Instruction/ maintenance manual of the product 7307 Smarthome
Go to page of 15
T otal Protection Alarm System SMARTHOME™ #7307 PA T . D410633 Patents Pending SMARTHOME.COM™ 1-800-SMART-HOME 949-221-9200 http://www.smarthome.com Order #7307.
– 2 – Y our Guide to the T otal Protection Alarm System SMARTHOME™ #7307 – 3 – P ACKAGE CONTENTS........................................................................4 OVE R VIE W ...........................................................
P ACKAGE CONTENTS Everything required for installation is included with this package 1 Control Panel (SC-001) includes: 1 antenna (installed) 1 AC adapter 1 9 volt alkaline battery T wo sets of Door/W.
– 6 – PLANNING YOUR HOME SECURITY NEEDS Before you begin to install your security system, analyze the premises to determine your security needs. Consider those doors and windows which are more likely to be used as points of entry by an intruder , the ones that are poorly lit or the entrances that can not be seen from the street.
4. Attach the unit to the wall. If hanging the unit, insert two screws using the template provided. If screwing the back directly to the wall, take the back plate right off by prying apart one hinge. Use as much force as needed. The plastic hinge will not break.
– 10 – (Cont. : Installing the motion sensor (PS-433) Set the switch on the side t o "TEST" and allow 60 seconds for the unit to warm up. ( when using test mode, a signal will not be sent to the Control Panel ). Now walk in the area you want the motion sensor to detect movement in.
LIGHTS AND SOUNDS If you make a mistake while programming, the Control Panel emits three short beeps. That means the system has cleared and you must start the pro- gramming sequence from the beginning.
– 14 – ST ANDARD PROGRAMMING Option 2: Home Sequence - T o arm your system when someone remains in the premises. 1. Press the current MPIN [ 0 0 0 ].
– 16 – KEYCHAIN TRANSMITTER (4B-434) TO DISARM THE SYSTEM, OR DEACTIV A TE THE SIREN USING THE KEYCHAIN TRANSMITTER When the system is armed: Press button #3. The red light on the transmitter flashes and the Control Panel beeps twice. The system is now disarmed.
– 18 – SECONDAR Y PERSONAL IDENTIFICA TION NUMBER (SPIN) Y ou may want to give someone limited access to the system, (baby sitter , cleaner , repairman etc.). For this purpose the SC-100 provides you with the option of adding up to 3 separate SPIN.
– 20 – ADV ANCED PROGRAMMING T o program sensors to send their signals to a different zone, you must first clear them from communicating with their current zone. TO CLEAR A ZONE 1. Enter the current MPIN. 2. Press [ B ]. 3. Press the number key to identify current zone [ 1, 2, 3 or 4 ].
– 23 – ADV ANCED PROGRAMMING 1. Enter the current MPIN. 2. Press [ A ]. 3. Press [ A ]. Y ou will hear a long beep. The arm light, the red and green lights in zones 1 and the red lights in zones 3 and 4 go on. Zone 1 has the entry delay to allow someone to enter through the front door and deactivate the system before the siren sounds.
– 25 – Below is a table summarizing all the preprogrammed sequences. Sequence Zone 1 Zone 2 Zones 3 & 4 When sequence should be used FOR TESTIN G MPIN A # chime chime chime use for testing aft.
– 27 – BA TTER Y MAINTENANCE MOTION SENSOR BA TTER Y The Motion Sensor operates on a 9 volt alkaline battery accessible beneath a sliding panel on the botto m of the unit. All re mote sensors come with the battery already installed. Disarm the Control Panel before replacing all batteries.
KEYCHAIN TRANSMITTER BA TTER Y The Keychain Transmitter operates on a 12 volt alkaline battery which is installed at the factory . There are two screws on the back of the transmitter that holds the case together . T o replace the Keychain T ransmitter battery: 1.
An important point after buying a device Smarthome 7307 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smarthome 7307 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smarthome 7307 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smarthome 7307 you will learn all the available features of the product, as well as information on its operation. The information that you get Smarthome 7307 will certainly help you make a decision on the purchase.
If you already are a holder of Smarthome 7307, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smarthome 7307.
However, one of the most important roles played by the user manual is to help in solving problems with Smarthome 7307. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smarthome 7307 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
