Instruction/ maintenance manual of the product 91558-01A SkyLink
Go to page of 16
-J02028 REV . 2010-09-07 REMO TE CONTR OL GARA GE DOOR OPENER KITS GENERAL Kit Numbers 91558-01A (T ransmitter/Receiver Kit), 91561-01 (T ransmitter Kit), 91562-01 (Receiver Kit) Models F or model fitment inf ormation, see the P&A retail catalog or the P ar ts and Accessories section of www .
RECEIVER INST ALLA TION Kits 91558-01A and 91562-01 only 1. Unplug the power cord from the gar age door drive unit to pre vent door activ ation dur ing installation. 2. Select an unswitched 110V po wer outlet in the garage located either highest in the garage, closest to the front of the garage, or both.
For Dyna, Softail and Spor tster models: When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity . Gasoline is extremel y flammable and highly e xplosive , which could result in death or serious injury . (00330a) 3. The fuel tank must be remov ed or slightly raised to access wiring under neath.
2000 and Later Softails, Except Deuce (FXSTD) 1. Remov e the fuel tank mounting bolts. See the correct section (Carbureted or EFI Engine) of the service manual. 2. Remov e the rear splash guard (inner fender) per service manual instructions. 3. See Figure 4.
3 1 2 is06715 1. T ransmitter mounting location 2. Wires to headlamp 3. Ignition module Figure 7. T ransmitter Mounting and Wire Routing, (2003 or Earlier Sportster Models) 2004 and Later Sportster Models 1. Remov e the fuel tank. See the correct section (Carbureted or EFI Engine) of the ser vice manual.
1 5 6 2 3 4 is06718 1. Mount transmitter to fairing 2. Headlamp connector 3. Orange/white wire 4. Black wire 5. White wire 6. Y ello w wire Figure 10. Wires for T ransmitter Connections (FL TR) 2002-2003 V -Rod Models 1. See Figure 11. Remov e the screw (3) f astening the front left louvered co ver (1) to the motorcycle.
HARNESS CONNECTION General Splicing of wire leads is necessar y in the installation of the garage door opener to the v ehicle. Find the instructions f or a specific model in the sections that f ollow , and ref er to the ser- vice manual appendix f or proper wire splicing procedures.
1 2 3 is02055a 1. 1 into 1 splice 2. 2 into 1 splice 3. 3 into 1 splice Figure 15. Splice Configurations NO TE Electrical connectors are identified in the ser vice manual by the number and letter shown here within br ack ets.
1 1 is01103 1. Ground scre ws (blac k wire) Figure 16. Ground Connections (Sportster Models) 2002-2003 V -Rod Models 1. Cut the blac k transmitter ground wire to within easy reach of one of the ground scre ws located on the engine cam cov ers. Remove the g round screw .
5. Pull only the orange/white wire out of the longer piece of conduit on the garage door opener wire harness. Cut the e xcess length from the orange/white wire to within easy reach of the adapter wire. 6. See Figure 15, the 1 into 1 splice configuration.
NO TE On some Spor tster models the ignition module must be remov ed to access the orange/white wire in the main harness. 1. See Figure 20. Carefully slice open an area of the main harness wrap inside the electr ical side cov er or under the seat at an accessible point, and cut an or ange/white main harness power lead.
1 is06731 1. Headlamp connector [38] Figure 23. Wire Splice Locations (2005 and Later V -Rod) YELLO W AND WHITE LEAD CONNECTIONS T O HEADLAMP Dyna Models 1. See Figure 24. Use cable straps from the kit to f asten the remaining transmitter wires (y ellow and white) and conduit to the motorcycle wires leading to the headlamp .
2 1 is06727 1. White and yellow headlamp wires 2. Cut headlamp wire casing to access wires Figure 25. White and Y ellow Wire Optional External Splice Location (Sportster Models) 3. Cut the yello w and white wires in the headlamp housing se ver al inches from the headlamp connector .
RECEIVER AND TRANSMITTER PROGRAMMING After the receiver and tr ansmitter are installed, the receiv er must be progr ammed to receive the tr ansmitter frequency . This process ma y require two people, depending upon ho w far apar t the receiver and tr ansmitter are during the programming pro- cess.
SER VICE P ARTS 2b 2a 3 8 6 4 1 7 5 14 10 11 15 13 12 9 is06735 Figure 27. Ser vice P arts, Remote Contr ol Garage Door Opener Kits T able 1. Service Parts, Garage Door Opener Kit 91558-01A P art Numb.
SER VICE P ARTS T able 2. Service Parts, T ransmitter Kit 91561-01 P art Number Description (Quantity) Item Not sold separately T ransmitter assembly 1 91650-01 Hardware kit (includes items 3 through 9) 2b Not sold separately • F oam tape, doub le-sided, 1.
An important point after buying a device SkyLink 91558-01A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought SkyLink 91558-01A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data SkyLink 91558-01A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, SkyLink 91558-01A you will learn all the available features of the product, as well as information on its operation. The information that you get SkyLink 91558-01A will certainly help you make a decision on the purchase.
If you already are a holder of SkyLink 91558-01A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime SkyLink 91558-01A.
However, one of the most important roles played by the user manual is to help in solving problems with SkyLink 91558-01A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device SkyLink 91558-01A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
