Instruction/ maintenance manual of the product SVD 500 PLUS Sim2
Go to page of 44
VIDEO PROJECT OR USER AND INST ALLA TION MANUAL MANUALE D’USO E INST ALLAZIONE SVD 500 PLUS SVP 450 PLUS SVP 420 HB.
INDEX 1- W ARNINGS ......................................................................................... Page 3 1.1 Safety and Regulations ............................................................. 4 2- GENERAL INFORMA TION ....................
SVP 450 PLUS - SVD 500 PLUS 2 5- THE COMPLETE FUNCTION RC 3000 REMOTE CONTROL .......... Page 24 5.1 Complete function RC3000 remote control ............................... 24 5.2 Batteries .............................................................
SVP 450 PLUS - SVD 500 PLUS 3 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 1 W ARNINGS T o reduce the risk of electric shock, disconnect the power supply cable before opening the equipment There are no parts inside the projector that need adjusting by the user .
SVP 450 PLUS - SVD 500 PLUS 4 2.1 Projector Identification The model and serial number are located on the projector ’s rear label Fig. 1 . Record the serial number in the space below and quote it each time you ask for information or technical assistance from Multimedia SP A.
SVP 450 PLUS - SVD 500 PLUS 5 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH - Do not attempt to use it as it could be dangerous or even worsen the damage. - If the projector is not used for long periods of time or during storms, unplug the projector temporarily from the mains to avoid damaging the projector caused by lightning or temporary overcurrents.
SVP 450 PLUS - SVD 500 PLUS 6 2.5 Cleaning the projector When we speak about projector cleaning we mean the outside of it. NO internal cleaning is necessary . - Before you start cleaning the projector take the plug out of the mains. - Do not use liquid or spray detergents.
SVP 450 PLUS - SVD 500 PLUS 7 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH • • • • • THE FOLLOWING FUNCTIONS ARE ON THE P ANEL: 1- Power switch. 2- Fuse holder . The fuse type is 5A, T delayed. Attention: For continued protection against the risk of fire, replace only with one of the same type and rating.
SVP 450 PLUS - SVD 500 PLUS 8 3 USER REMOTE CONTROL RC 3100 RC 3100 is the User Remote Control for normal programme selection and analogue adjustments (once the projector is installed). The projector is controlled by the infrared ray remote control (I.
SVP 450 PLUS - SVD 500 PLUS 9 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 3.2 RC 3100 User Remote Control Read this chapter through carefully before altering any values or making any adjustments.
SVP 450 PLUS - SVD 500 PLUS 10 NORMAL Each time this button is pressed, a different adjustment will be selected, sequentially . Use the arrows to change the value, press MEMO to store the new value. Press ESC to exit. 3.7 Screen format selection T o select the correct screen format: ( NORMAL, SMALL, 16/9, LETTER BOX, CINEMA, ).
SVP 450 PLUS - SVD 500 PLUS 11 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 3.10 Muting video button Press MUTE for about 2 seconds. The picture will darken while the projector stays on; the picture will reappear immediately if you press the button again. 3.
SVP 450 PLUS - SVD 500 PLUS 12 VIDEO MENU NOISE RED. STD SELEC. BLANKING WHITE BALANCE UPC MENU TL V SYNC BLANKING H. = 00 V . = 00 Use the arrows to select TL V SYNC and press ENTER to confirm, the second menu appears: Use the arrows for function selection.
SVP 450 PLUS - SVD 500 PLUS 13 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH VIDEO MENU NOISE RED. STD SELEC. BLANKING WHITE BALANCE UPC MENU TL V SYNC UPC ON PROGRESSIVE LINE INSERT FIELD INSERT MAIN SETTINGS MEMO NOR DA T A INST ALL. MENU MAIN SETTINGS STORED MEMO NOR DA T A INST ALL.
SVP 450 PLUS - SVD 500 PLUS 14 CON 49 STORED MAIN SETTINGS MEMO NOR DA T A INST ALL. MENU CON 49 INST ALL MODE Before adj. REGISTRA TIONS be sure the following items have been checked : 1 Mechanical centering of the projector and tubes 2 Lens focus adjustment All peaking, hue, colour , brightness and contrast values are now stored.
SVP 450 PLUS - SVD 500 PLUS 15 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH T o remove the top cover completely you must unscrew the two locking screws ( B ) close to the two pivots and the other two ( C ) securing the jointed rod to the cover . B C A 4.2.
SVP 450 PLUS - SVD 500 PLUS 16 - Measure the screen diagonal and take the nearest value from the table. - Calculate the ratio between the table value and the relative width. - Multiply the value obtained by the actual screen width. Example: Suppose we have a 105” screen diagonal.
SVP 450 PLUS - SVD 500 PLUS 17 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH - If the measurement of the screen diagonal is not in the table, C can be determined (in cm) as follows. - Measure the screen diagonal and take the nearest value from the table. - Calculate the ratio between value C and screen width in the table.
SVP 450 PLUS - SVD 500 PLUS 18 SCREEN SIZE D Useful area 4/3 Diagonal Width Height (Inches) (cm.) (cm.) (cm.) 60” 121,9 91,4 204 80” 165,5 124,9 263 90” 182,9 137,2 283 100” 203,2 152,4 322 12.
SVP 450 PLUS - SVD 500 PLUS 19 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH A B 4.5.1. Spacers changing T o change the spacers first of all remove the top cover and front panel. Now slightly loosen the 4 screws ( A ) for each tube, change the spacers ( B ) ( see the spacers table ) and then tighten the screws.
SVP 450 PLUS - SVD 500 PLUS 20 1 0,5 0,2 0,5 0,2 0,5 0,2 0 0,2 00 1 0,5 0,2 0,2 0 11 1 1 0,2 0,2 1 0 0,2 00 1 0,2 0 1 0 0,2 1 00 1 0,3 0,2 0,2 0,2 0,2 1 1 0,3 1 0,2 0 150" GREEN BLUE RED 1 0 0,3 .
SVP 450 PLUS - SVD 500 PLUS 21 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 4.6 Projector centering The first step towards a good installation is centering the projector with respect to the screen.
SVP 450 PLUS - SVD 500 PLUS 22 B A 4.8 Lens focus adjustment Each lens must be focused individually with the tubes on, one at a time and following this procedure: 1. Select the HA TCH test pattern by pressing the TEST button on the remote control. An external pattern signal can be used if you prefer .
SVP 450 PLUS - SVD 500 PLUS 23 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 9. Use the yoke rings (centering magnets A and B) to shift the green tube image onthe centre of the screen reference point.
SVP 450 PLUS - SVD 500 PLUS 24 Selects one of the available screen formats (Small, Nor- mal, Wide, Cinema, Letter Box) Selects the right input directly. Confirms current choice or goes to the next page in the current menu. Returns to the previous menu or page.
SVP 450 PLUS - SVD 500 PLUS 25 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH VIDEO SETUP Y/C DELA Y WHITE BALANCE COMB. FIL TER GAMMA ADJ. ADAPTIVE BLACK BLUE STRETCH 5.
SVP 450 PLUS - SVD 500 PLUS 26 5.4.2 T o switch on/off the Comb filter , you have to enter in installation mode. Press VID.S the following menu will appear: VIDEO SETUP Y/C DELA Y WHITE BALANCE COMB. FIL TER GAMMA ADJ. ADAPTIVE BLACK BLUE STRETCH VIDEO SETUP COMB FIL TER ON Use the arrow or to select the comb filter and press ENTER to confirm.
SVP 450 PLUS - SVD 500 PLUS 27 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH HHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHH HHHH.
SVP 450 PLUS - SVD 500 PLUS 28 WHITE BALANCE SET TO SET TO SET TO SET TO 3200K 6500K 9300K USER STORED 3200K ADJ BLACK XX XX XX R G B WHITE XX XX XX STORE DA T A ? 5.7 White balance T o select one of the set colour temperatures (3200 ° K,6500 ° K, 9300 ° K, USER BANK) for the projected images.
SVP 450 PLUS - SVD 500 PLUS 29 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH The name is a mnemonic label and it is written by the user . The aspect ratio flag indicates which aspect ratio has been stored by the user during the regulations setup. It is very important for the user to store the correct aspect ratio flag.
SVP 450 PLUS - SVD 500 PLUS 30 5.8.5 How to store a new input signal T o store a new input signal in a memory bank press MEMO and you will enter the MEMOR Y MANAGER mode. The following menu will appear: MEMORY MANAGER Copy from ? LOAD COPY BN NAME F HOR VER 01 Pal Upc .
SVP 450 PLUS - SVD 500 PLUS 31 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH Copy from 05 to ? Copy from 05 to 09 ? MEMORY MANAGER Modify bank name LOAD COPY BN NAME F HOR VER 01 Pal Upc . . . . . Pup 16/9 Nstc..... NstcUpc V ga 2 Vga 3 N 31.2 50 02 -- - . - --- 03 W 31.
SVP 450 PLUS - SVD 500 PLUS 32 Done OPTIONS MENU OSD INST ALL. TYPE POWER ON VCR ST ABILITY MEMORIY MANAGER WORKING TIME INST ALL. TYPE DESKTOP FRONT DESKTOP REAR CEILING FRONT CEILING REAR OPTIONS MENU OSD INST ALL. TYPE POWER ON VCR ST ABILITY MEMORY MANAGER WORKING TIME OPTIONS MENU INST ALL.
SVP 450 PLUS - SVD 500 PLUS 33 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH POWER ON ST AND BY SWITCH ON OPTIONS MENU INST ALL. TYPE MEMORY MANAGER OSD POWER ON VCR ST ABILITY WORKING TIME OPTIONS MENU VCR ST ABILITY ON DEFL CENT H. = 62 V . = 50 - PICTURE - RASTER T o switch on or off the VCR stability , you must enter the installation mode.
SVP 450 PLUS - SVD 500 PLUS 34 - PICTURE - DEFL SIZE H. = 100 V . = 100 DEFL PIN TOP H. = 50 V . = 50 DEFL KEY H. = 50 Use the arrow or to change horizontal linearity . Use the arrow or to change vertical linearity . Press ENTER or EXIT to change function.
SVP 450 PLUS - SVD 500 PLUS 35 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH CONV CENT CRT : RGB ADJ : R . . H. = 52 V . = 50 b b a a CONV LIN CRT : RGB ADJ : R . . H. = 45 V . = 50 5.13.1 Central convergence This function allows to overlap the blue and red images on the green one, at the centre of the screen.
SVP 450 PLUS - SVD 500 PLUS 36 5.13.6 Horizontal keystone adjustment This function allows to overlap the red and blue horizontal lines on the green ones. CONV KEY CRT : RGB ADJ : R . . V . = 50 Use the arrow or to set in line the horizontal lines of the image with the screen borders.
SVP 450 PLUS - SVD 500 PLUS 37 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 5.15 Screen corners corrections Upon pressing the ENTER button, you enter the corner adjustment menu, the folowing image will appear . H. = 50 V . = 60 ZONE CRT : RGB ADJ / R . . + + + + Press EXIT or ENTER to change.
SVP 450 PLUS - SVD 500 PLUS 38 6 TECHNICAL SPECIFICA TIONS 6.1 Projection system - 3 picture tubes, 3 lenses - Horizontal line system - Lenses : Hybrid lenses (SVP 450 PLUS) High definition glass lenses (SVP 500 PLUS-HD) 6.2 Projection tube - 7” monochrone tube, high brightness, liquid cooling, air lenses coupling, electrostatic focusing.
SVP 450 PLUS - SVD 500 PLUS 39 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 7 DISPLA Y PERFORMANCES 7.1 Flyback time - Horizontal 5,4 µs tip. - V ertical 500 µs tip. - R,G,B band width: 20 MHz, -3dB typical. - Standard video band width: 5.5 Mhz, -3dB typical - Contrast range: more than 100:1 - W arm up time (suggested): 20 minutes 7.
SVP 450 PLUS - SVD 500 PLUS 40 7.8 Scart connector - Pin 5 Earth B - Pin 7 Input B 0.7 Vpp, termination 75 - Pin 9 Earth G - Pin 1 1 Input G 0.7 Vpp, termination 75 - Pin 13 Earth R 0.
SVP 450 PLUS - SVD 500 PLUS 41 ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH 12 TROUBLESHOOTING The LED lights on the rear panel shows the projector status. LED Lights MEANING ON indicator Red light Stand-b.
SVP 450 PLUS - SVD 500 PLUS 42 13 ANWEISUNGEN AUF DEUTSCH ACHTUNG: Ö FFNEN SIE NICHT UND NEHMEN SIE NIEMALS DIE HAUBE DES PROJEKTORS AB WEIL DARUNTER GEF AHRLICHE HOCHSP ANNUNGEN, BIS 33 KVOL T , ANLIEGEN. WENN ERFORDERLICH, RUFEN SIE IMMER EINEN TECHNIKER.
SIM2 Multimedia S.p.a. • V .le Lino Zanussi, 1 1 • I-33170 Pordenone • Phone +39.434.383.253-256 • Fax +39.434.383260-261 • http://www .sim2.it • e-mail: info@sim2.it cod. 46.9220.302 • Due to the constant product development, specifications and design might be subject to change without notice.
An important point after buying a device Sim2 SVD 500 PLUS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sim2 SVD 500 PLUS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sim2 SVD 500 PLUS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sim2 SVD 500 PLUS you will learn all the available features of the product, as well as information on its operation. The information that you get Sim2 SVD 500 PLUS will certainly help you make a decision on the purchase.
If you already are a holder of Sim2 SVD 500 PLUS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sim2 SVD 500 PLUS.
However, one of the most important roles played by the user manual is to help in solving problems with Sim2 SVD 500 PLUS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sim2 SVD 500 PLUS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
