Instruction/ maintenance manual of the product RK-12S30 Sharp
Go to page of 8
1 PA RT NAME EXHAUST DUCT BACK PDVC-B107WRWZ EXHAUST DUCT UPPER PDVC-B105WRWZ DIVIDE PLA TE L PSKR-A486WRWZ DIVIDE PLA TE R PSKR-A487WRWZ RECTIFIER PLA TE L PSKR-A484WRWZ EXHAUST DUCT LEFT PDVC-B108WR.
2 PREP ARA TION Follow the directions from 1 to 5 to attach cushions to some parts. 1. EXHAUST DUCT UPPER Remove the backing paper from each CUSHION 1 . Attach the CUSHIONS 1 to each side flange of the EXHAUST DUCT UPPER as shown in the illustration below .
3 3. EXHAUST DUCT BOTTOM Remove the backing paper from CUSHION 3 . Attach the CUSHION 3 to the EXHAUST DUCT BOTTOM as shown in the Illustration below . * Start A to attach the CUSHION 3 . 4. DIVIDE PLA TE L Remove the backing paper from CUSHION 4 . Attach the CUSHION 4 to the DIVIDE PLA TE L as shown in the Illustration below .
4 STEP 1: CABINET OR W ALL OPENING Provide an opening in the wall or cabinet shown in Figure 1 . The depth should be minimum 23 1 / 4 " (590.5 mm). The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (about 150 lbs.
5 STEP 3: EXHAUST DUCT BOTTOM INST ALLA TION 1 Place the oven onto the EXHAUST DUCT BOTTOM, lowering the 4 feet of the oven onto the projections at the 4 corners of EXHAUST DUCT BOTTOM as shown in Figure 3-A.
6 STEP 5: INST ALLA TION OF REAR SP ACER and EXHAUST DUCT UPPER 1 Attach RECTIFIER PLA TE L to inside of EXHAUST DUCT UPPER with 4 SCREWS (A) as shown in Figure 5-A. 2 Place EXHAUST DUCT UPPER over the oven and EXHAUST DUCT BACK, and attach REAR SP ACER with 2 SCREWS (A) in Figure 5-B.
7 STEP 8: OVEN INST ALLA TION CAUTION: Never hold the handle when moving the oven. T wo persons are required to install the oven. 1 Establish center line of opening and mark front edge. 2 Place the oven on a table or stand positioned in front of the cabinet where the oven is to be installed.
8 4 Secure EXHAUST DUCT BOTTOM to the shelf with 2 SCREWS (B) as shown in Figures 8-B. STEP 9: FRAME ASSEMBL Y INST ALLA TION 1 Attach FRAME ASSEMBL Y and tighten 4 SCREWS (C) as shown in Figure 9 and Figure 9-A. Pull bottom panel of FRAME ASSEMBL Y toward you to remove or replace the drip tray .
An important point after buying a device Sharp RK-12S30 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sharp RK-12S30 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sharp RK-12S30 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sharp RK-12S30 you will learn all the available features of the product, as well as information on its operation. The information that you get Sharp RK-12S30 will certainly help you make a decision on the purchase.
If you already are a holder of Sharp RK-12S30, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sharp RK-12S30.
However, one of the most important roles played by the user manual is to help in solving problems with Sharp RK-12S30. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sharp RK-12S30 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
