Instruction/ maintenance manual of the product 149.213340 Sears
Go to page of 16
SERIAL OR CODE NUMBER: Model and code number may be found on1he right side of Spindie Housing You should record both model and serial number and retain in a satepiace for future use CALIFORNIA OWNERS: a unique serial code number is stamped inside the Pulley Cover CAUTION: Read All Instructions Carefully Before Start- ing Assembly and Use.
FULL ONE-YEAR WARRANTY ON CRAFTSMAN RADIAL DRILL PRESS If within one year from date of purchase, this Craftsman RADIAL DRILL PRESS fails due to a defect in materi- al or workmanship, Sears will repair it, free of charge WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER IN THE UNITED STATES, .
4 REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see thatkeys and adjusting wrenches are removed from tool before turning on 5 KEEP WORK AREA CLEAN Cluttered areas and beeches invite acc.
SAFETY RULES FOR DRILL PRESSES 1 DO NOT USE until unit is completely assembled and installed according to instructions 2 USE ONLY CHUCK KEY PROVIDED WiTH YOUR RADIAL DRILL PRESS It is equipped with a .
TOOLS REQUmRED 8-inch Adjustable Mallet Wrench UNPACKRNG AND CHECKUNG CONTENTS Model 149213340 Radial Drill Press is shipped complete in one carton Carefully unpack and separate parts from packing mat.
ASSEMBLY WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT THE RADIAL DRILL PRESS TO A POWER SOURCE UNTIL ALL ASSEMBLY STEPS ARE COMPLETE_ AND YOU HAVE READ AND UNDERSTOOD SAFETY AND OPERATIONAL INSTRUCTION.
I 7 Make sure bottom of Spindle Shaft (REF 42) and bore of Chuck (REF 46) are clean and free of grease Press Chuck up onto Spindle Shaft_ NOTE: To avoid damage to Chuck, rotate Chuck barrel until jaws are fully open.
CONTROLS AND ADJUSTMENTS _ WARNING: MAKE SURE SWITCH IS IN OFF POSmON AND POWER CORD IS UNPLUGGED BEFORE PERFORMING CHECKS= ADJUSTMENTS I OR SETUP PROCEDURES, On-Off Switch 2.
I Cast Tab Spring Assembly /_ ))_ Feed Shaf< _ ) Lock'Nuts 3 Check operation of Return Spring for proper tension and full return 4 Nuts must be tightened before use Be very careful; the nuts h.
Belt Tension Butterfly Set Screw Angle Gauge (REF 85) on Column head and full length scored V groove on Horizontal Tube (REF 81) to set desired angle Lock in position using Lock Handle When returning .
Adjusting Spindle Perpendicular to Table The Radial Drill Press was factory-adjusted and set with Spindle Housing perpendicular to table No further adjust- ment should be necessary However.
OPERATaON Correct Drilling Speeds See "Changing Speeds" section under "Controls and Adjustments" and Speed Chart inside Pulley Cover for cor- rect drilling speeds Always disconnect.
ACCESSORUES Mortising Kit Vises and Clamps Although not designed specifically for mortising, the variety of possible drill angles and feed lengths with the Radial Drill Press make possible some former.
CRAFTSMAN 344NCH RADIAL DRILL PRESS MODEL No. 149.213340 REPAnR PARTS 72 71 7 14 ---i 87 14/__ 6 12 17 5 J 4 I I 88 15 3 53 30 29 89 : 34 54 14.
CRAFTSMAN 34-iNCH RADIAL DRULL PRESS MODEL No. 149.213340 PARTS LIST REF NO, 1 2 3 4 8 6 7 8 9 10 11 12 !3 14 15 18 17 18 !9 2O 21 22 23 24 25 281 27 28 29 30 31 32 33 34 35 36 37 3R 39 4O 41 42 43 44 45 46 46A 47 48 49 5O PART NO.
TROUBLESHOOTING CHART TROUBLE PROBABLE CAUSE REMEDY Noisy operation 1 Incorrect V-belt tension 1_ Adjust tension 2 Dry spindle shaft 2. Lubricate spindle shaft See "Maintenance" section 3 Loose Spindle shaft or 3 Tighten Lock Nut (left hand thread) or pulley Motor Pulley set screw, Bit burns or smokes 1 Incorrect spindle speed.
An important point after buying a device Sears 149.213340 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 149.213340 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 149.213340 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 149.213340 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 149.213340 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 149.213340, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 149.213340.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 149.213340. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 149.213340 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
