Instruction/ maintenance manual of the product RAS10 Rimage
Go to page of 20
Rimage AutoPrinter™ User Guide This manual provides the informatio n ne eded to operate the AutoPrinter and identify the parts. To setup and install your AutoPrinter, refer to the Setup and Installation Guide in cluded with your product .
.
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 0004 (International) Fax: +1 952 944 6956 European Hea.
Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washingt on Aven ue South Minneapolis, MN 55439 USA Attn: Rimage Services Service: North America: 800-553-8312.
Contents Contents Introduction ...................................................................................... 1 Operating system requirements ............................................................................ 1 Media requirements ...
Rimage AutoPrinter™ User Guide . ii.
Introduction Introduction This manual provides the information ne eded to oper ate the AutoPrinter and identify the parts. To setup and install your AutoPrinter, refer to the Setup and Installation Guide included with you r product . Note: The term AutoPrinter applies to both the AutoEveres t and the AutoPrism.
Rimage AutoPrinter 2 110656_H Identify the parts of the AutoPrinter Front view Lift Arm Lift Arm Prism Printer Everest Printer Control Panel Control Panel Operator Panel Operator Panel Carousel Carous.
Identify the parts of the AutoPrinter Operator panel The operator panel has four indicator lig hts and an operator button. Operator button Each time you press the operator button , the carousel rotates to the next bin.
Rimage AutoPrinter 4 110656_H Rear view Printer Control Cable Everest Printe r USB Cable Printer Control Cable USB Cable Prism Printer Prism Power S wi tc h Serial Cable* Power Sw it ch Power Sw it ch AutoEverest AutoPrism *Serial cable is used only for updating the firmware.
Operate the AutoPrinter Operate the AutoPrinter Installing the carousel - Important: To prevent errors, the carousel should be installed before op erating the software or powering on the AutoPrinter. 1. Slide the carousel into the unit so that the shaft slides in the slot opening of the bearing guide .
Rimage AutoPrinter 6 110656_H Loading and unloading discs You can load up to 100 discs per carousel bin. You may load discs in the bins before installi ng the carousel. When the carousel is installed in the AutoPrinte r, discs ca n be in stalled one bin at a time by following the procedure below.
Maintain the AutoPrinter Maintain the AutoPrinter Installing ribbons Before installing ribbons in the printe r, stop any ope rations. To change ribbons in a Prism printer, refer to the PrismP lus Printer User Guide . To change ribbons in an Everes t II printer, refer to the Everest II Printer User Guide .
Rimage AutoPrinter 8 110656_H 4. Align the printer. a. Slowly slide the lift arm down until the disc just touches the print pad. b. If the disc is not centered on the print pad, align the printer side to side. Printer Button Lift Arm Side to Side Alignment i.
Maintain the AutoPrinter Prism printer To align your Prism printer, use the following in stru ctions. # Required tools: • T25 Torx screwd riv er • 5/32” Allen wrench 1. Power on the AutoPrinter . Note: If the Prism power switch is in the on position, power on both the printer and the pow er sw itch .
Rimage AutoPrinter 10 110656_H b. If the disc is not centered on the print pad, align the printer side to side. i. Using the T25 Torx screwdriver, loosen the two side to side alignment screws . ii. Slide the printer , not the printer tray, until the side edges of the disc and printer pad are aligned.
Learn More Learn More AutoPrinter specifications Note: Specifications for the printe r are in the printer user guide. AutoPrinter autoloader, a Rimage Everest or Prism printe r, and CD Designer software suite.
Rimage AutoPrinter 12 110656_H n rning is at could resu lt in bodily injury to personnel operating or p e this guideline could result in loss or damage to the re, or data.
Learn More Safety testing Product name: AutoPrinter Model: RAS10 Notice for USA Tested to Comply with FCC Standards FO R HOME OR OFFICE USE. NOTE: This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursuant to Part 15 of the F CC Rules.
Rimage AutoPrinter 14 110656_H Rimage AutoPrinter II Li mited One Year Warranty Rimage warrants, to the origi nal end user only , that all non-consum able parts of the AutoPrinter III will be free fro.
An important point after buying a device Rimage RAS10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Rimage RAS10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Rimage RAS10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Rimage RAS10 you will learn all the available features of the product, as well as information on its operation. The information that you get Rimage RAS10 will certainly help you make a decision on the purchase.
If you already are a holder of Rimage RAS10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Rimage RAS10.
However, one of the most important roles played by the user manual is to help in solving problems with Rimage RAS10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Rimage RAS10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
