Instruction/ maintenance manual of the product RHP100 Raypak
Go to page of 19
Raypak ® RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL This manual should be maint ained in legible condition and kept adjacent to the heat pump or in a safe place for future use.
i PRODUCT SAFETY SIGNS AND LABE LS This manual, as well as the pool/spa heat pum p itself, contains ANSI-approved product safety signs and labels. Please read these signs and labe ls, as they convey important safety information about hazards that may be potentially present in and around the heat pump.
ii RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I. Installation . . . . . .
1 Intr oduction This pool/sp a heat pump is an electromechanical m achine that incorporates a pressurized refrigerant gas in a sealed system. ONL Y trained and qualified service personnel should attem pt to install or servic e this equipment.
2 • Each side of the unit must be lo cated at least 1 ft fr om walls, pipes, or other obstructions for unrestricted air intake and service access. Do not inst all the unit within 3 f t of fossil fuel burning heaters.
3 III. W ater Connections The heat pump inlet and outlet connection s are NOT interchangeable. They must be connected as inst ructed below . 1. Connect the heat pump in the return water li ne between the pool filt er and the pool. See page 10, Plumbing Diagrams.
4 Indicator Lamps : There are 6 indicator lamps located on the unit control panel: • Power (amber lamp): When lit, indicates power is applied to the unit. NOTE: The heat pump will not run whe n the Remote position is selected and there is no remote control system attached.
5 NOTE: The heat pump wi ll be OFF when the Remote position is selected on th e Pool/Sp a selector switch and there is no remote con trol system att ached. 4.Allow the heat pump to op erate for a few minutes to stabilize operating pressure s and to allow various component temperatures to normalize.
6 VIII. Summer Shutdown If you do not plan to use the pool heat pump duri ng the summer months, secure and protect it as follows: 1. From the control panel, tu rn the contr ol switch to Remote (OFF). 2. T urn the heat pump circuit break er or disconnect switch to OFF .
7 2. B. Cabinet Care (optional) - The cabinet is designed for outdoor use and require s little care. However , you can clean it if you wish. 1. 2. W ash the cabinet with soap and water .
8 operation. After the desired temper ature is reached, return the system to normal operation of 8-10 hours per day . • Is airflow through the unit being obstructed? Restri ctions such as shrubbe ry , tall grass, dirty coils, or any other obstruction to airflow will reduce performance.
9 POWER SUPPL Y • V erify that all circ uit breakers are reset and working properly . •I f t h e Power lamp on the control pane l still does not light, cont act the installing dealer , since it may be a power probl em requiring an electrician. WAT E R F L O W • V erify that the filter is clean to provide good flow .
10 Plumbing Diagrams For systems with p umps of less than 2 HP (under 80 gpm) , no external bypass is required. Connections are 2 -inch pipe slip. Plumb the heat pump after the filter and before any chlorinators.
11 Heat Pump Schematic 12 34 A B C D 4 3 2 1 D C B A Title Number Revision Size A Date: 27-Jan-2003 Sheet of File: C:Pool FactPoofactPoofact.ddb Drawn By: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 .
12 Contr ol Panel Assembly Replacement Parts List 12 4 7 13 11 10 16 11 9 15 2 5 8 14 3 6 1 ITEM QTY DESCRIPTION PART No. 1 1 Control Panel 83-10002 2 1 Contactor Compressor 54-10002 3 1 Fan Relay 50-.
13 Contr ol Panel Cover Assemb ly Replacement Parts List 1 4 4 4 7 6 7 6 8 8 5 Front ITEM QTY DESCRIPTION PART No. 1 1 Control Panel Cover 81-30152 2 2 POT 50-10004 3 1 Switch Type A403 50-10005 4 3 K.
14 Heat Pump Assembly Re placement Parts List - RHP 100 11 15 13 12 5 9 18 2 7 7 7 6 8 1 4 10 3 17 14 9 19 RHP 100 16 0207 *See assembly drawing in this manual ITE M QT Y DESCRIPTION PART No.
15 Heat Pump Assembly Re placement Parts List - RHP 1 15 11 15 13 12 5 9 2 9 16 7 7 18 14 6 7 3 17 19 4 10 1 8 RHP 115 *See assembly drawing in this manual ITEM QTY DESCRIPTION PART No.
16 11 12 15 13 18 9 2 16 9 7 7 7 6 8 1 4 3 17 14 10 19 5 *See assembly drawing in this manual RHP 160 ITE M QTY DESCRIPTION PART No. 1 1 Assembly Base 8 1- 20 14 0 2 1 E vaporator Coil 40-10003 3 1 Ac.
An important point after buying a device Raypak RHP100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Raypak RHP100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Raypak RHP100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Raypak RHP100 you will learn all the available features of the product, as well as information on its operation. The information that you get Raypak RHP100 will certainly help you make a decision on the purchase.
If you already are a holder of Raypak RHP100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Raypak RHP100.
However, one of the most important roles played by the user manual is to help in solving problems with Raypak RHP100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Raypak RHP100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
