Instruction/ maintenance manual of the product DCA Series QSC
Go to page of 16
1 Cinema Accessories for DCA Series amplifiers USER MANUAL ▼ ▼ ▼ ▼ ▼ XC-3 Two-way crossover with delay ▼ ▼ ▼ ▼ ▼ LF-3 Low-frequency filter with delay ▼ ▼ ▼ ▼ ▼ SF-3 Subwoofer filter *TD-000079-00* TD-000079-00 rev.
2 ©Copyright 1998, 2002 QSC Audio Products, Inc. All rights reserved. “QSC , ” “DCA , ” “DataPort , ” and the QSC logo are registered trademarks of QSC Audio Products, Inc.
3 TABLE OF CONTENTS INTRODUCTION Introduction and d escription of e ach m odel.................................4 CONFIGURING THE ACCESSORIES General c onfiguration i nformation, all m odels...............................5 XC-3 Setting u p the XC-3....
4 INTRODUCTION & DESCRIPTION OF EACH MODEL XC-3 This accessory is a two-way crossover, with the low frequency band fed to channel 1 of the amplifier and the high frequencies t o channel 2. An all-pass filter on the low frequency band delays the audio signal, permitting time alignment of a cone driver with a high-frequency horn.
5 CONFIGURING THE ACCESSORIES Configurable functions of the three accessory models Configure each accessory before you mount it to the ampli- fier. If an accessory is already mounted to an amplifier, always turn the amplifier off before changing switch set- tings, changing input or output connections, or detaching the accessory.
6 XC-3 Setting u p the XC-3 Setting up the XC-3 requires setting the DIP switches and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #2, #9, and #10 must be set to the ON position (default settings for the XC-3). The flowchart below takes you through all the steps necessary before mounting the accessory to the amp.
7 Use these tables to determine the correct resistor values for the crossover frequencies and delays you need. The shaded values are for the high-pass frequency (f HP ) of the XC-3. XC-3 Setting u p the XC-3 Effects of high frequency boost on frequency response (crossover frequency = 500 Hz).
8 Setup flowchart for the LF-3 Setting up the LF-3 requires setting the DIP switches and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #2 and #4 through #9 must be set to OFF, and switch #3 set to ON (factory default for proper operation).
9 LF-3 Setting Up the LF-3 LF-3 Factory-installed SIPs LF-3 Factory Switch Settings LF-3 Recommended Amplifier Settings f xo 350 Hz, both channels (18 k Ω SIP resistor installed in J6 and J8) Delay 1.
10 Setting up the SF-3 SF-3 Setting u p the SF-3 Setting up the SF-3 requires setting the DIP switches, and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #1 through #6 and #10 must be set to OFF (factory default for proper operation).
11 SF-3 Factory-installed SIPs fHP= 30 Hz (27 k Ω SIP resistor in J2) fLP= 250 Hz (22 k Ω SIP resistor in J6) SF-3 Factory Switch Settings Switches 1 through 6 and Switch 10 OFF: Default setting f.
12 An accessory may be mounted with the amplifier either in or out of the rack, even if the amp is installed with rear rack ears. MOUNTING- All Models Mounting the Accessories 1. Turn off the amplifier before installing the accessory. 2. Make sure the SIP resistor networks are installed properly and no SIP sockets are empty.
13 Setting up the DCA Accessories in the Cinema Sound System If you are unable to obtain a satisfactory frequency response or SPL on a channel, carefully check the wiring and connections. Some likely causes are reversed speaker polarity on one or more drivers, loose or broken wiring or connections, or blown or damaged speaker drivers.
14 Cleaning The faceplate and chassis can be cleaned with a soft cloth and nonabrasive, noncorrosive, mild cleaning solution. Products like Simple Green and Windex work well. Do not use powders or scrubbing pads of any type as they are usually abrasive and will permanently damage the finish of your cinema accessory.
15 WORLD WIDE WEB: http://www.qscaudio.com FACSIMILE (FAX) NUMBERS: Sales & Marketing FAX +1 (714) 754-6174 Technical Services FAX +1 (714) 754-6173 TELEPHONE NUMBERS: Main Number +1 (714) 754-6175 Sales Direct Line +1 (714) 957-7100 or (800) 854-4079 toll free (U.
16 © Copyright 1998, 2002 QSC Audio Products, Inc. All rights reserved. “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office.
An important point after buying a device QSC DCA Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought QSC DCA Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data QSC DCA Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, QSC DCA Series you will learn all the available features of the product, as well as information on its operation. The information that you get QSC DCA Series will certainly help you make a decision on the purchase.
If you already are a holder of QSC DCA Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime QSC DCA Series.
However, one of the most important roles played by the user manual is to help in solving problems with QSC DCA Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device QSC DCA Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
