Instruction/ maintenance manual of the product RLDED3950A RCA
Go to page of 40
RLDED3950A 39” LED TV USER ’ S M ANUA L.
1 Contents Intr oduction Wa r n i n g Caution Important Information Attaching or Removing the S tand Installing Batteries to the Remote Contr ol Identifying Fr ont and Rear.
2 Intr oduction Thank you very much for purchasing your LED TV. It serves as a normal colour TV and a PC monitor . T o enjoy your set fully from the very beginning, read this manual carefully and keep it handy for future reference. INST ALLA TION ① Lo cate the r ecei ver in the room where dir ect li ght does not strike the scr ee n.
3 W ar ni ng This symbol is intended to alert the user to avoid the risk of electric shock. This equipment may only be disassembled by qualified service personnel. This symbol is intended to alert the user to the presence of i mpor ta n t oper ati on a nd mai n te nan ce instru cti ons in the literature accompanying the equipment.
4 Caution Caution High voltages are used in the operation of this product. - Do not open the product's casing. Refer servicing to qualified service personnel .
5 Caution Caution Never stand on, lean on or suddenl y push the product or its stand. Y ou should pay special attention to c h i l d r e n . Caution Do not place the main unit on an unstable cart stand, shelf or table. Serious injury to an individual and damage to the television may result if it should fall.
6 Television Antenna Connection Protection Important Information External T e levision Antenna Grounding If an outside antenna or cable system is to be c onnected to the TV , make sure that the antenna or cable system is electrically grounded to prov ide some protection against voltage sur ges and static charges.
7 Attacthing or Removing the Stand 1. T o attach the base place the display unit flat on a table. Afterwards attach the stand onto the bottom of the stand.
8 2. T o remove the stand, remove the 4 screws in the area and the stand will come off. Installing Batteries to the Remote Control Please insert two AAA batteries into the remote control. Make sure that you match the (+) and (-) symbols on the batteries with the (+) and (-) symbols inside the battery compartment.
9 Front View Rear View Mounting Pattern Identifying Front and Rear Panel INDICA TOR LIGHT – The li ght is red when power is plugged in but the TV is not turned on. The light turns blue when the TV is turned on. Because of the LED in the panel, the TV might take 10 – 12 seconds to power on.
10 If You Have Digital Ca bl e w i thou t Cable Box or Anten na… Connection Suggestions 1. Make sure the power of HDTV is turned of f. 2. Connect the RF cable from yo ur antenna or digital cable to the TV port on the back of your HDTV . 3. T u rn on the HDTV .
11 Co nnecting DVD Player with Compo nent YPbPr… 1. Make sure the power of HDTV and your DVD player is turned off. 2. Obtain a Component Cable. Connect the green color connector to both your DV D player and YPbPr’ s green connector port on the back of your HDTV .
12 Connectin g Wii™ with Composite… 1. Make sure the power of HDTV and your W ii™ is turned off. 2. Obtain a Y ellow V ideo Cable. Connect the Y ellow V ideo connector to both your W ii™ and A V’ s Y ellow V ideo connector port on the back side of your HDTV .
13 Connectin g Cable or Satellite boxes with HDMI… 1. Make sure the power of HDTV and your set-top box is turned of f. 2. Connect a HDMI cable to the HDMI output of your set-top box and the other en d to the HDMI port on the back of your HDTV . 3. T urn on the HDTV and your set-top box.
14 Connecti ng to a PC with VGA and 3. 5 mm minijack … 1. Make sure the power of HDTV and your PC is turned off. 2. Obtain a 15-pin D-Sub VG A cable; connect to the VGA output of your PC and the other end to the VGA port on the back of your HDTV . 3.
15 Connecting a Digital Audio Receiver with Coaxial... 1. Make sure the power of HDTV and y our receiver is turned off. 2. Obtain a COAXIAL cable, connect it to your receiver’s COAXIAL digital input and the COAXIAL connection on the LINE OUT port on the back of the HDTV .
16 Main unit description Contr o l Panel Button Function TV T erminal Connections 1. Coaxial ou t term inal. 2. RF antenna. 3. VGA input terminal of simulation signal of PC. 4. PC AUDIO input terminal. 5. V ideo input terminal. 6. AUDIO input terminal （ Audio input terminal for Component and V ideo ） .
17 Remote contr ol POWER : Power on/off button , press once to turn the TV on and press again to turn the TV off. MUTE: Press this button to mute or restore sound. MTS/AUDIO : When stereo program is r eceived, press this key to switch sound system between m ono and stereo .
18 Installa tion Guide Press M ENU button to display th e MAIN OSD MENU ; Press ◄ / ► button to select the MENU you want; Press ENTER button to enter the sub menu ; Press ▼ / ▲ button to selec.
19 Press ▼ / ▲ but ton to se lect Brightness , then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Contrast , then press ◄ / ► button to ad just. . Press ▼ / ▲ button to select Color , t hen press ◄ / ► button to ad just.
20 Press ▼ / ▲ button to select Auto Adjust , then press ENTER button to start auto adjusting. Press ▼ / ▲ button to select Horizontal Position , then press ◄ / ► button to adjust. Press ▼ / ▲ button to select Vertical Position , then press ◄ / ► button to adjust.
1 2 SOUND Sound Settings Press ENTER when th e So u nd S e tt i ng s i te m is hi ghlighte d. Then yo u will go to the sub- m e nu as follo wing. Press ▼ / ▲ to se l ec t the de sired m e nu i te m . Press E N TER to p r oce ed if n e cessar y. Press / to adjust the i te m the d esired le v el .
2 2 AVL Press ▼ / ▲ button to select the item AVL, then press ENTER button to adjust. Analog Sound Press ▼ / ▲ bu tton to sel ec t the ite m P referred A na l og S ou n d, t hen pre ss ◄ / .
23 Channel List Press ▼ / ▲ b utton to se lect Channel List, then press enter scan th e Channel List. If you sele ct the press enter button t o option “In Chan nel List” On, the ch annel label will display in the lis t. Favorite List Press ▼ / ▲ butto n to select Favorite List, then press ENTER button to scan the Favorite Channel List.
4 2 Sk ip Set th e channe l to be s kippe d wh en u sing CH+/Ch- to vi ew ch anne ls . Favorite Set th e channe l to y our f a vo r ite lis t . Label Rena me lab el of the cha nn el . Signal Type Press ▼ / ▲ bu tto n to s el ec t S ign al Type, then pr e ss butt on ◄ / ► to s ele ct the type y ou w ant to s et .
25 PARENTAL CONTROL Input password to enter, default password is “0000”. V-CHIP Press ▼ / ▲ button to select V-CHIP, then press ENTER b utton to adjust.
26 US V-CHIP Press ▼ / ▲ button to select US V-CHIP , then press ENTER button to adjust. A Sub Menu Will appear as below. Movie Rating Press ▼ / ▲ button to se lect Movie Rating , then press ENTER button to adjust. A Sub Menu Will appear as below.
27 CANADA V-CHIP Press ▼ / ▲ button to select CANADA V-CHIP , then press ENTER button to adjust. A Sub Menu Will appear as below. The operation of CANADA V-CHIP is the same as the operation of US V-CHIP. Block Unrated Show Press ▼ / ▲ but ton to se lect Block Unrated Show , then press ENTER butto n to set the ratin g locked .
28 Clear Do wnloadable Data Press ▼ / ▲ but ton to se lect Clear Downloadable Data , then press ENTER butt on to set the rating. Note : The above two opera tion only va lid when play ing the dow nloadable data stream. The operations are the same as US V-CH IP.
29 Setup Menu Closed Caption Press ▼ / ▲ button to se lect the item Closed Caption, t hen press ◄ / ► button to adjust..
30 Caption Display Press ▼ / ▲ button to se lect Caption Display , then press ◄ / ► button to s elect ON or OFF. Analog Caption Type Press ▼ / ▲ button to se lect Analog Capt ion Type, then press ◄ / ► button to se lect the type.
31 CC Opacity Press ▼ / ▲ button to select CC Opacity , then pr ess ◄ / ► butto n to select the Opacit y. Text Color Press ▼ / ▲ button to select Text Color , then press ◄ / ► button to se lect the color. CC Background Opacity Press ▼ / ▲ button to select CC Background Opacity, then press ◄ / ► button to select the Opacit y.
32 OTHERS MENU Blue Back Press ▼ / ▲ button to select Blue Backgroun d, then press ENTER butt on to select when there is no signal, whethe r set the backgroun d in blue or not. No Signal Power Off Press ▼ / ▲ button t o select No Signal Power Off, then press EN TER button to s elect it On or Off.
33 How do I Clean the TV? IMPOR T ANT 1. The power cable has to be removed fro m the socket before cleaning the TV . 2. Do not use volatile solvent (alcohol, rosin, and toluene) to clean the TV . These types of chemicals m ight dama ge the housing and the LED glass.
34 Troubleshooting Pro blems Solutions NO PICT URE Connect power cord correctly . T u rn on power . Connect video cable correctl y . Select the input signal source with proper cable connection with the source button. ABNORMA L COLORS Match the colors on the cables to the ports off the back of the television.
35 TV CHAN NELS ARE BLOCKED Check your auto lock function’ s settings inside the OS D. Y ou may have locked up som e channels but forgo t about them. UN IVERS AL REMOTE CODE Th is TV follows NEC’ s universal remote code. Plea se check your hand book for NEC’ s codes then apply the m .
36 SW ITCHING A CHANNEL OR SOURCE CHANGES THE VOLUME Different channels and inputs will sometimes have th is ef fect because the channel signal’ s own volume is already loud. There is no way remove this completely . The TV has an AUTO VOLUME LEVEL function that can combat this type of effect.
7 3 Display panel Item Illustration A c t i v e A r e a / S c r e e n S i z e Diagonal 39 inches 1 n e e r c s e d i W o i t a R t c e p s A 6:9 P i x e l P it c h 0.
8 3 So un d M od e Dynamic/Standard/Soft/User s e Y l o r t n o C e m u l o V o t u A e c n a l a B / e l b e r T / s s a B e n o T ) x a o c ( s e Y t u O L A I X A O C Spe a ke rs 6 watt per ch anne.
39 FCC Compliance Statement This device comp lies with Part 15 of the FCC Rules. Operation is subject to the following conditions: This device may not cause harmful interference This device must accept any interference rec e ived, including interference that my cause undesired operation.
An important point after buying a device RCA RLDED3950A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought RCA RLDED3950A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data RCA RLDED3950A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, RCA RLDED3950A you will learn all the available features of the product, as well as information on its operation. The information that you get RCA RLDED3950A will certainly help you make a decision on the purchase.
If you already are a holder of RCA RLDED3950A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime RCA RLDED3950A.
However, one of the most important roles played by the user manual is to help in solving problems with RCA RLDED3950A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device RCA RLDED3950A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
