Instruction/ maintenance manual of the product AX-5103 Sherwood
Go to page of 13
Caution regarding placement (Except for U.S.A. and Canada) To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below.
3 READ THIS BEFORE OPERA TING Y OUR UNIT Units shipped to the U.S.A and Canada are designed for operation on 120 Volts AC only. Observe all safety precaution for use of a polarized AC plug. However, some products may be supplied with a non polarized plug.
4 CONTENTS Introduction • UNPACKING AND INSTALLATION | 2 • READ THIS BEFORE OPERATING YOUR UNIT | 3 System Connections | 5 Front Panel Controls | 7 DIGI LINK III System Remote Controls | 8 • REM.
5 ENGLISH AC OUTLET 230V~50Hz SWITCHED 100W(0.43A) MAX. AC INPUT 230V~50Hz 190W PHONO CD TUNER TAPE 1 /MD IN OUT IN OUT TAPE 2 MONITOR DIGI LINK SPEAKER A SPEAKER B AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
6 AC OUTLET 230V~50Hz SWITCHED 100W(0.43A) MAX. AC INPUT 230V~50Hz 190W PHONO CD TUNER TAPE 1 /MD IN OUT IN OUT TAPE 2 MONITOR DIGI LINK SPEAKER A SPEAKER B AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR. WARNING : SHOCK HAZARD-DO NOT OPEN. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
BALANCE CONTROL KNOB Adjust the stereo balance between left and right speakers. • The center position is the normal condition. TONE DIRECT SWITCH Press this switch to bypass the tone (bass and treble) circuitry for pure sound.
8 DIGI LINK III System Remote Controls • You can remotely control not only this amplifier but also Sherwood compatible components bearing the DIGI LINK II or III logo . • For system remote control operation, first make the DIGI LINK connections. • In the DIGI LINK III remote control system, if pressing PLAY, etc.
REMO TE CONTROL OPERA TION RANGE 9 LO ADING B A TTERIES Remove the cover. 1 Load two batteries matching the polarity. 2 • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor.
Operations LISTENING T O A PROGRAM SOUR CE 10 Before operation In the standby mode, turn the power on. 1 Select the desired input source. 3 Switch the desired speakers on.
11 Operate the selected component for playback. 4 Adjust the volume to a comfortable listening level. 5 To emphasize the sound of frequencies that are difficult to hear at low volume levels. 8 To listen to a program source without the tone effect. 9 Adjust the tone (bass and treble).
12 RECORDING Select the desired input as recording source except for TAPE 1/MD and TAPE 2 MONITOR. 1 Select the desired input as recording source except for TAPE 2 MONITOR. 1 Start recording on the tape deck or the MD recorder connected to TAPE 1/MD. 2 Set the TAPE 2 MONITOR button to on.
13 T roubleshooting Guide If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or our service organization.
14 Specifications • Power output, 8 Ω , THD 0.3 %, 40 Hz 20 kHz | 2 X 100 W • Total harmonic distortion, 8 Ω , 100 W, 1 kHz | 0.03 % • Intermodulation distortion 60 Hz : 7 kHz = 4 : 1 SMPTE, 8 Ω , 100 W | 0.05 % • Input sensitivity, 47 k Ω PHONO (MM) | 3.
An important point after buying a device Sherwood AX-5103 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sherwood AX-5103 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sherwood AX-5103 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sherwood AX-5103 you will learn all the available features of the product, as well as information on its operation. The information that you get Sherwood AX-5103 will certainly help you make a decision on the purchase.
If you already are a holder of Sherwood AX-5103, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sherwood AX-5103.
However, one of the most important roles played by the user manual is to help in solving problems with Sherwood AX-5103. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sherwood AX-5103 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
