Instructions & Operator’s Manual for REAR ENGINE RIDING MOWER SERIES 23 MODELS 281123BV 2811523BV 281223BVE 2812523BVE 2813523BVE 301123BV 3011523BV 301223BVE 3012523BVE 3013523BVE 331323.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 6. Check the area to be mow ed and remove all objects such as toys, w ire, rocks, limbs and other objects that could cause injury if thrown by blade or interfere w ith mow ing.
4 IMPORTANT SAFETY INSTRUCTIONS TOWING 1. Tow only with a machine that has a hitch designed for tow ing. DO NOT attach tow ed equipment except at the hitch point. 2. Follow the manufacturer’s recommendation for w eight limits for tow ed equipment and tow ing on slopes.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ..................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON .
6 Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER Rear Engine Rider. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices.
7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 12 PSI in front and 12 PSI in rear tires.
8 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to “START”, the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “OFF” position (See Figure 2.
9 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. ENGINE (ELECT RIC START) (Continued) 8. Should the battery be too weak to start the engine, refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines.
10 Section 2 - OPERATING INSTRUCTIONS WARNING Once blade is disengaged, it should come to a complete stop in 3 seconds or less. If the blade continues to rotate after 3 seconds, the blade brake must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment.
11 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT leave the machine w ith the engine running. STOP Blade. STOP engine. Shift to neutral and engage park brake. Remove key . 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.1. ENGINE 1. Stop engine by turning key to the “OFF” position.
12 Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.4. PARK BRAKE 1. Engage park brake by pushing clutch/brake pedal “DOWN” and moving the park brake latch to the “ENGAGED” position. While holding the park brake latch “ENGAGED”, release clutch/brake pedal to set park brake.
13 Section 2 - OPERATING INSTRUCTIONS 2.6 REVERSE LOCKOUT MECHANISM Data indicates that tragi c back-over accidents occur each year. These accidents usually involve unsupervised children.
14 Section 3 – MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
15 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
16 Section 3 – MAINTENANCE 3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.7. SAFETY INTERLOCK SYSTEM CHECKS Perform the following interlock sy stem checks periodically during the operat ing season. Contact your authorized Snapper dealer if you have questions.
17 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blades running. Stop blades. Stop engine. Engage parking brake. Remove key. Remove spark plug wires from spark plugs and (gas only) secure wires aw ay from spark plugs.
18 Section 3 – MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
19 Section 3 – MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
20 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
21 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
22 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
23 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
24 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
25 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
26 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
27 Section 4 - ADJUSTMENTS & REPAIR WARNING The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire aw ay from area when charging battery or when handling electrolyte or battery. Electroly te (acid) is a highly corrosive liquid.
28 Section 4 - ADJUSTMENTS & REPAIR 4.6.6. BATTERY TESTING Batter y Condition Chart State of Charge Syringe Hy drometer Di gital Voltmeter Five Ball Hy drometer 100% Charged w/ Sulfate Stop 1. 280 12.80v Five Balls Floating 100% Charged 1.265 12.60v Four Balls Floating 75% Charged 1.
29 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not 1. F u el t a nk e m pt y. 1. Fill fuel tank with fresh fuel to proper level. Start Using 2. Engine needs choking. 2. Move choke control to “CHOKE” position. Recoil Starter 3.
30 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Rider Will Not Move 1. Drive disc worn or dama g ed. 1. Re p lace drive disc. Loss Of Traction 2. Rubber drive disc is not tracking properly on drive disc. 2. Adjust rubber drive disc. 3. Tapered axle bolt and nut missing.
31 MAINTENANCE SCHEDULE SUBJECT SERVICE TO BE PERFORMED REFERENCE PAGES EACH USE 5 HOURS 25 HOURS 50 HOURS 100 HOURS EACH SEA SON Engine Check Oil Level Page 7 X Engine Initial Oil Change Page 14 X En.
32 MAINTENANCE/REPLACEMENT PARTS MAINTENANCE PARTS Engine Speed Control (Briggs Engine) 7022751 Engine Speed Control (Kohler Engine) 7074320 Engine Speed Control (Honda Engine) 7075089 Clutch/Brake Ca.
33 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
34 PRIMARY MAINTENANCE.
35 PRIMARY MAINTENANCE.
36 PRIMARY MAINTENANCE.
37 PRIMARY MAINTENANCE.
38 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following information .
39 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
40 Safety Instructions & Operator’s Manual for REAR ENGINE RIDING MOWER SERIES 23 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
An important point after buying a device Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE will certainly help you make a decision on the purchase.
If you already are a holder of Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper 281123BV, 2811523BV, 281223BVE, 281523BVE, 2813523BVE, 301123BV, 3011523BV, 301223BVE, 3012523BVE, 3013523BVE, 331323HVE, 331523KVE, 331623BVE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
