Instruction/ maintenance manual of the product A502 Samsung
Go to page of 108
ENGLISH User ’ s Manual Thank you for buying a Samsung Camera. This manual will guide you through using the camera, including capturing images, downloading images and using the software applications. Please read this manual carefully before using your new camera.
《2》 Instructions Insert the USB cable Set up the camera driver Before connecting the camera to a PC, via the USB cable, you will need to set up the camera driver. Install the camera driver that is contained in the Application S/W CD-ROM.(p.89) Take a picture (p.
● Getting to know your camera 5 ● About the icons 5 ● Danger 6 ● Warning 6 ● Caution 7 ● An FCC warning 7 ● System chart 8 ● Identification of features 10 ■ Front & Top 10 ■ Ba.
● Using the camera buttons to adjust the camera 47 ● Thumbnail/ Enlargement button 47 ● Voice memo/ Up button 48 ● Play & Pause/ Down button 49 ● LEFT/ RIGHT/ MENU/ OK button 50 ● LCD .
《5》 Getting to know your camera Thank you for buying a Samsung Digital Camera. ● Prior to using this camera, please read the user manual thoroughly. ● When you require After Sales service, please bring the camera and the cause of the camera malfunction (such as Batteries, Memory card etc.
《6》 Danger ■ Do not use the flash in close proximity to people or animals. Positioning the flash too close to your subject’s eyes, may cause eyesight damage. ■ When taking photographs, never point the lens of the camera directly into very strong light.
《7》 Caution An FCC warning • This device has been tested in accordance with the limits of a class B digital device under item 15 of the FCC rules. These limits are designed to provide protection against harmful interference in commercial installation.
《8》 System chart Please check that you have the correct contents before using this product. To buy the optional equipment, contact your nearest Samsung dealer or Samsung service centre. Pouch User manual Product warranty Camera strap Software CD (see p.
《9》 System chart USB cable PictBridge compatible printer(see p.63) Computer (see p.95) For Windows • PC with processor better than MMX Pentium 233MHz (XP: Pentium II 300MHz) • Windows 98/ 98SE.
《10》 Identification of features Front & T op Back & Bottom Tripod socket LCD monitor Mode button Play mode button 5-function button LCD button Zoom T button (Digital zoom) Camera status la.
《11》 Identification of features A movie clip can be recorded for as long as the available recording time of the memory capacity allows. Image size and type are listed below.
《12》 Identification of features ■ Self-timer lamp Icon Status Description For the 2 seconds, the lamp blinks quickly at 0.25-second intervals. ■ Camera Status Lamp Status Description Power on .
《13》 Instructions on how to use the power source ■ You can use batteries only to provide the camera with power. ● We recommend using batteries for a digital camera (Within a year from the date of manufacture).
《14》 Connecting to a Power Source 3. To close the battery chamber cover, push it until it clicks. 2. Insert the batteries taking note of the polarity (+/ -).
《15》 Instructions on how to use the memory card ● Be sure to format the memory card (see p.72) if you are using a newly purchased memory for the first time, if it contains data that the camera cannot recognize, or if it contains images captured with a different camera.
《16》 Instructions on how to use the memory card ■ The camera can use SD Memory Cards and MMC (Multi Media Card). Mode STILL IMAGE mode MOVIE CLIP mode Quality/ Size 2560(P) 2048 1600(M) 1024 640.
《17》 Inserting the memory card 1. Turn the power off using the power button. Open the battery chamber cover and press the memory card as shown in the image and release. 2. Remove the memory card and close the battery chamber cover. 3. To close, push the battery chamber cover until you hear a click.
《18》 LCD monitor indicator ■ The LCD monitor displays information about the shooting functions and selections. [ Image & Full Status ] No. Description Icons Page 1 Battery p.14 3 Continuous shot p.40 4 Flash p.26 5 Self-timer p.28 6 Macro 7 Metering p.
《19》 LCD monitor indicator 13 ISO p.31 14 Sharpness p.42 15 Image quality p.38 16 Image size 2560, 2048, 1600, 1024, 640 p.37 Number of available shots remaining 18 Remaining time (Movie clip/ Voice recording) 00:01:11/ 00:25:50 18 Voice memo p.25 19 Digital Zoom rate 17 Starting the recording mode ● Taking a still image 1.
《20》 Starting the recording mode ● Recording a Movie clip Steps from 1-4 are the same as those for taking a still image. 5. Select the MOVIE CLIP mode by pressing the mode button. 6. Point the camera towards the subject and compose the image by using the LCD monitor.
《21》 Starting the recording mode [ Pausing the voice recording ] PAUSE STOP:SHUTTER ● Pausing while recording a voice recording This camera allows you to temporarily stop during unwanted recording, while recording a voice.
《22》 Starting the recording mode ■ When the Flash Off or Slow synchro mode is selected in a low lighting condition, the camera shake warning indicator ( ) may appear on the LCD monitor. In this case, use a tripod, support the camera on a solid surface or change the flash mode to flash shot mode.
《23》 Using the camera buttons to adjust the camera ■ The RECORDING mode function can be set up by using the camera buttons. ● Used for turning the camera’s power on / off. ● If this camera isn’t operated during the specified time (about 60 SEC.
《24》 ZOOM W/T button ● TELE Zoom Digital zoom TELE : Pressing the ZOOM T button activates the digital zoom software. Releasing ZOOM T button stops the digital zooming at the required setting. Once the maximum digital zoom (5X) is achieved, pressing the ZOOM T button will have no effect.
《25》 V oice memo( )/ UP button ■ While the menu is showing, press the UP button to move up the submenu cursor. ■ When the menu is not displayed on the LCD monitor, the UP button operates as the voice memo button. You can add your voice-over to a stored still image.
《26》 Flash ( )/ Left button [ Selecting the auto flash ] ● Flash range ■ When the menu is displayed on the LCD monitor, pressing the LEFT button makes the cursor shift to the left tab. ■ When the menu is not displayed on the LCD monitor, the LEFT button operates as the FLASH ( ) button.
《27》 Flash ( )/ Left button Icon Flash mode Description ● Flash mode indicator If the subject or background is dark, the camera flash will operate automatically.
《28》 Self-timer ( )/ Right button ● Selecting the self-timer 1. Select the MOVIE CLIP or STILL IMAGE mode by pressing the mode button. 2. Press the SELF-TIMER button until the desired mode indicator displays on the LCD monitor. A 2 second, 10 second or double self-timer icon appears on the LCD monitor.
《29》 MENU/ OK button - When you press the MENU button, a menu related to each camera mode will be displayed on the LCD monitor. Pressing it again will return the LCD to the initial display. - A menu option can be displayed when the following are selected : MOVIE CLIP and STILL IMAGE mode.
《30》 +/- button ■ You can use the +/- button to adjust the values for the white balance, ISO, exposure compensation, shutter speed and aperture value.
《31》 +/- button ● Using the Custom White Balance White balance settings may vary slightly depending on the shooting environment. You can select the most appropriate white balance setting for a given shooting environment by setting up the custom white balance.
《32》 +/- button ■ Setting up the shutter speed and aperture value : This camera automatically adjusts the shutter speed and aperture values to the shooting environment. However, in Night scene mode, you can set the shutter speed and aperture values to your preference.
《33》 +/- button [ Image & full information ] [ Image & basic information ] [ LCD off ] ■ You can check the recording status in the LCD monitor. Pressing the LCD button in the RECORDING (STILL IMAGE, MOVIE CLIP) mode will change the display as shown below.
《34》 Menu tab Main menu Sub menu Camera working mode Page AUTO PROGRAM NIGHT PORTRAIT LANDSCAPE FIREWORKS 2560X1920(P) 2048X1536 1600X1200(M) 1024X768 640X480(E) 640X480 320X240 S.FINE FINE NORMAL 15FPS 24FPS MULTI SPOT Using the LCD monitor to adjust the camera settings ■ You can use the menu on the LCD monitor to set up recording functions.
《35》 Using the LCD monitor to adjust the camera settings Menu tab Main menu Sub menu Camera working mode Page SINGLE 2, 4, 8 SHOTS NORMAL B&W SEPIA OFF 1~9 SOFT NORMAL VIVID SHOOTING EFFECT P.FRAME SHARPNESS MYSET p.40 p.40 p.41 p.42 p.43 * Menus are subject to change without prior notice.
《36》 How to use the menu 3. Use the UP and DOWN buttons to select a sub menu. 4. Select a sub menu, and then the value you set will be saved. Press the MENU button and the menu will disappear. 1. Turn on the camera and press the MENU button. A menu for each camera mode appears.
《37》 Size ■ You can select the image size appropriate for your application. Mode Icon 2560 2048 1600 1024 640 640 320 Size 2560X1920 2048X1536 1600X1200 1024X768 640X480 640X480 320X240 STILL IM.
《38》 Quality ■ You can select the compression ratio appropriate for your application of the captured images. The higher the compression ratio, the lower the picture quality.
《39》 Metering ■ If you cannot obtain suitable exposure conditions, you can change the metering method to take brighter pictures. [MULTI]( ) : Exposure will be calculated based on an average of the available light in the image area. However, the calculation will be biased towards the centre of the image area.
《40》 Continuous shot ■ By using the camera’s digital processor, it is possible to add special effects to your images. [ PROGRAM mode ] [ MOVIE CLIP mode ] NORMAL : No effect is added to the image. B & W : Converts the image to black and white.
《41》 Photo Frame ■ You can add 9 types of frame-like borders to a still image you want to capture. - If you select the [OFF] sub menu in the [P.FRAME] menu or turn on and off the camera in the PROGRAM mode, the selected photo frame will be cancelled.
《42》 Sharpness ■ You can adjust the sharpness of the picture you want to take. You cannot check the sharpness effect on the LCD monitor before you take a picture, because this function is applied only when the captured image is stored on the memory.
《43》 Save / Load the camera configuration (MYSET) 1. Press the MENU button and select [MYSET] menu by pressing the LEFT/RIGHT button. 2. Press the UP/DOWN buttons to select the [SAVE] menu and press the right button. 3. Press the UP/DOWN buttons to select desired MYSET slot number to save.
《44》 LCD monitor indicator ■ The LCD monitor displays information about the shooting conditions. 100-0009 ① ⑦ ② ③ ④ ⑤ ⑥ No. Description Icon Page 1 Battery p.14 2 Play mode 3 File Type 4 Voice memo p.48 5 Protect indicator p.58 6 DPOF indicator p.
《45》 Starting play mode ■ If the memory card is inserted in the camera, all the camera functions apply only to the memory card. ■ If the memory card is not inserted in the camera, all the camera functions apply only to the internal memory.
《46》 Starting play mode ● Playing back a movie clip Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded movie clip that you want to play back by using the LEFT/ RIGHT button. If you select a movie clip, the movie clip indicator ( ) will be displayed on the LCD monitor.
《47》 Using the camera buttons to adjust the camera ■ In Play mode, you can use the buttons on the camera to conveniently set up the Play mode functions. ● Image enlargement 1. Select an image that you want to enlarge and press the enlargement button.
《48》 Thumbnail( )/ Enlargement( ) button ● The maximum enlargement rate in proportion to the image size. ● Trimming : You can extract part of the image that you want and save it separately. 1. Select an image that you want to enlarge and press the enlargement button.
《49》 V oice ( ) memo/ Up button 3. Press the shutter button to start recording and voice will be recorded to the still image for 10 seconds. While the voice is recording, the recording status window will be displayed as shown alongside. 4. The recording can be stopped by pressing the shutter button again.
《50》 LEFT/ RIGHT/ MENU/ OK button ■ LEFT/ RIGHT/ MENU/ OK buttons activate the following. - LEFT button : While the menu is showing, press the LEFT button to select the menu tab to the left of the cursor.
《51》 Delete( ) button ■ This deletes images stored on the memory card. ● Before deleting images from the camera, you should protect or download images to your computer that you wish to keep.
《52》 Setting up the play back function using the LCD monitor ■ PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in Play mode are as follows.
《53》 Setting up the play back function using the LCD monitor ■ This menu is available while the camera is connected to a PictBridge supporting printer (direct connection to the camera, sold separately) with a USB cable.
《54》 Setting up the play back function using the LCD monitor ※ Menus are subject to change without prior notice. Menu tab Main menu Sub menu Secondary menu Page AUTO PLAIN PHOTO FAST PHO. AUTO DRAFT NORMAL FINE AUTO OFF ON AUTO OFF ON NO - YES - CUSTOM SET p.
《55》 Starting the slide show ■ Images can be displayed continuously at pre-set intervals. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [SLIDE] menu tab. ● Setting play interval: Set the slide show play interval.
《56》 Rotating an image ■ You can rotate the stored images by various degrees. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [ROTATE] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button.
《57》 Resize ■ Change the resolution (size) of pictures taken. Select [LOGO] to save an image to be the start-up image. The resized image will have a new file name. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [RESIZE] menu tab.
《58》 Protecting images ● Protecting Images 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [PROTECT] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
《59》 Deleting all images DPOF ■ Of all the files stored in the memory card, the unprotected files in the DCIM subfolder will be deleted. Remember that this will permanently delete unprotected images. Important shots should be stored on a computer before deletion takes place.
《60》 DPOF : ST ANDARD ■ This function allows you to embed print quantity information on a stored image. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [STANDARD] menu by pressing the UP/ DOWN button and press the RIGHT button.
《61》 DPOF : PRINT SIZE DPOF : CANCEL ■ You can specify the print size when printing images stored on the memory card. The [SIZE] menu is available only for DPOF 1.1 compatible printers. ■ You can cancel the [STANDARD], [INDEX], or [SIZE] settings.
《62》 COPY T O CARD ■ This enables you to copy image files to the memory card. ● Copying to the Memory Card 1. Press the play mode button and press the menu button. 2. Select the [COPY TO CARD] menu tab by pressing the LEFT/ RIGHT button. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
《63》 PictBridge ※ If you selected [COMPUTER] in Step 5, when you connect the camera to your printer, the camera status lamp(Green) will illuminate and the connection will not be established. In this case, disconnect the USB cable, and then follow the procedure from Step 2 and onward.
《64》 PictBridge: Picture Selection ■ Select pictures to print 1. Connect the camera to your printer. The USB menu must be set to [PRINTER] before you connect the camera to the printer.(See p.63) 2. The [IMAGES] menu will appear. 3. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button.
《65》 PictBridge: Printing ■ Printing Pictures 1. Connect the camera to your printer. The USB menu must be set to [PRINTER] before you connect the camera to the printer.(See p.63) 2. Use the LEFT and RIGHT buttons to select the [PRINT] menu tab. 3.
《66》 PictBridge: Print Setting ■ AUTO SET 1. Connect the camera to your printer. The USB menu must be set to [PRINTER] before you connect the camera to the printer.(See p.63) 2. Use the LEFT and RIGHT buttons to select the [AUTO SET] menu tab. 3.
《67》 PictBridge : RESET ■ Initializes user-changed configurations. 1. Connect the camera to your printer. The [USB] menu must be set to [PRINTER] before you connect the camera to the printer.(See p.63) 2. Use the LEFT and RIGHT buttons to select the [RESET] menu tab.
《68》 Setup menu ■ In this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording mode. The items indicated by are default settings. ■ The OK button written in this manual means the MENU button.
《69》 Setup menu * Menus are subject to change without prior notice. ■ This function allows the user to select the file naming format. ● Assigning File Names 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab.
《70》 File name ● The first stored folder name is 100SSCAM, and the first file name is S5020001. ● File names are assigned sequentially from S5020001 → S5020002 → ~ → S5029999. ● The folder number is assigned sequentially from 100 to 999 as follows: 100SSCAM → 101SSCAM → ~ → 999SSCAM.
《71》 Language ● Setting Language 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab. 3. Select the [LANGUAGE] menu by pressing the UP/ DOWN button and press the RIGHT button.
《72》 Formatting a memory card ● Formatting a Memory Card 1. In any mode other than Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab. 3. Select the [FORMAT] menu by pressing the UP/ DOWN button and press the RIGHT button.
《73》 Setting up the Date ■ You can change the date that will be displayed on the captured images. ■ You can change the time that will be displayed on the captured images. ● Setting Date 1. In any mode with the exception of Voice Recording mode, press the MENU button.
《74》 Date type ■ You can change the date type that will be displayed on the captured images. ● Setting up the Date type 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab.
《75》 Beep ■ You can select an external device to which you want to connect the camera using the USB cable. ● Selecting an External Device 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab.
《76》 Quick view ■ If you enable Quick View before capturing an image, you can view the image you just captured on the LCD monitor for the duration set in the [Q.VIEW] setup. Quick view is possible only with still images. ● Setting Quick View 1.
《77》 Setting up the MYCAM menu ■ You can set up a start up image and start up sound. Every camera working mode (with the exception of Voice recording mode) has the MyCAM menu. The items indicated by are default settings. Menu tab Main menu Sub menu Page OFF IMAGE 1 IMAGE 2 USER IMAGE OFF ON S.
《78》 Start up sound ■ You can select the sound that is activated whenever the camera is turned on. ● Setting the Startup Sound 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [MYCAM] menu tab.
《79》 Important notes Be sure to observe the following precautions! ■ This unit contains precision electronic components. Do not use or store this unit in the following locations. - Areas exposed to severe changes in temperature and humidity. - Areas exposed to dust and dirt.
《80》 Important notes ■ Caution on Using the Lens - If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of the image sensor. - Pay attention not to get fingerprints or foreign substances on the surface of the lens.
《81》 W arning indicator ■ There are several warnings that may appear on the LCD display CARD ERROR ! ㆍ Memory card error → Turn off the camera power and turn it on again → Insert the memory card again → Insert the memory card and format the memory card (p.
《82》 W arning indicator The camera doesn’t switch on ㆍ There is low battery capacity → Insert fresh batteries ㆍ Batteries are inserted incorrectly with the reverse polarities → Insert th.
《83》 Before contacting a service centre Camera does not take images when pressing the Shutter button ㆍ There is insufficient memory capacity → Delete unnecessary image files ㆍ The memory card has not been formatted → Format the memory card (p.
《84》 Before contacting a service centre The images don't play back ㆍ Incorrect file name (Violation of DCF format) → Do not change the image file name Colour of image is different to the .
《85》 Specifications Type 1/2.5" CCD Effective Pixels Approx. 5.0 Mega-pixel Total Pixels Approx. 5.2 Mega-pixel Lens f = 5.8mm (35mm film equivalent: 35mm) F No. F 3.5/ F7.0 Still Image mode: 1.0X ~ 5.0X Play mode: 1.0X ~ 7.0X (depends on Image size) 1.
《86》 Specifications 2560 : 2560 x 1920 2048 : 2048 x 1536 1600 : 1600 x 1200 1024 : 1024 x 768 640 : 640 x 480 2560 : Super fine (9) Fine (18) Normal (29) 2048 : Super fine (13) Fine (27) Normal (.
《87》 Software Notes Please ensure that you read the instruction manual carefully before use. ㆍ The attached software is a camera driver and image editing software tool for Windows. ㆍ Under no circumstances should all or part of either the software or the user manual be reproduced.
《88》 About the software After inserting the CD-ROM provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver. ■ Camera driver : This enables images to transfer between the camera and PC.
《89》 Setting up the application software To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. You can visit the Samsung web-site through the internet.
《90》 Setting up the application software 3. A window for which you can select application software will be displayed. Select the application program and click the [Install] button. Refer to page 88 for more information about the application program.
《91》 Setting up the application software 8. Digimax Viewer installation is successfully completed. Click the [Finish] button to install PhotoImpression. The system will not reboot even if the [Yes, I want to restart the computer now] option is selected.
《92》 Setting up the application software 12. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse...] and choose a folder you want. 13. The [Select Components] window will appear. Click [Next >] button.
《93》 16. After restarting the computer, connect the PC to the camera with the USB cable. 17. Turn the camera power on. [Found New Hardware Wizard] will open and the computer will recognise the camera. * If you have ever installed an image viewer program or your OS is Windows XP, an image viewer program will open.
《94》 Setting up the application software ● If you have installed the camera driver, [Found New Hardware Wizard] may not open. ● On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens and a window asking you to select a driver file may appear.
《95》 Starting PC mode • If you connect the USB cable to a USB port on your PC and then turn on the power, the camera will automatically switch to "computer connection mode". • In this mode, you can download stored images to your PC through the USB cable.
《96》 Starting PC Mode ■ Downloading stored images You can download the still images stored on the camera to your PC's hard disk and print them or use a photo editing software to edit them. 1. Connect the camera to your PC with the USB cable.
《97》 Starting PC Mode 7. An image file is transferred from the camera to your PC. 6. Press the right mouse button and a pop-up menu will open. Click [Paste]. - By using [Digimax Viewer], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.
《98》 Removing the USB Driver for Windows 98SE ■ To remove the USB driver, refer to the process shown below. 1. Trace [Start → Settings] and click [Control Panel]. [Click!] 4. Uninstallation is complete. Click the [Yes] button and the window will disappear.
《99》 Removable Disk ■ To use this camera as a Removable Disk, install (p.89) the USB Driver. 1. Before turning the camera power on, connect the camera to the PC with the USB cable. 2. Click [Removable Disk] under [My computer] or [Windows Explorer].
《100》 Removing the removable disk ■ Windows 98SE 1. Check whether the camera and PC are transferring a file. If the camera status lamp blinks, you have to wait until the lamp illuminates. 2. Unplug the USB cable. ■ Windows 2000/ME/XP (The illustrations may be different from the real display in accordance with the Windows O/S.
《101》 Removing the removable disk 6. A [Unplug or Eject Hardware] window will open. Click the [Close] button and the removable disk will be removed safely. 7. Unplug the USB cable. [Click!] 1. A USB Driver for MAC is not included with the software CD as MAC OS supports the camera driver.
《102》 Digimax V iewer 2.1 ■ This software is only compatible with Windows. 1. To open Digimax Viewer, click the [Start → Programs → Samsung → Digimax Viewer 2.1 → Digimax Viewer 2.1 ] and Digimax Viewer 2.1 will then open. 3. You can easily use the Digimax viewer 2.
《103》 Using PhotoImpression With PhotoImpression, you can edit or store still images that you downloaded from the camera. This software is only available in Windows version. To start the program, click [Start → Programs → ArcSoft PhotoImpression → PhotoImpression].
《104》 Using PhotoImpression ■ Tool Bar Button Description Button Description Resize Layer Flip Layer Horizontally Undo Copy Delete Layer Rotate Layer Rotate All Layers Redo Paste Close Picture ● For detailed instructions on how to use PhotoImpression, please refer to the program's Help.
《105》 FA Q [Case 4] The camera is not recognised by your PC. Sometimes, the camera may appear under [Unknown Devices] in Device Manager. → Install the camera driver correctly. Turn off the camera, remove the USB cable, plug in the USB cable again, and then turn on the camera.
《106》 FA Q [Case 9] When I open the Device Manager (by clicking Start → (Settings) → Control Panel → (Performance and Maintenance) → System → (Hardware) → Device Manager), there are 「 Unknown Devices 」 or 「 Other Devices 」 entries with a yellow question mark(?) beside them or devices with an exclamation mark(!) beside them.
《107》 FA Q ● If a PC (Windows 98) stops responding while the camera and PC are connected repeatedly → If a PC (Windows 98) is turned on for a long time and connect the camera repeatedly, the PC may not recognise the camera. In this case, re-start the PC.
6806-2751 SAMSUNG TECHWIN CO., LTD. OPTICS & DIGITAL IMAGING DIVISION 145-3, SANGDAEWON 1-DONG, JUNGWONGU, SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121 TEL : (82) 31-740-8086,8088, 8090, 8092, 8099 FAX : (82) 31-740-8398, 8111 www.samsungcamera.com SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
An important point after buying a device Samsung A502 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Samsung A502 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Samsung A502 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Samsung A502 you will learn all the available features of the product, as well as information on its operation. The information that you get Samsung A502 will certainly help you make a decision on the purchase.
If you already are a holder of Samsung A502, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Samsung A502.
However, one of the most important roles played by the user manual is to help in solving problems with Samsung A502. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Samsung A502 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
