Instruction/ maintenance manual of the product PLA1200 PYLE Audio
Go to page of 26
.
congratulations... on your purchase of a Pyle Chopper Series amplifier. This amplifier extends the Pyle tradition into a totally new series of amps, designed from the ground up to deliver the power, performance and flexibility the modern car audio enthusiast demands.
2/4 channel input connections PLA-4120 14 PLA-2230/PLA-2260 general features 2-3 speaker connections PLA-4120 system wiring PLA-1200 system wiring speaker connections 17 table of contents features and.
· Mono Block Subwoofer Amplifier · 1 Ohm Stable · MOSFET Power Supply · PWM (Pulse-Width-Modulation) System · Glass Epoxy PCB · Gold Plated RCA Inputs for Line Input & Bypass Output. · Gold Plated T erminals for Speaker Output and Power Input.
· 2000 Watts x 2 Output · 4000 Watts x 1 Bridged Output · Variable Hi/Lo Electronic Crossover Network · Variable Input Level (Gain) Control · Sub Sonic Filter · Variable Bass Boost · Thermal / .
4 frequency response output power @ 14.4v DC, 50Hz RMS Power at @ 4 Ohms RMS Power at @ 2 Ohms RMS Power at @ 1.3 Ohms Maximum Power Output 20 0 W MONO 3 50W MONO 60 0 W MONO 19 00W MONO 20 Hz-250 Hz ( - 3dB) input impedance 10K Ohms Stiffly regulated PWM power supplies.
PLA-1200 5 features and controls MONO BLOCK AMPLIFIER PLA-1200.
When used with normal, full range system, set this switch to "FULL" . If you wish to use the internal crossover to power a driver or specific frequency range, use the "LPF"or "HPF" FOR the "LOWP ASS" OR HIGHP ASS" settings.
2 ch amp PLA-2230 • PLA-2260 PLA-2230 PLA-2260 7 features and controls.
frequency response output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms THD @ 4 Ohms RMS Power @ 2 Ohms THD @ 2 Ohms Maximum Power Output bridged Power at 4 Output input sensitivity low level inputs input impedance low level inputs This amp features gold-plated RCA type jacks for high impedance input.
PLA-4120 9 1 8dB 0dB HPF LPF FULL HPF LPF FULL 1 8dB 0dB BASS BOOST X - OVER BASS BOOST X - OVER CH 1 / 2 CH 3 / 4 features and controls 4 ch amp PLA-4120.
PLA- 2230 PLA- 2260 10 2 ch amp • PLA-2230 • PLA-2260 electrical connections.
PLA-4120 11 electrical connections 4 ch amp PLA-4120.
12 PLA- 2230 PLA-2260 stereo input connections 2 ch amp • PLA-2230 • PLA-2260.
13 PLA- 2230 PLA-2260 mono input connections 2 ch amp • PLA-2230 • PLA-2260.
PLA- 4120 14 4 ch amp PLA-4120 2/4 channel input connections.
4 CH floating ground connections PLA-4120 15 4 ch amp PLA-4120 high level input connections.
PLA- 4120 16 4 CH mono input connections using low level inputs 2 CH mono input connections using low level inputs 4 ch amp PLA-4120 mono input connections.
17 Stereo Output Mode PLA- 2230 PLA-2260 Bridged Mono Output Mode speaker connections 2 ch amp • PLA-2230 • PLA-2260.
PLA- 4120 18 4 CH Output Mode Bridged Dual Mono Output Mode speaker connections 4 ch amp PLA-4120.
PLA- 4120 19 2 CH Stereo Output Mode with Mono Bridged Subwoofer Output speaker connections 4 ch amp PLA-4120.
PLA - 1200 20 MONO BLOCK AMPLIFIER PLA-1200 system wiring.
21 mounting Y our new Pyle Chopper Series amplifier comes complete with all required mounting hardware. When determining a suitable location in your vehicle for the amp, please remember that it is a high-power electronic device capable of generating high heat.
22 The built-in protection circuitry in the Pyle Chopper Series amplifiers will disable the amplifier if it senses an input overload, a speaker short circuit, or extreme temperature conditions. When the protection circuit is activated by any of these conditions, the Protection LED will be illuminated.
23 STOP YES! NO! 2 -c hannel Amplifier (Operating in Stereo) 4 ohm 4 ohm Two 4-ohm speakers, wired in stereo, will present a 4-ohm load to each channel of the amplifier. Most two- channel amplifiers will work well in this configuration. Two 4-ohm speakers, wired in parallel to a bridged two-channel amplifier.
All Pyle products are carefully constructed and thoroughly tested before shipment. Products purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchase.
An important point after buying a device PYLE Audio PLA1200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought PYLE Audio PLA1200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data PYLE Audio PLA1200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, PYLE Audio PLA1200 you will learn all the available features of the product, as well as information on its operation. The information that you get PYLE Audio PLA1200 will certainly help you make a decision on the purchase.
If you already are a holder of PYLE Audio PLA1200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime PYLE Audio PLA1200.
However, one of the most important roles played by the user manual is to help in solving problems with PYLE Audio PLA1200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device PYLE Audio PLA1200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
