Instruction/ maintenance manual of the product TL-M4600 Sharp
Go to page of 41
MODEL TL-M5200 TL-M4600 LCD MONIT OR RS-232C Specifications and Commands .......... 2 Setting up the Monitor Network En vir onment .... 10 1. Connecting the Monitor to a Computer ............ 1 1 2. Setting an IP Address for the Computer .......... 12 3.
-2 Computer contr ol A computer can be used to control the monitor by connecting an RS-232C serial control cable (cross type, commerciall y available) to the monitor . (See page 20 of the monitor’ s operation manual f or connection.) Communication conditions Set the serial port settings of the computer to match that of the table.
-3 Commands Example: When turning on the monitor , make the follo wing setting. → ← PO W R _ 1 __ OK Monitor Computer Normal(Computer) Full Dot By Dot(Computer) / Normal(Video) S.
-4 RS-232C Specifications and Commands Normal (Computer) Full Dot By Dot(Computer) / Normal(Video) S.Stretch(Video) Cinema16:9(Video) Cinema14:9(Video) Zoom14:9(Video) Normal(Computer) Full Dot By Dot(Computer) / Normal(Video) S.
-5 RS-232C Specifications and Commands Standard Presentation Movie Game sRGB Off On On(Display) -16 – +16 0 – +40 -30 – +30 -30 – +30 -30 – +30 -10 – +10 -30 – +30 -30 – +30 -30 – +3.
-6 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN HDMI INPUT S-VIDEO INPUT AV Mode OPC Backlight Contrast Bright Color Tint Sharpn.
-7 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN VIDEO INPUT Position Fine Sync RGB Frequency Check HDMI Setup Audio Audio Out St.
-8 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN Video System Background Selection LED Power On Delay Picture Flip Keylock Set Inputs Input Label Language Master& Slave P&P (Split-screen) AUTO PAL SECAM NTSC4.
-9 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (Mode 1, Mode 2) COMMAND PARAMETER RETURN P&P Main Select ALL Reset Sleep Timer Multi Screen *3 Left *2 Right *2 Sleep.
-10 Pag e 1 1 1. Connecting the monitor to a computer Setting up the Monitor Network Environment This section describes the basic procedure for using the monitor via the network. If the network is alread y constructed, the monitor’ s network settings may need to be c hang ed.
-11 Setting up the Monitor Network Environment 1. Connecting the Moni- tor to a Computer Establishing a one-to-one connection from the monitor to a computer . Using a LAN cable (Cat- egory 5, cross-over type) you can configure the monitor via the computer .
-12 1 2 1 XXXXXXXXX 1 2 Setting up the Monitor Network Environment 2. Setting an IP Address for the Computer The following describes how to make settings in Windo ws Vista ® . 1 Log on the network using the administrator’ s account for the computer .
-13 Setting up the Monitor Network Environment 1 2 5 Click “Internet Protocol V ersion 4 (TCP/IPv4)”, and click the “Properties” button. 6 Confirm or change an IP address f or the setup computer . 1 Confirm and note the current IP ad- dress, Subnet mask and Default gatewa y .
-14 Setting up the Monitor Network Environment 3. Setting up a Network Connection for the Monitor Settings for suc h items as the monitor’ s IP ad- dress and subnet mask are compatible with the existing network. Set each item on the monitor as follows.
-15 4 The TCP/IP setting screen ap- pears, ready for network settings f or the monitor . Note • Confirm the existing network’ s segment (IP address group) to avoid setting an IP ad- dress that duplicates the IP addresses of other network equipment or computers.
-16 Controlling the Monitor via LAN Controlling the Monitor Using Internet Explorer (Version 5.0 o r later) Complete connections to external equipment before starting the operation. (See pages 16- 20 of the monitor’ s operation manual.) Complete the A C cord connection.
-17 Confirming the Monitor Status (Status) On this screen, you can confirm the monitor status. Y ou can confirm the follo wing items : • • • • • MA C Address • • • • • Power • .
-18 Controlling the Monitor via LAN Setting and Adjusting the Monitor (Settings & Adjustments ) Example: “Picture” screen display for COMPUTER On these screens, you can make monitor set- tings or adjust ments.
-19 Controlling the Monitor via LAN Making General Settings for the Network (Network - General) On this screen, you can make general settings relating to the network. After clic king the “Apply” button, the set val- ues appear . Confirm that the v alues are set properl y , and then c lick the “Confirm” but- ton.
-20 Controlling the Monitor via LAN Set ting Error Items and Destination Addresses to which E - m ail is to be Sent when an Error Occurs (Mail – Recipient Settings) On this screen, you can input e-mail destina- tions to which err or notification (error items) e-mails are sent.
-21 Setting up the Monitor Using RS-232C or T elnet When Connecting Using RS-232C 1 Launch general purpose terminal emulator . 2 Input settings for the RS-232C port of the terminal em ulator as follows. Baud Rate : 9600 bps* Data Length : 8 bit Parity Bit : None Stop Bit : 1 bit Flow Control : None * This is the f actor y default setting.
-22 When Connecting Using Telnet 1 Click “Star t” from the Windows ® desk- top and select “Run”. 2 Enter “telnet 192.168.150.2” in the text box that opens up. (If the IP address of the monitor i s 192.168.150.2.) 3 Click the “OK” button.
-23 SETUP MENU (Main Menu) [1] IP Address IP address settings. (P age 26 ) [2] Subnet Mask Subnet mask settings. (P age 26 ) [3] Default Gateway Def ault gatewa y settings. (Page 26 ) [4] User Name (Factory default setting : Not Re- quired) Setting of user name f or secur ity protection.
-24 View Setting Detail List ([V]View All Setting) 1 1 1 1 1 Enter “v” and press the “Enter” key . Display all setting values(*). Enter number or symbol of item to be selected on the SETUP MENU . When setting, input the details to be set. Setting is carried out one item at a time, and saved at the end.
-25 Save Settings and Quit ([S]Save & Quit) Save set values and quit menu. 1 1 1 1 1 Enter “s” and press the “Enter” key . 2 2 2 2 2 Enter “y” and press the “Enter” key .
-26 IP Address Setting ([1]IP Address) Setting of IP address. 1 1 1 1 1 Enter “1” and press the “Enter” key . 2 2 2 2 2 Enter numerical value to be set and press the “Enter” key . Display IP address after change (*). Subnet Mask Setting ([2]Subnet Mask) Setting subnet mask.
-27 Password Setting ([5]Password) Carrying out security protection using password. 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter passw ord and press the “Enter” key . Displa y set password (*). Note • Password can be up to 8 characters.
-28 Disconnecting All Connec- tions ([D]Disconnect All) It is possible to disconnect all the TCP/IP connec- tions currently recognized b y the monitor . Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection.
-29 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the monitor and a computer etc. is working normally . 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter IP address of device to be tested and press the “Enter” key .
-30 Setting of Search Port (ADVANCED[0]Search Port) Sets the port number used when searching for the monitor from the network. 1 1 1 1 1 Enter “0” and press the “Enter” key . 2 2 2 2 2 Enter numerical v alue and press the “Enter” key . Display set numerical value (*).
-31 Multi Screen Projection Info • Bef ore setting up the multi screen projection, install Internet Explorer (version 5.0 or later). • Image quality may deteriorate when picture signals are input through multiple monitors with an RGB cable in connection.
-32 Multi Screen Projection Setting up the Multi Screen Projection Input Signal Following is an e xample of how to use 4 monitors. Video equipment Monitor 1 Computer RGB cable MONIT OR OUT terminal MO.
-33 Multi Screen Projection 1 Access one of the four monitors via Internet Explorer . (See “Controlling the Moniotor Using Internet Explorer (V ersion 5.0 or later)” (page 16 ) f or the details.) 2 Click “Multi Screen” on the menu. • “Multi Screen” display will appear .
-34 Multi Screen Projection Notes on the Wide Multi Screen Projection Selecting “2 X 1”, “3 X 1”or “4 X 1” on “Status” (see page 33 ) allows you to create the wide m ulti screen.
-35 Multi Screen Projection LAN terminal LAN cable (str aight-through type) Hub LAN terminal LAN terminal LAN terminal Computer LAN cable Setting up the Multi Screen Projection Controlling When y ou w.
-36 Multi Screen Projection Monitor 1 : Master Monitor 3 : Slave Monitor 2 : Slave Monitor 4 : Slave Computer LAN cable Hub LAN terminal LAN terminal LAN terminal LAN terminal LAN cable (straight-through type) 1 Change the TCP/IP settings for the computer as shown belo w .
-37 Multi Screen Projection 4 T urn on all of the monitors. 5 Access the monitor 1 from the com- puter via Internet Explorer . (See “Controlling the Monitor Using Internet Explorer (V ersion 5.0 or later)” on page 16 fo r the details.) 6 Click “Master & Slave” on the menu.
-38 Multi Screen Projection Master Set Inputs ON ON OFF OFF OFF ON ON OFF OFF OFF OFF ON COMPUTER 1 COMPUTER 2 DV I HDMI VIDEO S-VIDEO Slave Set Inputs COMPUTER 1 COMPUTER 2 DV I HDMI VIDEO S-VIDEO Monitor 1 Monitor 2-4 13 Repeat the same procedure fr om the step 10 to 12 for the monitor 3 and 4.
-39 Comm unication cannot be established with the monitor When connecting the monitor using serial-connection Check that the RS-232C terminal of the monitor and a computer or the commercially available controller are connected correctly . Check that the RS-232C cab le is a cross-over cab le.
-40 Tr oubleshooting Ta ke the follo wing steps for chec king the network settings for the computer . 1. Open a command prompt. • In the case of Windows ® 2000: click “start” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order .
-41 Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also , check if an IP address is set. 1. Open a command prompt. • In the case of Windows ® 2000: click “start” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order .
An important point after buying a device Sharp TL-M4600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sharp TL-M4600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sharp TL-M4600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sharp TL-M4600 you will learn all the available features of the product, as well as information on its operation. The information that you get Sharp TL-M4600 will certainly help you make a decision on the purchase.
If you already are a holder of Sharp TL-M4600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sharp TL-M4600.
However, one of the most important roles played by the user manual is to help in solving problems with Sharp TL-M4600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sharp TL-M4600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
