Instruction/ maintenance manual of the product SRP-350 Samsung
Go to page of 30
Operator’s Manual All specifications are subjected to change without notice http://www.samsungminiprinters.com SRP-350 Ver.2 RECEIPT PRINTER 1 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage.
2 Violating following instructions can cause slight wound or damage the appliance. Keep the desiccant out of children’s reach. If not, they may eat it. Install the printer on the stable surface. If the printer falls down, it can be broken and you can hurt yourself.
4 Table of Contents CHAPTER 1. SETTING UP THE PRINTER ..................................... 5 1-1. U NPACKING .............................................................................. 5 1-2. C ONNECTING THE C ABLES ...............................
6 1-2. Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector pa nel on the back of the printer, which is shown below : Notes : Before connecting any of the cables, make sure that both the printer and the host are turned off.
8 1-5. Connecting the Power Supply CAUTIONS: When connecting or di sconnecting th e power supply from the pri nter, make sure th at the power supply is not plugged into an elec trical outlet .
10 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of pa per, as shown. Then close the cover. 7. Tear off the paper as shown. Notes : When closing the cover, press the center of printer cover firmly to prevent p a p er miss-loadin g 11 1-7.
12 1-8. Using the Printer Control Panel Button The button can be disabl ed by the ESC c 5 command. Press the FEED button once to advance pap e r one line. You can also hold down the FEED button to feed paper continuously. Panel lights POWER The POWER light is on whenever the printer is on.
14 Parallel/USB Interface Specification Dip Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Auto Line Feed Always Enabled Always Disabled OFF 2 Reserved - - OFF 3 Reserved - - OFF 4 Reserved - - O.
16 Chapter 3. The self test The self-test checks whether the printer has any problem s. If the printer does not function properly, contact your dealer. Th e self-test checks the following; 1. Make sure paper roll has been i nstalled properly . 2. Turn on the power while holdin g down the FEED button.
18 Page 2 ( PC850 : Multilingual ) 19 Page 3 ( PC860 : Portuguese ).
20 Page 4 ( PC 863 : Canadian - French ) 21 Page 5 ( PC 865 : Nordic ).
22 Page 19 ( PC 858 : Euro ) 23 Page 255 ( Space Page ).
24 International Character Set 25 Chapter 5. Control Commands List C o n t r o l c o d e s Hexadecimal C o d e s Function <HT> 09 Horizontal tab <LF> 0A Print and line feed <FF> 0 C .
26 Control codes Hexadecimal c o d e s Function <ESC> c 3 n 1B 63 33 n Select paper sensor to output pap er end signals <ESC> c 4 n 1B 63 34 n Select paper sensor to stop p rinting <ESC.
28 CAN [Name] [Format] [Description] Cancel print data i n page mode. ASCII CAN H e x 1 8 Decimal 24 In page mode, deletes all the print data in the current printabl e area. DLE EOT n [Name] [Format] [Range] [Description] Real-time status transmission.
30 ESC FF [Name] [Format] [Description] Print data i n page mode. A S C I I E S C F F H e x 1 B 0 C D e c i m a l 2 7 1 2 In page mode, prints all buffered data in th e printing area coll ectively. ESC SP n [Name] [Format] [Range] [Description] Set right-side character spacing.
32 ESC * m nL nH d1…dk [Name] [Format] [Range] [Description] Select bit-i mage mode. A S C I I E S C * m n L n H d 1 … d k H e x 1 B 2 A m n L n H d 1 … d k D e c i m a l 2 7 4 2 m n L n H d 1 .
34 ESC D n1… nk NUL [Name] [Format] [Range] [Description] Set horizontal tab positions. A S C I I E S C D n 1 … n k N U L H e x 1 B 4 4 n 1 … n k 0 0 D e c i m a l 2 7 6 8 n 1 … n k 0 1 ≤ n ≤ 255 0 ≤ k ≤ 32 Sets horizontal tab positions.
36 ESC T n [Name] [Format] [Range] [Description] [Default] Select print di rection in page mode. A S C I I E S C T n H e x 1 B 5 4 n D e c i m a l 2 7 8 4 n 0 ≤ n ≤ 3 48 ≤ n ≤ 51 Selects the pri nt direction and s tarting posit ion in page mode.
38 ESC c 4 n [Name] [Format] [Range] [Description] Select paper sensor(s) to stop printing. A S C I I E S C c 4 n H e x 1 B 6 3 3 4 n D e c i m a l 2 7 9 9 5 2 n 0 ≤ nL ≤ 255 Selects the paper sen.
40 FS q n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n [Name] [Format] [Range] [Description] Defined NV bit i mage. A S C I I F S q n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n H e x 1 C 7 1 n.
42 GS B n [Name] [Format] [Range] [Description] Turn white/black reverse pri nting mode on/off. A S C I I G S B n H e x 1 D 4 2 n D e c i m a l 2 9 6 6 n 0 ≤ n ≤ 255 Turns on or off whit e/black reverse print ing mode. * When the LSB is 0, white/black re verse pri nting mode is turned o ff.
44 GS W nL nH [Name] [Format] [Range] [Description] Set printing area width. A S C I I G S W n L n H H e x 1 D 5 7 n L n H D e c i m a l 2 9 8 7 n L n H 0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255 Sets the printing area width to the area specified by nL and nH.
46 First byte (printer information) Bit Off/On Hex Decimal Status for ASB 0 Off 00 0 Not used. Fixed to Off. 1 Off 00 0 Not used. Fixed to Off. Off 00 0 Drawer kick-out connector pin 3 is LOW. 2 On 04 4 Drawer kick-out connector pin 3 is HIGH. Off 00 0 Onl ine.
48 ① GS k m d1…dk NUL , ② GS k m n d1…dn [Name] [Format] [Range] [Description] Print bar code. ① A S C I I G S k m d 1 … d k N U L H e x 1 D 6 B m d 1 … d k 0 0 Decimal 29 107 m d1…dk .
50 APPENDIX A. Star Mode Command Summary Control codes Hexadecimal codes Function <ESC> ”R” n 1B 52 n Select international character set <ESC> <GS> t n 1B 1D 74n Select character.
52 Control codes Hexadecimal codes Function <FS> 1C Co ntrol peripheral device #1 immediately. <EM> 19 Control peripheral device #2 immediately <SUB> 1A Co ntrol peripheral device #2 immediately <ESC> “d” n 1B 64 n Partial-cut com mand to the auto cutter.
54 RS-232C Cable Connection RS-485 Cable Connection 55 Interface Connector Serial Interface (RS-232) Pin No. Signal name Direction Function 1 FG - Frame Ground 2 TxD Output Transmit Data 3 RxD Input R.
56 Parallel Interface (IEEE-1284) Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk HostClk 2 Host / Printer Data 0 (LSB) - Data 0 (LSB) 3 Host / Printer Data 1 - Data 1 4.
58 D. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dots/mm) Printing width 72.192 ± 0.2mm Paper width 79 ~ 80 mm Characters per line (default) 42 (Font A) 56 (Font B) Printing speed 35.
An important point after buying a device Samsung SRP-350 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Samsung SRP-350 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Samsung SRP-350 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Samsung SRP-350 you will learn all the available features of the product, as well as information on its operation. The information that you get Samsung SRP-350 will certainly help you make a decision on the purchase.
If you already are a holder of Samsung SRP-350, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Samsung SRP-350.
However, one of the most important roles played by the user manual is to help in solving problems with Samsung SRP-350. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Samsung SRP-350 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
