Instruction/ maintenance manual of the product LNS-S03 Sanyo
Go to page of 10
T ype of the Cabinet (1) See P age 2 LCD PR OJECT OR LENS MODEL NO . LNS-S03 LENS REPLA CEMENT AND INST ALLA TION PR OCEDURES NO TES ON REPLA CEMENT AND INST ALLA TION The procedures and the needed pars f or lens installation depend on the type of cabinet.
Some par ts are not used f or installation or replacement. K eep these par ts f or later use. Note : Figures in this manual ma y be diff er from the actual product. NO TES ON LENS INST ALLA TION • Lens installation and replacement should be made by the qualified service per- sonnel.
LENS REPLA CEMENT AND INST ALLA TION PROCEDURE {T ype (1) Cabinet} -2- 1 Remove Lower Lens Cover. Remove 2 Screws A. Push part B and pull Lower Lens Cover down. (See Fig. 1.) 2 Remove 4 Screws C. Pull Upper Lens Cover toward front and remove. (See Fig.
5 Connect Lens Motor Lead to the connector "K96T" on the circuit board under the lens. 4 Replace Lens Cap on the rear (mounting side) of Projection Lens and mount the lens on Lens Mouting Bracket with 4 Screws. To mount the lens with Lens Motor on the right.
Fig-6 LIGHT BLOCK SHEET Make sure the sheet figure and put on proper position. -4- 6 Use a Light-Block Sheet (provided with projector) corresponding with lens. (Refer to the Type No. below.) Set Light-Block Sheet through the lens. Make sure the shape of Light-Block Sheet and be sure to set them as shown in the Fig.
-5- 7 Replace Upper Lens Cover. Slide Light-Block Sheet into the guide of Upper Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 4 Screws C. (See Fig. 2.) 8 Replace Lower Lens Cover. Slide Light-Block Sheet into the guide of Lower Lens Cover and set them in front of the flap.
LENS REPLA CEMENT AND INST ALLA TION PROCEDURE {T ype (2) Cabinet} -6- 1 Remove Lens Cover. Remove 2 Screws A. Push part B and pull Upper Lens Cover up. (See Fig. 1.) 2 Remove 4 Screws C. Pull Lower Lens Cover toward front and remove. (See Fig. 2.) 3 Remove 2 Screws D and Cover Plate on the back of Upper Lens Cover.
-7- 5 Connect Lens Motor Lead to the connector "K96T" on the circuit board under the lens. Fix Lens Motor Lead with the lead holder on the cir- cuit board.
6 Use 2 Light-Block Sheets (provided with projector) corresponding with lens. (Refer to the Type No. below.) Set 2 Light-Block Sheets through the lens. Make sure the shape of Light-Block Sheets and be sure to set them as shown in the Fig. 6. Fig-6 LIGHT BLOCK SHEETS Make sure the sheets figure and put on proper position.
-9- 7 Replace Lower Lens Cover. Slide Light-Block Sheets into the guide of Lower Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 4 Screws C. (See Fig. 2.) 8 Replace Upper Lens Cover. Slide Light-Block Sheets into the guide of Upper Lens Cover and set them in front of the flap.
An important point after buying a device Sanyo LNS-S03 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo LNS-S03 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo LNS-S03 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo LNS-S03 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo LNS-S03 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo LNS-S03, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo LNS-S03.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo LNS-S03. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo LNS-S03 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
