Instruction/ maintenance manual of the product 1721303-01 Snapper
Go to page of 18
A TT A CHMENT OPERA T OR’S MANU AL Snow Plo w/Dozer Blade Mfg. No. Description 1693754 42” Remote Angling Snow Plow/Dozer Blade Hitch Mfg. No. Description 1693757 Hitch (for Sovereign / 900 / 2800.
1 T able of Contents Maintenance & Normal Care Schedule ..............6 Schedule f or Nor mal Care ...............................6 Lubricate the Dozer Blade ...............................6 Adjustments ............................................
OPERA TING SAFETY ● Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. ● Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads.
3 TRA CT OR CONTROLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and stop the unit.
4 Checks Bef ore Starting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity.
5 General Operating Instructions Daily Stora ge 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion.
6 Maintenance Schedule For Normal Care Care Required Schedule Clean debris from After each use. dozer blade. Lubricate dozer blade. Every 10 hours or at least once a year.
7 Adjustments Skid Shoe Adjustment Slotted holes are provided to permit adjustment of the shoe assemblies for raising and lowering the blade to various working heights (see Figure 3). When cleaning snow from gravel or earth drives or walks, the shoe assemblies should be lowered fully to prevent blade contact with gravel or ground.
8 Adjustments Figure 6. Adjusting Lift Rod A. Front Set Collar B. Rod Guide C. Spring D. Rear Set Collar E. Spring Clip Lift Rod Adjustment In the fully raised position the blade should be 6” off the ground. In the fully lowered position, the lift rod should slightly compress the spring creating downward pressure on the blade.
9 Initial Setup & Assembly Ref Qty Description 1 1 ROD, Control Handle, Upper 2 6 NUT, Hex, 5/16-18 3 2 LOCKWASHER, 5/16 4 4 WASHER, 5/16 5 2 CAPSCREW, 5/16-18 x 1-1/4 6 1 ROD, Control Handle, Low.
10 Initial Setup & Assembly 2 1 3 5 6 7 9 15 10 11 9 8 8 8 8 4 4 3 13 12 14 18 17 21 16 20 19 16 18 Ref Qty Description 1 2 STOP, Bar 2 2 SCREW, Taptite, 5/16-18 x 1 3 2 SETSCREWS, 5/16 x 1/2 4 2 SET COLLAR 5 1 ROD GUIDE ASSY.
11 Initial Setup & Assembly INITIAL SETUP & ASSEMBL Y NOTE: Some of the following setup procedures may already be completed. Assemble Blade 1. Place the blade on a flat surface. 2. Install the bar stops (A, Figure 9) using the two 5/16- 18 x 1 taptite screws (B).
12 Initial Setup & Assembly Install Blade 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake. 3. Raise rear of push bar so its arms fit between lugs of hitch (A, Figure 12) just behind front axle.
13 Initial Setup & Assembly Figure 13. Control Rod Support A. Angling Support D. 5/16 Flatwasher B. Eyebolt & Locknut E. Flange Locknuts C. 5/16-18 x 1-1/2 Capscrews Install Angling Control Ro.
14 Attaching & Removing REMO V AL & INST ALLA TION Removing & Attac hing Dozer Blade 1. Lower the blade. 2. Remove the hair pin clip and washer (D, Figure 15) securing the angling control rod to the clevis. Disconnect the angling control rod.
15 T orque Specification Chart FOR ST ANDARD MACHINE HARDW ARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
16 NO TES.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2000 Simplicity Manufacturing, Inc.
An important point after buying a device Snapper 1721303-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper 1721303-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper 1721303-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper 1721303-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper 1721303-01 will certainly help you make a decision on the purchase.
If you already are a holder of Snapper 1721303-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper 1721303-01.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper 1721303-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper 1721303-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
