Instruction/ maintenance manual of the product PRO-9342FT3WOS2 Audiovox
Go to page of 8
Model PRO-9342FT3WOS2 Owner's Manual FEA TURES: w 2 Three Button Programmable RF T ransmitters w Three Channel Receiver (capable of accepting 4 transmitters) w Anti-scan T echnology w Remote Pani.
ARMING THE SYSTEM - ACTIVE 1. Turn of f the engine, exit the vehicle and close all doors, hood lid, and trunk lid. 2. Press and release the Arm / Lock button on the keychain transmitter . þ Red dash mounted LED begins to flash slowly . þ Parking Lights flash one time.
Page 3 sound. The alarm will continue to sound for 30 seconds, then stop and continue to monitor all protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone. þ Whenever the system is armed, the red dash mounted LED indicator will slowly flash.
Page 4 Open any door to suspend the automatic arming. þ Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered.
Page 5 3. T o return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE : Always remember to return the system to the NON V ALET mode after servicing to ensure that the vehicle remains protected at all times.
Page 6 NOTE: If 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: T o Change the code from the factory pre-assigned code of 1 1 to “52” you would do the following: 1.
ELIMINA TING THE NORMAL ARM / DISARM CHIRPS As explained earlier in the manual, you can eliminate the chirps selectively any time you arm or disarm the system simply by holding the ARM / DISARM button for two seconds.
DASH LED INDICA TORS RAPID FLASHING = P ASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = V ALET MODE 3 FLASH...P AUSE = INTRUSION ZONE 3 2 FLASH.
An important point after buying a device Audiovox PRO-9342FT3WOS2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox PRO-9342FT3WOS2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox PRO-9342FT3WOS2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox PRO-9342FT3WOS2 you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox PRO-9342FT3WOS2 will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox PRO-9342FT3WOS2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox PRO-9342FT3WOS2.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox PRO-9342FT3WOS2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox PRO-9342FT3WOS2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
