Instruction/ maintenance manual of the product B&S 24 (CE) Simplicity
Go to page of 18
09/2007 TP 300-4681-01-IW-SN Intermediate Frame Sno wthr o wer s Form No. 1735249 Briggs & Stratton Yard Power Products Group Copyright © 2007 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved Intermediate Frame Snowthr ower s Mfg.
SLOPE OPERA TION S lopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not operate on it.
Intermediate Frame Snowthr o wers 09/2007 TP 300-4681-01-IW-SN T able of Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. Uncrate . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 4 1 2 Size PSI bar 15 x 5.0-6 20 1,38 16 x 4.8-8 14 ,96 (2) x.
Intermediate Frame Snowthr o wers 09/2007 5 TP 300-4681-01-IW-SN 3 5/16-18 x 2 5/16-18 x 2-3/4 5/16-18 5/16 A C B B A B A 4 5 lb-ft 7 Nm C D D D.
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 6 6 A D C B 5 5/16-18 x 1-1/2 5/16-18 A B A B.
Intermediate Frame Snowthr o wers 09/2007 7 TP 300-4681-01-IW-SN 7 3 2 2 1 8 9 1.
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 8 11 12 10.
Intermediate Frame Snowthr o wers 09/2007 9 TP 300-4681-01-IW-SN 15 13 14 16.
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 10 P erf orm Safety Chec ks Chec k Engine Controls 1. Make sure all safety guards are in place and all nuts, bolts, clips, cotter pins and wires are secure. 2. Check to make sure spark plug wire is attached.
Intermediate Frame Snowthr o wers 09/2007 11 TP 300-4681-01-IW-SN Chec k Snowthr ower Contr ols 1. Check the skid shoes to make sure they are set at the desired height. Adjust if necessary. 2. Check the traction drive control (B, Figure 2). Snowthrower motion should stop when the control is released.
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 12 1.With the drive lever released, the hook (B, Figure 3) should barely touch the lever (C) without raising it. There can be a maximum 1/32” clearance as shown. 2. To adjust, loosen nut (D) by holding the adjusting flats (A) and turning nut (D).
Intermediate Frame Snowthr o wers 09/2007 13 TP 300-4681-01-IW-SN W ARNING Do not over-tighten, as this may cause traction drive to engage without depressing the traction drive control (arm must remain in down position).
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 14 Figure 8 . Skid Shoe Adjustment A. Scraper Bar B. Skid Shoe C. Nuts A B C On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface. On surfaces such as gravel, the scraper bar should be high enough so that it will not pick up gravel or debris.
Intermediate Frame Snowthr o wers 09/2007 15 TP 300-4681-01-IW-SN Figure 9. Belt Cover A. Belt Cover B. Screws A B B Figure 10. Auger Belt Deflection A. Engine Drive Pulley B. Idler Pulley (Engaged Position) C. Auger Drive Pulley D. Nut E. Auger Belt B C A 1/2” (12.
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 16 Belt Replacement A uger Drive Belt The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center.
Intermediate Frame Snowthr o wers 09/2007 17 TP 300-4681-01-IW-SN Figure 17. Frame and Axle Housing Splitting A. Upper Capscrews B. Lower Capscrews C. Auger Housing D. Frame C 9. Remove hair pin (A, Figure 14) and slide rod (B) backward about 3 inches (until shaft separates from the worm drive).
Intermediate Frame Snowthr o wers TP 300-4681-01-IW-SN 09/2007 1 8 17. Slide spout rotator rod (B, Figure 14) into worm gear, and secure with hair pin (A). 18. Install rotator cover (A, Figure 13) and secure with 5/16-18 flange lock nut (B). Tighten nut to 11 lb-ft (15 Nm).
An important point after buying a device Simplicity B&S 24 (CE) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Simplicity B&S 24 (CE) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Simplicity B&S 24 (CE) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Simplicity B&S 24 (CE) you will learn all the available features of the product, as well as information on its operation. The information that you get Simplicity B&S 24 (CE) will certainly help you make a decision on the purchase.
If you already are a holder of Simplicity B&S 24 (CE), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Simplicity B&S 24 (CE).
However, one of the most important roles played by the user manual is to help in solving problems with Simplicity B&S 24 (CE). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Simplicity B&S 24 (CE) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
