Instruction/ maintenance manual of the product PLMR440PA PYLE Audio
Go to page of 12
PYLE® HYDRA PLMR440PA Marine Public Address System Controller Remote Control Included OWNER'S MANUAL.
Congratulations on your purchase of a PYLE PLMR440PA Marine Public Address System Controller. It has been designed, engineered and manufactured to bring you the highest level of performance and quality, and will afford you years of listening pleasure.
Introduction An important member of the PYLE marine MOSFET amplifier series, we are pleased to introduce the unique PLMR440PA, a powerful amplifier with public address capabilities. This PYLE marine models features both high pass and low pass crossovers.
Installation precautions Before you drill or cut any holes, investigate your vessel's layout very carefully. Take special care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring. Never operate the amplifier when it is unmounted.
Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance.
High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems.
High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems.
Microphone Input Wiring If you wish to use the public address feature in the PLMR440PA, all you need to do is to connect the custom microphone included with the amp. When you press the button on the microphone, it automatically cuts off the input to Channels 1-4 from your audio source and presents the microphone signal to the amplifier.
Power and Speaker Wiring 4 Channel Mode Four Channel Mode RED """'" CONNECnONS Chassis ground point PYLE" H""RA PLMR440PA.
Power and Speaker Wiring Bridged Mode Bridged Mode RED P<ME. CONNEcnONS Chassis ground point PYLE" HYDRA PLMR440M _"='m"=~ER ID REMOlE lURN'()N ORANGE IenTinai of head un~ FUSE (provided) {} D D I Battery I .
Speaker Wiring Tri-Mode Tir-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. To set the amplifier to run in this mode, put the crossover switch In the FULL posifion.
Troubleshooting Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. Amplifier will not power up. Check for good ground connection. Check that remote DC terminal has at least 13.
An important point after buying a device PYLE Audio PLMR440PA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought PYLE Audio PLMR440PA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data PYLE Audio PLMR440PA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, PYLE Audio PLMR440PA you will learn all the available features of the product, as well as information on its operation. The information that you get PYLE Audio PLMR440PA will certainly help you make a decision on the purchase.
If you already are a holder of PYLE Audio PLMR440PA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime PYLE Audio PLMR440PA.
However, one of the most important roles played by the user manual is to help in solving problems with PYLE Audio PLMR440PA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device PYLE Audio PLMR440PA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
