Instruction/ maintenance manual of the product RSH Series Royal Sovereign
Go to page of 10
19 RSS, RSR and RSH Series Laminator OWNER'S MANUAL Royal Sovereign International Inc. 18. W ARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and.
RSS, RSR, RSH Series 2 1 T ABLE OF CONTENTS 1. INTRODUCTION TOPIC P AGE 1. Introduction .......................................................................................................... 2 2. Safety Precautions ................................
RSS, RSR, RSH Series 4 3 3. INST ALLA TION Note: The laminator should be installed by a trained service technician. ELECTRICAL REQUIREMENTS The laminator comes fully assembled, except for the feed table and paper guide to avoid shipping damage. Upon arrival, thoroughly inspect the unit.
RSS, RSR, RSH Series 6 5 5. PRODUCT IDENTIFICA TION 6. CONTROL P ANEL 1 15 2 3 4 5 6 7 8 14 13 10 9 12 11 No. PART NAME RSS-685/ RSS-1050/ RSR-685 RSR-1050 RSH-1050 RSH-1650 RSS-685N RSS-1050N 1 FILM .
RSS, RSR, RSH Series 8 7 Control Buttons 1. UPPER : To change upper roller temperature by pressing button, then up or down arrow. (range 32~320°F or 0~160°C) 2. LOWER : To change lower roller temperature by pressing button, then up or down arrow. (range 32~320°F or 0~160°C) 3.
RSS, RSR, RSH Series 10 9 9. USING FOOT PEDAL AND REMOTE CONTROL 10. USING CROSS CUTTER USING FOOT PEDAL Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed, you may use the foot pedal to operate the laminator for “Hands Free Operation.
RSS, RSR, RSH Series 12 11 12. LOADING FILM 13. THREADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). Loading films to upper and lower film shafts: (See page 5 for assistance with parts identification.
RSS, RSR, RSH Series 14 13 Figure 4 Figure 5 10. Reinstall the Front Table and the Paper Guide, and close the Safety Cover. 11. Adjust the nip setting to 1/8´ ´ (3mm). 12. Insert and push the leader boards on each end until boards reach the front nip point.
RSS, RSR, RSH Series 16 15 Figure 1 1. Lay the decaled image face down on a flat surface. Carefully peel back and put a crease along the edge of the release liner (Approximately 1 in or 25mm, Figure 1). 2. With the image facing up, align the image onto the board.
RSS, RSR, RSH Series 18 17 15. MAINTENANCE 17. SPECIFICA TIONS 16. TROUBLESHOOTING Cleaning the Body of the lamina t or 1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean. Removing Adhesive Build Up 1. Remove the film from the laminator.
An important point after buying a device Royal Sovereign RSH Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Royal Sovereign RSH Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Royal Sovereign RSH Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Royal Sovereign RSH Series you will learn all the available features of the product, as well as information on its operation. The information that you get Royal Sovereign RSH Series will certainly help you make a decision on the purchase.
If you already are a holder of Royal Sovereign RSH Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Royal Sovereign RSH Series.
However, one of the most important roles played by the user manual is to help in solving problems with Royal Sovereign RSH Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Royal Sovereign RSH Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
