Instruction/ maintenance manual of the product GC-STT-V Scag Power Equipment
Go to page of 23
MODEL GC-STT-V THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSOR Y . READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSOR Y PERFORMING T O MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJUR Y . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning.
1 1.1 INTRODUCTION This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference.
2 3.1 ASSEMBLY INSTRUCTIONS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access. Prepare the work area making sure that it is a clean, safe environment.
3 DISCHARGE CHUTE OPENING FRONT OF CUTTER DECK REAR OF CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-52"GC-STT install art CUTTER DECK BELL CRANK LIFT LINK SPACER SPACER NUT NUT WASHER BOLT, 3/8-16 x 1-1/2" BOLT, 3/8-16 x 1-1/4" 52" Cutter Deck FIGURE 3-3 8.
4 FIGURE 3-5 RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) 2006 GC-STC-V install art 3 BLOWER ASSEMBLY MOUNTING BRACKET MOUNTING PIN TIGHTEN MOUNTING BRACKET HARDW.
5 13 . Install the hopper mounting brackets (p/n 451512) to the outside of the frame on the rear of the machine using 3/8-16 x 1" hex head bolts (p/n 04001-19) and 3/8-16 elastic stop nuts (p/n 04021-09).
6 FIGURE 3-8 1 1 2 3 3 3 3 3 4 4 4 4 5 5 4 4 Item # P ar t # Description 1 04001-46 Bolt, He x Head 3/8-16 x 2-1/4" 2 04001-19 Bolt, He x Head 3/8-16 x 1" 3 04021-09 Nut, Elastic Stop 3/8-16 4 04030-04 Lockw asher , 3/8 Spr ing 5 04041-07 Flatwasher , 3/8-.
7 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the bag assemblies from the grass catcher. 3. Remove the rubber strap holding the adapter to the blower assembly. See Figure 4-1. 4. Remove the belt from the spindle pulley and the large hair pin securing the blower to the discharge chute mounting hole.
8 5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS * Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.
9 NOTES.
10 GC-STT -V BLO WER HOUSING ASSEMBL Y 2005 GC V+ Blower Assembly 45 47 45 4 7 8 9 9 10 10 11 11 12 12 13 14 14 14 14 15 15 16 17 18 19 20 21 22 23 24 24 27 27 28 30 31 31 32 33 34 35 35 37 38 39 40 4.
11 1 04067-07 Pin, Ring 2-1/4" Long 2 481547 Lanyard, Deck Height Pin 3 04019-02 Nut, Serr . Flange 1/4-20 4 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 5 481377 Decal, Blower 6 482080 Decal, Ro.
12 GC-STT -V BLO WER MOUNTING COMPONENTS UNDER SIDE OF VELOCITY-PLUS CUTTER DECK SHOWN 23 23 28 24 24 25 25 26 26 16 16 25 27 1 2 3 4 5 6 6 7 8 9 10 10 11 12 13 14 15 15 16 17 18 19 20 2006 GC-STC-V B.
13 GC-STT -V BLO WER MOUNTING COMPONENTS Ref. Part No. Number Description 1 483225 Belt Cov er , GC-STT - 52" 483227 Belt Cov er , GC-STT - 61" 2 04029-04 Wi ngnut, Plastic 3/8" Small 3 483223 C ap , Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter , Blower GC-STT , includes item #7 6 04040-14 Flatwasher , 1/4-.
14 GC-STT -V B UCKET SUPPORT COMPONENTS 1 2 3 4 4 6 8 5 5 9 9 9 9 5 11 5 16 16 16 16 16 16 18 18 13 13 19 20 14 21 21 22 23 23 24 31 11 5 32 33 33 26 27 28 29 30 32 3 41 42 40 49 9 48 47 46 13 45 4 25.
15 GC-STT -V B UCKET SUPPORT COMPONENTS R e f . Part No . Number Description 1 423302 Screen, Catcher Hood 2 04090-02 P op Riv et, 3/16 x .652 3 04041-19 Flatwasher , 3/16-.196 x .469 x .048 4 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4" 5 04041-07 Flatwasher , 3/8-.
16 1 2 3 4 5 6 7 8 9 10 11 12 13 390STT0201 GC-STT -V B A G SUPPOR T BRA CKET AND SEAL.
17 GC-STT -V B A G SUPPOR T BRA CKET AND SEAL Ref. Part No. Number Description -NOTE- Some of the hardware is common hardware and you may purchase it locally.
18 GC-STT DECALS 481039 482275 481327 483037 481377 482080 483044.
19 NOTES.
LIMITED W ARRANTY- COMMERCIAL A CCESSOR Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor.
P ART NO. 03181 PRINTED 7-2005 PRINTED IN USA © 2005 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC WWW .SCAG .COM.
An important point after buying a device Scag Power Equipment GC-STT-V (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Scag Power Equipment GC-STT-V yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Scag Power Equipment GC-STT-V - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Scag Power Equipment GC-STT-V you will learn all the available features of the product, as well as information on its operation. The information that you get Scag Power Equipment GC-STT-V will certainly help you make a decision on the purchase.
If you already are a holder of Scag Power Equipment GC-STT-V, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Scag Power Equipment GC-STT-V.
However, one of the most important roles played by the user manual is to help in solving problems with Scag Power Equipment GC-STT-V. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Scag Power Equipment GC-STT-V along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
