Instruction/ maintenance manual of the product KE-265 Security 100
Go to page of 14
KE-265 Keyless Entry Access Control System Installation and Operations Manual.
Table of Contents ESSEX ELECTRONICS, INC. INTRODUCTION ....................................................................................... 2 KE-265 Series O VERVIEW ..................................................................................
Introduction Input Requirements The KE-265 accepts 12 to 24 volts AC/DC. An optional battery charging module and rechargeable Gel Cells are available to keep the system operational for up to 24 hours during a power interruption.
Prep aring for Inst allation Keypad Options All Essex Keypads are designed to perform reliably in even the most extreme environmental conditions. Operating temperatures can range from -40 ° C to +70 ° C (-40 ° F to 160 ° F).
The Inst allation Procedure 6. Do NOT mount Keypad at this time. 7. Proceed to Install the Wiring Cable. Required Tools Mounting Instructions 12 Pad 3x4: KP-34S, KP-34B or KP-34K You will need the following tools: The 3x4 keypad is designed to mount to a single gang switchbox or on a wall, pedestal or any flat surface of at least 3 ½ by 5 ¼”.
Install the Wiring Cable 1. Drill a ½” hole in the inside wall or ceiling where you want the cable to come through. 2. Pull the cable through the hole so the connector end goes to the keypad.
System Hardware Setup The Factory Default Settings are shown here: Remote By-Pass 1. All User Unlock Authorization is configured for Relay #1. (Master Code and Users 1,2 and Users 3,4,5). Factory Default Settings In some cases, it may be necessary to control the door from a remote area such as a security station or reception desk.
12 Latching Authorization Placing jumpers across the 4 th and 5 th set of pins (1,2 LATCH or 3,4,5 LATCH) determines which relay (if any) each User Group is authorized to manually latch.
14 System Programming Overview of System Code Programming There are TWO levels of codes for the KE-265 system. 1. The Master Code (used to open the door and for programming User Codes) 2. User Codes (used by personnel to open the door) IMPORTANT: Notes to remember before programming: 1.
16 Programming User Codes To Program a New User Code or Change an Existing User Code: 1. Choose a new 3 to 8 digit code that will be used for this User Code. ___ ___ ___ ___ ___ ___ ___ ___ 2. Decide which User Location to place this User Code (see Overview of User Codes) 3.
18 T roubleshooting These are a few troubleshooting suggestions to help assist with any problems you may experience. If the problem continues or is not answered here, please call Essex technical support at (800) KEYLESS Î (800) 539-5377. You can also visit Essex anytime at keyless.
20 Keypad beeps all by itself Constant Beeping - If the beep is consistently every 5 seconds, put a . 1 uf 16v (or higher) ceramic capacitor across wires 3 & 10 (black, violet) on terminal strip “A”. Random Beeping - Check for bad circuit ground going to the keypad.
22 23 Appendix A – Circuit Board Layout Upon receipt of such notification, Esse x Electronics, Incorporated w ill determine whether to repair or replace. We also re serve the right to hav e our representative make any inspection or repairs, or furnish replacements.
Appendix B- T ypical Wiring Diagrams Notes Note: Some low current strikes or relays w ill cause relay chatter due to inductive kickback. Attach MOV across st rike or relay to eliminate chatter.
An important point after buying a device Security 100 KE-265 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Security 100 KE-265 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Security 100 KE-265 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Security 100 KE-265 you will learn all the available features of the product, as well as information on its operation. The information that you get Security 100 KE-265 will certainly help you make a decision on the purchase.
If you already are a holder of Security 100 KE-265, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Security 100 KE-265.
However, one of the most important roles played by the user manual is to help in solving problems with Security 100 KE-265. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Security 100 KE-265 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
