Instruction/ maintenance manual of the product 352VS PYLE Audio
Go to page of 17
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage.
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm.
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6 ADDITIONAL SPECIFIC SAFETY RULES SAVE THESE INSTRUCTIONS! 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ...................
Extreme care should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause irreversible brain and nervous system damage. Young and unborn children are particularly vulnerable.
9 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section.
10 OPERA TION NOTE: This tool is shipped completely assembled. No assembly time or tools are required. ASSEMBL Y 1. Place the sander on its left side. 2 . Pull the lever (A) Fig. 1 out toward the front of the machine to retract the idler pulley (B) and release the tension on the abrasive belt.
TRACKING THE ABRASIVE BEL T To prevent excessive wear on both the sander and belt, NEVER allow the abrasive belt to rub on the sander frame. To make sure that the belt is tracking correctly, do the following: Make sure that the trigger switch is “ OFF” before con- necting the tool to the power source.
12 SELECTING AN ABRASIVE BEL T The principle abrasive materials used on belts for machine sanding are aluminum oxide and silicon carbide. Aluminum oxide is the softer of the two, but is tougher and more suited for woods and soft (non-ferrous) metals. Silicon carbide is extremely hard and is best suited for surfacing stone, marble, and glass.
13 Overlap the strokes and cover the entire surface, working from both sides of the board (angle left and then angle right.) Smooth the surface by guiding the sander back and forth with the grain. Change the belt to a medium grit and follow the same procedure.
14 BE CAREFUL when sanding at the end of a board. Keep the tool level and flat on the work surface. Don’t let the front of the tool drop. (Fig. 6). If this happens, it will round the edge. The model 352VS sander works very fast and can do a thorough job in a fraction of the time required by hand sanding.
15 REPLACEMENT P ARTS When servicing use only identical replacement parts. For a service parts list or to learn more about Porter-Cable visit our website at www.porter-cable.com SERVICE AND REP AIRS All quality tools will eventually require servicing, or replacement of parts due to wear from normal use.
16 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.
An important point after buying a device PYLE Audio 352VS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought PYLE Audio 352VS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data PYLE Audio 352VS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, PYLE Audio 352VS you will learn all the available features of the product, as well as information on its operation. The information that you get PYLE Audio 352VS will certainly help you make a decision on the purchase.
If you already are a holder of PYLE Audio 352VS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime PYLE Audio 352VS.
However, one of the most important roles played by the user manual is to help in solving problems with PYLE Audio 352VS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device PYLE Audio 352VS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
