Instruction/ maintenance manual of the product MobileMax ST500LT032 Seagate
Go to page of 32
Product Manual Seagate ® Laptop Ultrathin HDD SATA Gen 9.3 100715053 Rev. A May 2013 Standard models ST500LT032 ST320LT030 Self-Encrypting Drive models ST500LT033 ST320LT031.
© 2013 Seagate Technology LLC. All rights reserved. Publication number: 100715053, Rev. A May 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A III C ONTENTS S EAGATE T ECHNOLOGY S UPPORT S ERVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.0 I NTRODUCTION . . . . . . . . . . . . . .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A IV F IGURES F IGURE 1T YPICAL 5V S TARTUP AND O PERATION C URRENT P ROFILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 F IGURE 2A TTACHING SATA C ABLING . . . . . . . . . .
Seagate Laptop Ultrathin HDD SATA Product Manual, Rev. A 1 For information regarding online support and services, visit http://www.seagate.com/about/contact-us/technical-support/ Available services in.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 2 1.0 I NTRODUCTION This manual describes the functional, mechanical and interface specifications for the following Seagate ® Laptop Ultrathin HDD SATA model drives: These drives provide the following key features: 5400-RPM spindle speed.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 3 1.1 A BOUT THE S ERIAL ATA I NTERFACE The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages incl ude: Easy installation and configuration with true plug-and-play connectivity.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 4 D RIVE S PECIFICATIONS 2.0 D RIVE S PECIFICATIONS Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 5 D RIVE S PECIFICATIONS 2.1 F ORMATTED C APACITY F ORMATTED C APACITY (1) 1. One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 6 D RIVE S PECIFICATIONS 2.3 R ECORDING AND I NTERFACE T ECHNOLOGY Recording method Perpendicular Recording density 1885 Kb/in Track density 366 ktracks/in avg Areal density 690 Gb/in 2 avg Spindle speed 5400 RPM +/- 0.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 7 D RIVE S PECIFICATIONS 2.7 P OWER S PECIFICATIONS The drive receives DC power (+5V) through a native SATA power connector (refer to Figure 2 ). 2.7.1 Power consumption Power requirements for the drives are listed in the table in Table 3 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 8 D RIVE S PECIFICATIONS 2.7.1.1 Typical current profiles The typical 5V startup and operation current profile is shown in Figure 1 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 9 D RIVE S PECIFICATIONS 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 10 D RIVE S PECIFICATIONS 2.8 E NVIRONMENTAL S PECIFICATIONS This section provides the temperature, humidity, shock, and vibration specifications for Momentus drives. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 11 D RIVE S PECIFICATIONS 2.9 A COUSTICS Drive emission of sound is measured consistent with the ECMA-74 and its referenced standards. Testing is conducted at room temperature (approximately 25°C).
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 12 D RIVE S PECIFICATIONS 2.11 R ELIABILITY Nonrecoverable read errors 1 per 10 14 bits read, max Load/Unload (U/UL) 25°C, 50% relativ.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 13 D RIVE S PECIFICATIONS Reorient the receiving antenna. Move the device to one side or the other of the radio or TV.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 14 C ONFIGURING AND M OUNTING THE D RIVE 3.0 C ONFIGURING AND M OUNTING THE D RIVE This section contains the specifications and instructions for configuring and mounting the drive.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 15 3.3 D RIVE M OUNTING You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting h oles. Refer to Figure 3 for drive mounting dimensions.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 16 S ERIAL ATA (SATA) I NTERFACE 4.0 S ERIAL ATA (SATA) I NTERFACE These drives use the industry-standard Seri al ATA interface that supports FIS data tran sfers. It supports ATA programmed input/ output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 17 N OTES 1 All pins are in a single row, with a 1.27 mm (0.050 in) pitch. 2 The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 18 S ERIAL ATA (SATA) I NTERFACE Set Features EFh Set Max Address F9h Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 19 S ERIAL ATA (SATA) I NTERFACE 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Ta ble 7 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 20 S ERIAL ATA (SATA) I NTERFACE 51 PIO data-transfer cycle timing mode 0200 H 52 Retired 0200 H 53 Words 54–58, 64–70 and 88 are v.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 21 S ERIAL ATA (SATA) I NTERFACE 93 Hardware reset value (see description following this table) xxxx H 94 Auto acoustic management setting xxxx H 95 Stream Min.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 22 S ERIAL ATA (SATA) I NTERFACE Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 23 S ERIAL ATA (SATA) I NTERFACE 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 24 S ERIAL ATA (SATA) I NTERFACE 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 25 I NDEX A acoustics 11 active mode 9 Address 18 agency certification 12 ambient temperature 6 areal density 6 ATA commands 17 Austral.
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 26 I NDEX N noise 9 nominal power 6 nonoperating shock 10 nonoperating vibration 10 nonrecoverable read errors 12 O operating shock 10 .
S EAGATE L APTOP U LTRATHIN HDD SATA P RODUCT M ANUAL , R EV . A 27 I NDEX U UL60950-1 12 V vibration 10 voltage dips, interrupts 11 voltage tolerance 9 W warranty 12 weight 6 width 6 Write Buffer 18 .
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte.
An important point after buying a device Seagate MobileMax ST500LT032 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Seagate MobileMax ST500LT032 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Seagate MobileMax ST500LT032 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Seagate MobileMax ST500LT032 you will learn all the available features of the product, as well as information on its operation. The information that you get Seagate MobileMax ST500LT032 will certainly help you make a decision on the purchase.
If you already are a holder of Seagate MobileMax ST500LT032, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Seagate MobileMax ST500LT032.
However, one of the most important roles played by the user manual is to help in solving problems with Seagate MobileMax ST500LT032. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Seagate MobileMax ST500LT032 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
