Instruction/ maintenance manual of the product 625.34929 Sears
Go to page of 20
OWNERS MANUAL MODEL NO. 625.349290 CAUTION Read All Safety Guides Before You Start to Install Your Dispensing System SAVE THIS MANUAL -- HOW TO INSTALL- - HOW IT WORKS- - CARE OF- -- SPECIFICATIONS -- -- REPAIR PARTS-- Sears, Roebuck and Coo, Chicago, IL 60684 U.
TABLE OF CONTENTS PAGE NO, PAGE NO. Safety Guides ........................................ 3 What Does The Dispensing System Do ....... 3-4 Tools and Materials Needed ......................... 5 Put The System Together ........................ 6 Locating and Solution Injecting .
I SAFETY GUnDES A Read all steps, guides and rules carefully before installing and using your new Solution Dispensing System. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your dispensing system.
WHAT YOUR SOLUT OI water softener, installed on the outlet side of the pressure tank, filters and softens the water If you do not like a remaining chlorine taste, Sears has taste and odor filters to r.
TREATING WELL WATER PRE-TREATING PRIVATE WELL SYSTEMS HAVING IRON BACTERIA -- Before you put the dispensing system together and install it, chlor- inate the well if it contains more than 10 parts per million (ppm) of bacterial iron. Use the following steps.
PUT YOUR DISPENSING 1, Fasten the solution pump to the base with 4 nylon screws and nuts, as shown 2. Working through the tank fill hole, assemble the Low Level Indicator to the tank as shown, Positon the upper window port so the red indicator is easily seen_ 3.
WHERE TO LOCATE YOUR Locate the system where... ......a 115 volt, 60 Hz electrical power source is nearby. (See page 11) ...good fresh air flow will cool the solution pump motor and carry away solution fumes. ..... the area is clean and the air is free of dust.
I BLENDING TANK BLENDING TANK 42 ga! minimum -- separate inlet & outlet -- no air bag or diaphragm Pressure Tank Well I i I ' ,ill i BLENDING TANK 42 gal minimum -- separate inlet & outle.
GUBDES TO BNSTALL YOUR S (_) SOLUTION INJECTION INTO THE ALTERNATE DISCHARGE FITTING ON THE WELL PUMP 1. Turn off the electrical power to the well pump and turn off the gas or electric supply to the water heater 2. Open a faucet for a few seconds, to bleed off water pressure, then close 3.
I GUIDES TO _) SOLUTION INJECTION BETWEEN THE WELL PUMP AND PRESSURE TANK 1. Turn off the electrical power to the well pump and turn off the gas or electric supply to the water heater, 2. Open a faucet for a few seconds to bleed off water pressure, then close 11.
ELECTRICAL WgRRNG GUIDE, € A CAUTION: DO NOT TRY TO DO ANY WIRING IF YOU DO NOT KNOW ELEC- TRICITY. CALL A GOOD ELECTRICIAN A CAUTION: DO NOT DO ANY WIRING ON LIVE CIRCUITS ALWAYS TURN OFF THE ELECTRICAL POWER AT THE SOURCE, NOTE: All wiring must follow local or national electrical codes.
I RLL THE TANK WnTH THE SOLUTION DISPENSING SYSTEM RESER- VOIR (TANK) HOLDS 15 GALLONS OF SOLUTION. HOWEVER, ON THE FIRST FILL, ALLOW SOME ROOM IN THE TANK SO THE SOLUTION STRENGTH CAN BE CHANGED IF NEEDED. DE- PENDING ON THE WATER PROBLEM YOU ARE TREATING, FILL THE TANK AND SET THE FEED RATE AS FOLLOWS.
I RLL THE TANK WroTH SOLUT 1. Residual still above 0.6, and the feed control knob at 1 or 2-- Use less chlorine in the mixture For example, use 1 gallon of bleach for each 2 gallons of water instead of 1 to 1 2.
FILL THE TANK WnTH 3. Turn the relief-release valve (clockwise only FIG. 11, page 12) to the open position_ Solution is pumped through the suction tubing, into the pump head, then returned to the tank (takes 3-5 minutes).
KEEP YOUR DaSPENSUNG RESERVOIR (TANK) SOLUTION LEVEL -- After installing the solution dispensing system, check the solution level in the tank daily. Red shows in the Low Level Indicator when about 5 gallons of solution remains. After awhile, you will know about how much solution it uses each day and how often to refill the tank.
I KEEPYOUR DUSPENSnNG LUBRICATION -- At least every 6 months, lubricate the solution pump as follows: 1. Unplug the electrical power cord, 2. Loosen the set screw in the feed control knob and remove the knob and bushing, 3. Remove the pump top cover, 4.
KEEP YOUR D SPENSING If the dispensing system is exposed to the sun, replace the solution tubing every6 months. Re- place the tubing yearly if the system is installed indoors.
27 26 25---'- MODEL NO. 625.349290 9 ! 16 RETURN I / m -N m.
PARTS LiST MODEL NO. 625.349290 NO. 1 2 4 5 6 7 8 9 10 11 KEY PART NUMBER 818405 818399 818510 8800650 U0812612 818382 811704 811703 8800418 814211 8800702 12 812318 13 816342 14 L98013_-188 15 810036 16 U0816093 8800710 17 818544 18 8800470 DESCRIPTION Float Assembly Pipe, Low Level Indicator Tank Cap Tank, 15 Gal.
S AI S OWNERS MANUAL SERVICE MODEL NO. 625.349290 HOW TO ORDER REPAIR PARTS TELL SEARS YOU WANT IT INSTALLED THEN RELAX (F642-5289) Now that you have purchased your Solution Dispensing System, should .
An important point after buying a device Sears 625.34929 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 625.34929 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 625.34929 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 625.34929 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 625.34929 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 625.34929, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 625.34929.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 625.34929. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 625.34929 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
