Instruction/ maintenance manual of the product KSD-541 Seagate
Go to page of 18
-1- Industrial 5-Port Fa st Ethernet Switche s with SFP Slot a nd option al 4 PoE PSE Ports Ba sic Model: KSD-541 PoE Model: KSD-541-P In stallation Guide DOC.
-2- (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc.
-3- The information contained in this document is subject to change without prior notice. Copyright (C) . All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. W ARNING: This equi pment ha s been tested a nd found to comply with the li mits for a Cla ss A digital device, pursua nt to Part 15 of the FCC Rules.
-4- T a ble of Contents 1. Introduction .................................................................................................. 5 1.1 Features .................................................................................................
-5- 1. Introduction The switches are 5-port Fa st Ethernet switches which are f eatured with four copper ports a nd one combo port. The combo port comes with one RJ-45 a nd one SFP slot. The SFP slot ca n be mounted with a fiber tra nsceiver optionally to support a fiber connection.
-6- 1.1 Fe ature s Provides 5 10/100Mbps RJ-45 a nd one 100Mbps SFP slot All copper ports support auto-negoti ation a nd auto-MDI/MDI-X detection Provides full wire speed forwarding Supports IEEE 802.
-7- 1.4 Specif ication s Copper Ports w/h PSE (P2-P5) Compli a nce IEEE 802.3 10Ba se-T , IEEE 802.3u 100Base-TX Connectors Shielded RJ-45 ja cks Pin a ssignments Auto MDI/MDI-X detection Configuration Auto-negoti ation T ra nsmission rate 10Mbps, 100Mbps Duplex support Full/Half duplex Network ca ble Cat.
-8- Power over Ethernet Function (PoE Model) PSE Pin 4,5 Positive of power voltage (T ypical 48V DC) PSE Pin 7,8 Negative of power voltage (T ypical 48V DC) Discovery PD resista nce 15K ~ 33K PD Cla ssification Cla ss 0 ~ 4 Power delivery 15.
-9- 2. In stallation 2.1 Un pa cking The product pa ckage contains: • The switch unit • One product CD-ROM 2.2 Safety Cautions T o reduce the risk of bodily injury , electrical shock, fire, a nd da mage to the product, observe the following precautions.
-10- 2.4 Din-Rail Mounting The steps to mount the switch on a Din-rail are: One Din-rail mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit.
-11- 2.5 Pa nel Mounting One pa nel mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit.
-12- Using T erminal Blocks Three terminal conta cts are provided: V dc Positive ( + ) termin al V dc Negative ( - ) termin al Cha ssis ground * Working V dc for general a pplication: +6V ~ +60V DC * Working V dc for PoE a pplication : +43V ~ +54V DC (T yp.
-13- 3. M a king Connection s 3.1 Ma king UTP Conne ction s The copper ports support the following connection type s a nd dista nce s: Network Cables 10BASE-T : 2-pair UTP Cat.
-14- 3.3 Ma king PoE Connection s This section describes how to make a connection between a PSE port a nd a PoE PD device. For the PoE switch model, Port 2, Port 3, Port 4 a nd Port 5 are equi pped with PoE PSE function. The ports are ena bled to deliver power together with network signal to a connected powered device vi a Cat.
-15- 3.4 LED Indication L ED Function State Interpretation POWER Power status O N The power is supplied to the switch. OFF The power is not supplied to the switch. LIN K/ACT Por t l ink status O N A port link is e sta blished. (No traf fic) BLIN K Port link is up a nd there is traffic.
-16- 4. Application s 4.1 Application s with Ba sic Switch Model The following figure illustrates a ba sic switch model connects five computers vi a Cat.5 ca ble s. The following figure illustrates a ba sic switch model connects four computers vi a Cat.
-17- 4.2 Applications with PoE Switch Model The figure below illustrates a PoE switch connects f our PoE IP camera s via Cat.5 ca ble s a nd uplinks to a fiber ba ckbone: The figure below illustrates a PoE switch connects f our PoE WLAN a ccess points vi a Cat.
-18- The figure below illustrates a PoE switch powered by a 48V DC power a da pter connects four PoE medi a converters vi a Cat.5 ca bles a nd uplinks to a fiber ba ckbone:.
An important point after buying a device Seagate KSD-541 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Seagate KSD-541 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Seagate KSD-541 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Seagate KSD-541 you will learn all the available features of the product, as well as information on its operation. The information that you get Seagate KSD-541 will certainly help you make a decision on the purchase.
If you already are a holder of Seagate KSD-541, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Seagate KSD-541.
However, one of the most important roles played by the user manual is to help in solving problems with Seagate KSD-541. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Seagate KSD-541 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center