Instruction/ maintenance manual of the product 1726794 Simplicity
Go to page of 28
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T riple Catcher Mfg. No. Description 1694499 Clean Sweep Triple Catcher 1726794 Rev. 00 Rev. Date 02/2004 TP 100-4032-00-AT-SN Clean Sweep T riple Catc.
1 Initial Collector Assembl y Assemble Catcher Bags ................................13 Install Cov er ...................................................13 Removing & Re-attac hing the T riple Catcher Removing the Gr ass Catcher ..................
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed.
3 BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.
Initial T urbo Installation 4 50" 44" 35 49 48 7 8 6 4 5 Existing Hardware (Bolt, W asher , Lockw asher , & Nut) 40 41 42 43 22 38 44 1 1 2 3 9 18 18 15 16 17 8 14 13 Existing Pulley & Spacer T orque to 55-70 ft.
Initial T urbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discard the cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5).
Initial T urbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot- tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylock nuts.
Initial T urbo Installation 7 Install Idler Assembl y & Belt Cover 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3.
Initial T urbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 13 & 14) to the support bracket (E) using a 5/16-18 x 1 capscrew (C), washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on the support bracket.
Initial T urbo Installation 9 Mower Dec k Arbor Pulley Mower Dec k T urbo Drive Pulle y T urbo Drive Pulley Idler Pulleys T o Slack en Belt CA UTION Before you begin operating the unit with the Turbo .
Initial Counter Balance & W eight Carrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier Installation A. Washer, 5/16 E. Clips, Safety B. Capscrew, 5/16-18 x 1 F. Carrier, Weight C. Locknut, 5/16-18 G. Holes D.
Initiai Hitch & T ube Installation 11 Figure 1. Install Hitch Plate A. Hitch Plate D. Locknuts, 1/2-13 B. Heat Shield E. Upper & Lower C. Capscrews Hex, Bumper 1/2-13 x 1-1/4 F. Exisitng Holes Figure 3. Install Back Plate A. Back Plate and Support C.
Initial Hitch & T ube Installation 12 Figure 4. Assemble Tubes & Deflector A B G D H K F M L E C A. Deflector B. Back Plate C. Capscrew, 5/16-18 x 1 D. Socket E. Washer, 5/16 F. Locknut, 5/16-18 G. Upper Tube H. Middle Tube I. Lower Tube J. Washer K.
Initial Collector Assembly 13 COLLECT OR ASSEMBL Y Assemble Catcher Ba gs 1. See Figure 1. Insert the wire hoop (H) through the cloth bag (B). 2. Install the clamp (E) and hanger bracket (D). Secure with two 5/16-18 x 3/4 carriage bolts (C), lockwashers (G) and nuts (F).
Removing & Re-attaching Grass Catcher 14 REMOVING & RE-A TT ACHING THE GRASS CA TCHER Removing the Grass Catcher & tubes 1. Remove the hair pin clips (D, Figure 1) and hinge pins (B) and remove the cover (A). 2. Remove the bags (A, Figure 2) by lifting them off their hooks.
Removing and Re-attaching Grass Catcher 15 Figure 8. Install HInge Pins A. Cover C. Hinge B. Hinge Pin D. Hair Pin Clip A B C D Figure 7. Install Cover A. Cover C. Hinges B. Bags A C B Figure 6. Bags A. Bags B. Back Plate A Re-attaching the Grass Catcher 1.
FRONT WEIGHT CARRIER GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 4.
FRONT WEIGHT CARRIER GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 5 Part No Descri p tion Item Qt y Note 1 504908 2 1 MOU NT - WEI GH T CONSUMER Z TWIN & TRIPLE BAGG ER 986507- 01 2 1927557 4 NUT-HEX FL. WHIZ LK. .312-18 3 19 19326 4 WASHER .
TRIPLE CATCHER GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 6.
TRIPLE CATCHER GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 7 Part No Descri p tion Item Qt y Note 1 17 17025 1 COVER ASSEMBLY CONSUMER Z TRIPLE BAGGER 986509 - 01 2 1717082 1 SEAL 3 16 75707 3 TUBE - CLIP GR ASS BAG 4 19 31333 6 CARRIAGE BOLT .
TUBE & HITCH GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 8.
TUBE & HITCH GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 9 Part No Descri p tion Item Qt y Note 1 504915 2 1 LOW ER T UBE CONSUMER Z TRIPLE BAGGER 986506 - 02 2 1960 404 5 SCREW-TRUSS HD. #10-24 X .75 3 19 60096 5 WASHER .
TURBO MOUNTING GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 10.
TURBO MOUNTING GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 11 Part No Descri p tion Item Qt y Note 1 17 13523 1 NUT - SLEEVE . 562-18 x .75 CONSUMER Z TWIN & TRIPLE BAGG ER 986508 - 02 2 16 03592 1 WASHER .88 ID X 1.75 OK X .
TURBO MOUNTING GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 12.
TURBO MOUNTING GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 13 Part No Descri p tion Item Qt y Note 41 1916965 1 LOCKWASHER .375 42 1704768 1 BRACKET - Z 43 1724373 1 BRACKET - L 44 108717 1 SPACER 45 1714817 1 PULLEY - IDLER 2.
16 T orque Specification Chart FOR ST ANDARD MACHINE HARDW ARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc.
An important point after buying a device Simplicity 1726794 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Simplicity 1726794 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Simplicity 1726794 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Simplicity 1726794 you will learn all the available features of the product, as well as information on its operation. The information that you get Simplicity 1726794 will certainly help you make a decision on the purchase.
If you already are a holder of Simplicity 1726794, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Simplicity 1726794.
However, one of the most important roles played by the user manual is to help in solving problems with Simplicity 1726794. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Simplicity 1726794 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
