Instruction/ maintenance manual of the product PK1A20001 SATO
Go to page of 8
C C T T 4 4 0 0 0 0 / / C C T T 4 4 1 1 0 0 P P l l u u g g & & P P l l a a y y ) Q H – n a p a J ( r o C O T A S p n o i t a r o R R e e t t a a i i l l P P r r i i n n t t e e r r ) e r o .
CT4xx Series Quic k Guide Pg 13 Options Label Cutter This is an internal option allowing lab els to be cut at specified intervals. Controlled through pr ogramm ing.
CT4xx Series Qu ick Guide Pg 12 CT4xx Series Quick Guide Pg 1 Printer Specifications Table of Contents What You Get …………………………… ……………………………… ……... 2 Connecting The Printer ………………… …………………………………….
CT4xx Series Quick Guide Pg 2 CT4xx Series Quic k Guide Pg 11 6. If you are still unable to get printer output, try the Hex Dump as described in Step 5 under t he Parallel Interface trouble shooting. In this case, t he printer monitors its RS232C interface for incoming data.
CT4xx Series Quick Guide Pg 3 CT4xx Series Quic k Guide Pg 10 Connecting The Printer 6. When you send the prin t job to the printer and it does not resp ond, and there is no error message on t he PC : a. Check your data stream for some of the basics. Is your job framed as follows : 1.
CT4xx Series Quick Guide Pg 4 CT4xx Series Quick Guide Pg 9 Troubleshooting 9. Apply power to the printer by placing th e AC Power switch in the ON (1) position. Initial Checklist 10. Print a test label to verify the prin ter is set up and operating correctly.
CT4xx Series Quick Guide Pg 5 CT4xx Series Quick Guide Pg 8 Note: CT Series ribbons are wound face ( ink side) out. Make sure the dul l (ink) side of the ribbon will be in con tact with the paper and the supply co re is on the rear spindle.
Route Paper under the Sensor CT4xx Series Quick Guide Pg 6 1. Remove power from the printer by placing t he Power Switch in the OFF (0) position. 2. Open the Top Cov er by pressing on cover release points located on each side of the printer. 3. Release the Print Head Assembly by pressi ng the Head Latch to the rear.
An important point after buying a device SATO PK1A20001 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought SATO PK1A20001 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data SATO PK1A20001 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, SATO PK1A20001 you will learn all the available features of the product, as well as information on its operation. The information that you get SATO PK1A20001 will certainly help you make a decision on the purchase.
If you already are a holder of SATO PK1A20001, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime SATO PK1A20001.
However, one of the most important roles played by the user manual is to help in solving problems with SATO PK1A20001. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device SATO PK1A20001 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
