Instruction/ maintenance manual of the product HTSB250 Sharp
Go to page of 16
ENGLISH MODEL HT -SB250(BK) SOUND BAR SYSTEM OPERA TION MANUAL B arcodesof t http://www.barcodesoft.com Barcode Symbology: Code 93 ; Font Facenam e: Code93 M H r Data To Encode: TINSZA877AWZZ Point Si.
E-1 Special notes W ARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CO VER (OR B ACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SER VICING TO QU ALIFIED SERVICE PERSONNEL.
E-2 IMPORT ANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety .
E-3 IMPORT ANT SAFETY INSTRUCTIONS (continued) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructio.
E-4 For U.S. customer only CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when ship in its or.
E-5 V olume control ■ The soun d level at a given volum e settin g depend s on unit efficiency , location, and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on with the vol ume control setting up high, or while continually listening at high volumes.
E-6 1 10 9 1 1 14 15 12 1 3 3 2 4 5 7 6 8 Audio Line In 2 Jack ................................. 9 Line In 1 Jacks ....................................
E-7 System preparation Make sure to unplug the AC power cord before installing the unit or changing the position. Select from three installation methods according to the preferred position. Using spikes Nuts (secured on spikes) must be used when installing spikes.
E-8 Fix a wall mount plug into the hole using a hammer, until it is ush with the wall surface. 3 1-1/4” (32 mm) 3/8” (8-9 mm) W all surface S y s t e m p r ep a r a t io n ( c o n t i n u e d ) W all surface Screw the wall mount angle to the wall as shown in the illustration.
E-9 Falling prevention Safety wires (not suppl ied) are usef ul to prevent the unit from falling off the table. Loop the safety wires (not supplied) into each hole as shown and tie the safety wires to the LCD TV stand. Sound bar connections to TVs Caution: Turn off all other equipment before making any connections.
E-10 AC power connection Aft er che cki ng al l the con ne cti ons have bee n mad e correctly , connect the AC power cord to the AC power input jack, then to the AC outlet. Using with the AC/DC adaptor ■ 1 Plug the AC power cord into the AC/DC adaptor .
E-1 1 shall not be exposed to excessive heat such as sunshine, re or the like. Installing the battery incorrectly may cause the unit to malfunction. Notes concerning use: Replace the battery if the operating distance is reduced or if the operation becomes erratic.
E-12 General control (continued) Muting ■ The volume is muted temporarily when pressing the MUTE button on the remote cont rol. Pres s again to restore the volume. Preset sound mode ■ Main unit operation: T o change to a different mode, press the SURROUND button repeatedly until the desired sound mode lights up.
E-13 Symptom Possible cause No sound is heard. Is the input signal (selection) set properly? Is the volume level set to “0”? Is muting activated? ● ● ● Noise is heard during playback. Move the unit away from any computers or mobile phones. ● When a button is pressed, the unit does not respond.
E-14 T roubleshooting chart (continued) Condensation ■ Sudden temperature changes, storage or ope rat ion in an extr eme ly hu mid envir onm ent may cause condensation inside the cabinet or on the transmitter on the remote control. Conden sation can cause the unit to ma lfunc- tion.
E-15 Specications As part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement without prior notice. The performance specica- tion gures indicated are nominal values of production unit.
An important point after buying a device Sharp HTSB250 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sharp HTSB250 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sharp HTSB250 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sharp HTSB250 you will learn all the available features of the product, as well as information on its operation. The information that you get Sharp HTSB250 will certainly help you make a decision on the purchase.
If you already are a holder of Sharp HTSB250, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sharp HTSB250.
However, one of the most important roles played by the user manual is to help in solving problems with Sharp HTSB250. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sharp HTSB250 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center