Instruction/ maintenance manual of the product 1691810 Simplicity
Go to page of 19
OPERATOR’S MANUAL 42”/48” Turbo Blower Assembly Mfg. No: 1691810 Mfg. No. 1691998 FORM 170460604 PRINTED IN U.S.A. 12/93-3ooccI.
HEX CAPSCREW PLAIN WASHER LOCKWASHER a p. NUT HEX CAPSCREW IDENTIFICATION Shown below are actual size hex heads for standard screw sizes. Example: a l/4” screw has a 7116 head and.
Table of Contents Safety Decal ................................ Safety Rules ................................ Installation Lawn Tractor ........................... Front-Cut Rider ......................... Operation .................................. Standard Fastener Identification Chart .
Safety Rules A Read these safety rulesand the safety rules in yo,ur Operator’s Manual and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment.
installation - Lawn ,Tractors NOTE Two spacers are packaged with turbo biower. Installation on tractor requires use of 4-l/16” spacer (see step 11); the 1/2”spacerwill not be used. 1. Remove mower deflector and arbor cover as follows: a. Remove the mower deflector by removing two carriage bolts, lockwashers and nuts.
NOTE Front belt stop should be installed facing outside of deck. ‘6. Install thefront belt stop (A, figure4) onto5/16- 18 x l-1/2 capscrew (installed in step 3) as shown. If removed, reinstall brake spring or spring anchor (F) before flange nut(G). Tighten nut (E) snug only - belt stop will be adjusted in step 8.
10. The baffle (A, figure 7) is installed in the blower housing for use with 42” mower. For use with 48” mower, remove the baffleand install in holes marked 48”. I Figure 7. A Battle NOTE On42”and 48” mowersthecapscrewinstalled in next step is used in the hole occupied by a screw held in place by a retaining nut.
12. Install wing nut (D, figure 9) as follows: a. Remove existing hardware from front end of stone guard. b. From inside deck, install new 5/16-18 x 2-l/4 carriage bolt (F, figure 9). Then install the cup (A), 5/16 lockwasher (6). and 506 nut (C). Tighten the nut.
c. Place mower in low cut position. Raise the flap (A, figure 12) and push on the belt retainer (E) to obtain slack in the belt. Install the blower drive belt (D) in the top groove of the pulley(B). d. Rotate the pivoting cover (A, figure 13) into place and attach the hook (B) to the clip (C) on the housing.
Installation - Front Cut Riders NOTES 1. Two spacers are packaged with the turbo blower. Installation on the Front-Cut Rider requires use of the l/2” spacer (see step 14).
6. Remove the capscrew, lockwasher, and flat washer securing right hand arbor pulley. Retain the washers for reinstallation (step 9). Use a wood block to prevent blade from turning. SunRunnerNanguard Models 6. On early models without bet stop (A, figure 3) remove two self-tapping screws from arbor and install two .
9. Slip the mower drive belt (A, figure 5) around the bottom groove of double-groove pulley (B). Install pulley with hub down and secure with new 7/l 6-14 x 2-l /4” capscrew (C) and washers (D and E) removed in step 5. Make sure splines arecorrectlyalignedand torquecapscrewto55- 60 ft.
13. Install the new baffle (A, figure 8) in deck on stone guard using existing hardware. Hardware may be installed with nut to inside or nut to outside. 14. On new arbor cover, install on top of weld bolt (A, figure 9) the largest washer (B l-i/Z” O.
16. Make sure that flat washer (F, figure 9) is on top of spacer assembly and install new arbor belt cover (A, figure 10) as shown in figure 10. Secure with flat washer (l-1/4” O.D.) and locknut (8). Belt cover should be free to pivot. 17. Install the blower assembly as follows: a.
Operation A WARNING For safety reasons, grass and debris should not be removed from any part of turbo or collection system until engine is shut off, key removed, and all moving parts have stopped. I A I WARNING Before raising cart or twin-bag cover, shut off engine, remove key, and set parking brake.
.
i.
.:::).‘,:,:::: ~._,, ,.
..:,, ::: TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE +200/o SIZE 8-32 8-36 lo-24 lo-32 l/4-20 l/4-28 5116-18 5116-24 318-16 318-24 7116-14 7116-20 l/2-13 112-20 9116-12 9116-18 518-11 518-18 314-10 3/4-16 718-g 718-14 1-8 1-12 SAE GRADE #2 SAE GRADE A15 SAE GRADE #8 0 Q 8.
An important point after buying a device Simplicity 1691810 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Simplicity 1691810 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Simplicity 1691810 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Simplicity 1691810 you will learn all the available features of the product, as well as information on its operation. The information that you get Simplicity 1691810 will certainly help you make a decision on the purchase.
If you already are a holder of Simplicity 1691810, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Simplicity 1691810.
However, one of the most important roles played by the user manual is to help in solving problems with Simplicity 1691810. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Simplicity 1691810 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
