Instruction/ maintenance manual of the product 201 Seiko
Go to page of 42
Customer Display DM-D500 Installation Manual 401156101.
CAUTIONS ❏ This document shall apply only to the product(s) identified herein. ❏ No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.
1 Engli s h Safety Precautions This document presents important information intended to ensure safe and effective use of this product. Please read this doc ument carefully, and store i t in an acc essible locatio n near your installation. Precaution Headings This document uses the two headings shown below to call attention to potential hazards.
2 CAUTION: ❏ Do not plug t he cable differently fr om the instruction in this manual. Wrong connection may cause equipment damage and fire. ❏ Be sure to set this equipment on a firm, stable, horizontal sur face. Product may be damaged or cause injury if it falls.
3 Engli s h WARNING You are cautioned that chan ges or modification s not ex press ly approved by SEIKO EPSON Co rporation could void your authority to operate the equipment.
4 Contents About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Engli s h This manual explains how to set up the DM-D500. Unpacking The following items are in the box. Make sure that you have all the items shown above, and that none has been damaged. If you find anything missing or damaged items, pleas e contact your DM- D500 dealer.
6 Usage The DM-D500 can be used with the following equiment. ❏ IR Series . You can attach the DM-D500 to the IR Series using the “ DM-D pole unit for IR ” (DP-504). (See page 8.) ❏ TM-H5000II/TM-J8000 printers . You can attach the DM-D500 to TM-H5000II/TM- J8000 printers using the “ DM-D pole unit for TM printers (Type B) ” (DP- 503).
7 Engli s h Precautions when connecting to a TM printer When the DM-D500 is connected to a TM printe r, be sure to check the serial number on th e label affixed to t he rear or bottom of t he TM printer. If the serial number is one of th e numbers indicated below it can be us ed immediately.
8 Assembling Attaching to the IR Series The DM-D500 can be attached directly to the IR Series using the “ DM-D pole unit for IR ” (DP-504). Required items The following items are used to attach the DM-D500 to the IR Series. These items are packed with the “ DM-D pole unit for IR ” (DP-50 4).
9 Engli s h 2. Attach the base to the setting position on the IR Series, and secure it with the screws. Note: When attaching the base, note that the corners of the base are set as shown below. 3. Pass the cable for the DM-D500 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click.
10 5. Conn ect the cable for the DM-D500 to the DM connector on the IR Series. Attaching to the TM-H5000II/TM-J8000 The DM-D500 c a n be attached dir ectly to the TM -H5000II/TM-J 8000 printers using the “ DM-D pole unit for TM printers (Type B) ” (DP-503).
11 Engli s h Assembling steps 1. Pass the cable for the DM-D500 through support C, and attach support C to the DM-D500. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the base to the setting position on the TM printer and secure it with the screws.
12 3. Pass the cable for the DM-D500 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D500 to the DM connector on the TM printer.
13 Engli s h Attaching to the TM-U375/TM-U950 The DM-D500 can be attached directly to the TM-U375/TM-U950 printers using the “ DM-D pole unit for TM printers (Type A) ” (DP-50 2). Required items The following items are used to attach the DM-D500 to the TM-U375/ TM-U950 printers.
14 Assembling steps 1. Pass the cable for the DM-D500 through support C, and attach support C to the DM-D500. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the rubber feet to the printer.
15 Engli s h 3. Pass the cable for the DM-D500 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D500 to the DM connector on the TM printer. 5. Adjust t he length of the cable and secure fixing plate A to the printer with screws.
16 6. Store any excess cable in the support, and attach the DM-D500 to fixing plate A. Attaching to the TM-H6000/TM-U675 The DM-D500 can be atta ched directly to the TM-H600 0/TM-U675 printers using the “ DM-D pole unit for TM printers (Type A) ” (DP-502).
17 Engli s h Assembling steps 1. Pass the cable for the DM-D500 through support C, and attach support C to the DM-D500. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the rubber feet to the printer.
18 4. Pass the cable for the DM-D500 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 5. Connect the cable for the DM-D500 to the DM connector on the TM printer. 6. Attach fixing plate A to the TM printer using the st opper.
19 Engli s h 7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fi xing screw.
20 Note: The paper roll cover may not open if the positi on of the display is inappropriate. Before securing the position of the display, make sure that you can open the paper roll cover. 8. Store any excess cable in the support an d attach the DM-D500 to fixing plate A.
21 Engli s h Attaching to Other TM Printers When using with other TM printers, the DM-D500 can be attached to a desk or other surface, using the “ DM-D pole unit for TM printers (Type A) ” (DP-502), and Velcro tapes or screws. Required items The following items are used when the DM-D500 is used wi th other TM printers.
22 2. Pass the cable for the DM-D500 through support C, and attach support C to the DM-D500. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 3. Pass the cable for the DM-D500 through the hole on fixing plate A, and fix the cable a t the bottom as shown be low.
23 Engli s h 5. Store any excess cable in the support, and attach the DM-D500 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. Assembling steps using screws 1. Follo w steps 2 and 3 in “ Assembling steps using Velcro tapes.
24 Attaching to the DM-D stand The DM-D500 can be attached directly to the DM-D stand using the “ DM-D stand unit for DM-D 500 ” (DP- 501). The DM-D500 with the DM-D stand can be co nnected to a TM printer, or be used as a stand alone produc t. Required items The following items are used to attach the DM-D500 to the DM-D stand.
25 Engli s h Connectors for the DM-D stand The connectors for the DM-D stand are as follows: Note: The DM-D stand comes with inch-type hexagonal lock screws installed to secure the interface cable to the interface connector for RS-232.
26 Jumper setting Set the jumpers on the DM-D sta nd as follows: The jumpers are located as follows: Precautions on using the power supply unit To avoid damage to the DM-D500 and the power supply unit, m ake sure to note the following points.
27 Engli s h Assembling steps 1. Pass the cable for the DM-D500 through the DM-D stand. When extending the length of the DM-D stand, attach the extension support (DP-105) to the DM-D stan d. 2. Insert t he tab on the DM-D500 (or the extension support) into the hole on the DM-D stand until you feel it click.
28 4. Conn ect one end of the computer interface cable to the computer connector on the DM-D stand; then connect the other end to the RS-232 connector on the computer. Tighten the screws on both ends of the cables to fasten them. 5. When using as a stand alone, go to step 6.
29 Engli s h 6. When not using the ex tension cable for power supply packed with the DM-D stand, go to step 7. When using the extension cable, connect i t (with the arrow mark up) to the extension cable connector indicated with “ POWER OUT ” on the DM-D stand; then connect the other end to the pow er connector on the printer.
30 9. Arrange the cable s as shown below. Put the cables for the DM-D500 inside the DM-D stand. 10. Attach the base plate to the DM-D stand following the number of the arrow shown below. At this time, push the base plate until it is locked by the hook on the DM-D stand.
31 Engli s h Part Names and Functions Exterior ❏ Display: Characters are displayed. ❏ Power switch: The power is turned on/off. ❏ DIP switch: The functions of the DM-D500 are changed. (See “ DIP switch ” for detail s.) Note: When turning on the DM-D500 again after turning it off, wait for at least 3 seconds.
32 DIP Switch DIP Switch Functions The DM-D500 has two gr oups of DIP switches . The functions of the DIP switches are as follows: DIP switch 1 (*1)XON/XOFF is eff ective only when the DM-D500 is connected with a stand alone. Transmission speed *Cannot be set to 57,600 or 115,200 when using the IR Series.
33 Engli s h DIP switch 2 (*1)The “ Y-connectio n enable ” is set when a TM printer with no modular jack for the DM-D is connected with this product, using one COM port to connect both TM printer and DM display. In this case, an optional DM-D stand (DP- 501) and a connecting cable are required.
34 Setting the DIP switches CAUTION: Turn off the DM-D500 while removing the DIP switch cover to prevent electrical damage to the DM-D500. 1. Turn off the power for the DM-D500. 2. Remove the DIP switc h cover. 3. Change each setting of the switches with a pointed object, such as a pen tip or small screwdriver.
35 Engli s h Turning and Tilting the DM-D5 0 0 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops.
36 Self Test The DM-D500 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch. Check Items of Self test The following items are checked during th.
37 Engli s h Specification General Specifications ❏ Height, Width, De pth and Weight • DM-D500: Height: 83 mm Width: 213 mm Depth: 51 mm Weight: 460 g • DM-D stand (DP-501): Height: 65 mm Width:.
38 • Base and support A of the “ DM-D pole unit for IR Series ” (DP-504): Height: 129 mm Width: 50 mm Depth: 53 mm Weight: 60 g • Base and support C of the “ DM-D pole unit for TM printers (.
39 Engli s h ❏ Tilt angle Max 48 ° (4 steps, 5 positions) ❏ Horizontal rotati on Max 90 ° (for ea ch left and right at 45 ° ) ❏ Vacuum fluorescent displ ay • Total number of dots: 256 (W) × 64 (H) dots • Dot pitch: 0.55 × 0. 55 mm • Number of characters: 32 column × 4 lines max.
40 Character Specifications ❏ Type of character • Alphanumeric chara cters: 95 • International characters: 37 • Extended graphics: 128 characters × 12 p ages • Kanji characters (The Kanji character model supports printing with one of the following character sets.
An important point after buying a device Seiko 201 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Seiko 201 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Seiko 201 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Seiko 201 you will learn all the available features of the product, as well as information on its operation. The information that you get Seiko 201 will certainly help you make a decision on the purchase.
If you already are a holder of Seiko 201, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Seiko 201.
However, one of the most important roles played by the user manual is to help in solving problems with Seiko 201. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Seiko 201 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
