Instruction/ maintenance manual of the product 04134XX0 Axor
Go to page of 16
Metris S 04135XX0 Metris S 04126XX0 T alis S 04136XX0 T alis S 04127XX0 Focus S 04137XX0 Focus S 04128XX0 Solaris E 04138XX0 Solaris E 04129XX0 Allegro E 04139XX0 Allegro E 04130XX0 Swing C 04143XX0 S.
2 T wo-hole thermostatic tub filler -- requires rough 04125181 04135XX0 04136XX0 04137XX0 04138XX0 04139XX0 04140XX0 04143XX0.
3 Three-hole thermostatic tub filler -- requires rough 04124181 04129XX0 04128XX0 04127XX0 04126XX0.
4 T echnical Information Recommended water pressure 45 - 72 psi Recommended hot water temp. 120 � - 140 � F* Max. hot water temp 165 � F* Max. flow rate 8 gpm Max. flow rate – handshower 2.5 gpm Safety stop 100° F *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater .
5 Install the valve trim Push the escutcheon over the valve. Install the handle. T ighten the screw with a 3 mm Allen wrench. The screw must engage the slot on the cartridge. Justify the handle. Set the high temperature limit stop. Push the spout sealing ring firmly into the spout adapter (1).
6 Install the handshower Pull the end of the handshower hose from the holder . Push the escutcheon over the end of the hose. Push the elbow firmly over one end of the handshower hose. T ighten the hose nut. Thread the hose down through the handshower holder escutcheon and handshower holder .
7 Set the high temperature limit stop T urn the water on to the tub spout or handshower . Use a 3 mm Allen wrench to loosen the handle screw . Remove the handle from the valve. Carefully remove the retainer clip and the limit stop ring. T urn the temperature control stem until the water is the desired high temperature, usually 110°F* .
8 Justify the handle T urn the water on to the tub spout or handshower . Place a thermometer in the water stream. T ur n the temperature control knob until the output wa- ter temperature is 100°F . T urn the water off. Install the stop ring so that it is against the stop -- you should not be able to turn the stem fur ther counter-clockwise.
9 Loosen the handle screw with a 3 mm Allen wrench. Remove the handle. Hold the handle lever in one hand. With the other hand, turn the temperature control knob until the 100° mark is next to the indexing mark on the handle. Install the handle on the valve.
10 User Instructions - ThermoBalance valve T urn the lever clockwise to send the water to one function, counter-clockwise to send the water to the second function. The center position is off. T urn the temperature control knob clockwise to make the water cooler .
11 Maintenance: Clean the filters T urn off the water at the main before opening the valve. Remove the handle and escutcheon. Rinse the handshower with clear water . Install the handshower . T urn on the water and flush the hand- shower for at least one minute.
12 Install the escutcheon. Justify the handle. Rinse the debris from the filters, using a soft toothbrush if necessar y . Do not at- tempt to remove the screens. Lubricate the o-rings with white plumbers grease. Hold the stop unit steady . Install the ther- mostatic cartridge.
13 Replacement parts 1 2 6 4 5 3 7 8 12 13 14 15 16 17 18 8 8 8 8 8 8 12 12 12 12 14 14 14 15 15 15 15 13 13 16.
14 1 Solaris E handle 88530XX0 2 T alis S handle 88549XX0 3 C handle 88610XX0 4 Metris S handle 88713XX0 5 Focus S handle 88714XX0 6 Allegro E handle 88719XX0 7 Metro E handle 88721XX0 8 handle escutc.
15 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
16 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No.
An important point after buying a device Axor 04134XX0 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Axor 04134XX0 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Axor 04134XX0 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Axor 04134XX0 you will learn all the available features of the product, as well as information on its operation. The information that you get Axor 04134XX0 will certainly help you make a decision on the purchase.
If you already are a holder of Axor 04134XX0, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Axor 04134XX0.
However, one of the most important roles played by the user manual is to help in solving problems with Axor 04134XX0. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Axor 04134XX0 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
