EN
Proview logo
Official user manual

Proview CRT Monitor (786PF)

45 pages·2.5 MB·Computer Monitor·PDF·EN
Proview CRT Monitor (786PF)
Table of Contents 80 sections 786PF Service Manual · PROVIEW ELECTRONICS CO.,LTD · A. IMPORTANT SAFETY INSTRUCTION · B. SPECIFICATIONS · … ShowHide
Page 1 of the Proview CRT Monitor (786PF) user manual — PROVIEW ELECTRONICS CO.,LTD
Page 1 · click to enlarge
Page 1
Proview CRT Monitor (786PF) — 786PF Service Manual diagram (page 1)
Fig. 1 · 786PF Service Manual

786PF Service Manual

PROVIEW ELECTRONICS CO.,LTD

6F,No.1,Pau-Sheng Road,Yung-Ho City,Taipei 234,Taiwan Tel : (886-2) 2231-6789 , Fax :(886-2) 2231-5678

Page 2 of the Proview CRT Monitor (786PF) user manual — 786PF Service Manual
Page 2 · click to enlarge
Page 2
Page 2 of the Proview CRT Monitor (786PF) user manual — 786PF Service Manual
Page 3 of the Proview CRT Monitor (786PF) user manual — A. IMPORTANT SAFETY INSTRUCTION
Page 3 · click to enlarge
Page 3

To prevent from fire or shock hazard,do not expose monitor to any rain or any form of water.High voltage is inside the monitor so please do not remove the back cover of the cabinet if you are not a qualified monitor engineer. Contact the local dealer or the nearest MAG branch office if you need help.

A. IMPORTANT SAFETY INSTRUCTION

Prior to using this service manual,please ensure that you have carefully followed all the procedures outlined in the user's manual for this product. 1. Read all of these instructions. 2. Save these instructions. 3. Follow all warnings and instructions a marked on the product. 4. Unplug this product from the wall outlet before cleaning.Do not use liquid cleaners or aerosol cleaners, use a damp cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart,stand or tablle.The product may fall,causing serious damage to the product. 7. Slots and openings in the cabinet and the back or bottom are provided for ventilation,to ensure reliable operation of the product and to protect it from overheating,those openings must not be blocked or covered.The openings should never be blocked by placing the product on a bed,sofa, rug, or other similar surface.This product should not be placed in a built-in installation less proper ventilation is provided. 8. This products should be operated from the type of power source indicated on the marketin label. If you are not sure of the type of power available, consult your dealer or local power company 9. This product is equipped with a 3-wire grounding type plug,a plug having a third (grounding) pin.This plug will only fit into a grounding-type power outlet.This is a safety feature,if you are unable to insert the plug into the outlet,contact your electrician to replace your obsolete outlet.Do not defeat the purpose of the grounding-type plug. 10. Do not allow anything to rest on the power cord.Do not locate this product where persons will walk on the cord. 11. If an extension cord is used with this product,make sure that the total of the ampere ratings on the product plugged into the extension cord to the waplugged into outlet does not exceed 15 ampere. 12. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.Never spill liquid of any kind on the product. 13. Do not attempt to service this product yourself,as opening or removing covers may expose you to dangerous voltage points or other risks.Refer all servicing to service personnel. 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions.

a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally,when the operating instructions are followed.Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extension work by a qualified technician to restore the product to normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance,indicating a need for service. For Model 786PF WARNING : This product included critical components which are essential for X-Radiation safety.

Page 4 of the Proview CRT Monitor (786PF) user manual — 786PF
Page 4 · click to enlarge
Page 4

See service manual for proper replacement.Maximum 2nd anode voltage must not exceed 30KV at any operating conditions. To measure 2nd voltage use high impedance meter connect (-) chassis, use a high voltage lead from (+) to 2nd anode.

VR501,VR601 has been sealed against improper replacement or defeating the control. Instructions for proper replacement of such sealed controls should also be provided in the

service information.

B. SPECIFICATIONS

786PF

Page 5 of the Proview CRT Monitor (786PF) user manual — C. TIMING CHART
Page 5 · click to enlarge
Page 5
1. Screen 17“ 0.25mm dot pitch,Pure Flat Square Tube,90°deflection, Anti-glare,Anti-static,Anti-reflection. 2. Visible Image Area 16.0 inch 3. Active Display Area 310mm (H) × 230mm (V) 4. Synchronization Range Horizontal Vertical
30. 86 KHz 50 – 160 Hz 5. Power Source 100 – 240 Vac , 60/50 Hz 6. Power Consumption 120W (max.) 7. Input Signal Video Sync.

Analog R.G.B. , 0.7Vp-p / 75 Ohm TTL level,positive or negative polarity 8. Connection Type 15 Pin D Type 9. Resolution 1600 × 1200 pixels 10. Color Temperature 9300ºK / 6500ºK 11. Dimension (W×H×D) 410 × 418 × 423 (mm) 12. Monitor Weight 16.8Kg (37.0Lbs) 13. Base Operation Tilt Swivel

- 5º / + 15º - 45º / + 45º 14. Power Saving ON

< 120W < 5W 15. Signal Connector Pin Assignment Pin No. 1. Red 2. Green 3. Blue 4. Ground 5. Self Test

OFF

11. Ground 12. SDA 13. Horizontal Sync. 14. Vertical Sync. 15. SCL
6. Red Ground 7. Green Ground 8. Blue Ground 9. Not Connected 10. Sync. Ground

C. TIMING CHART

APeriod B : Active
Video CSync Width
Page 6 of the Proview CRT Monitor (786PF) user manual — D. CONTROL LOCATION
Page 6 · click to enlarge
Page 6
DBack Porch D B E E : Front porch

Sync. C A

Preset ModesVGA 640 × 480VGA 720 × 400VESA 800 × 600VESA 640 × 480XGA 1024 × 768SIEMENS 640 × 480VESA 800 × 600VESA 1024 × 768SIEMENS 800 × 600VESA 1024 × 768VESA 1280 × 1024 Dot Rate (MHz)25.17528.32240.00036.00065.00040.50056.2578.75067.594.5135 F.H (KHz)31.46931.46937.87943.26948.36350.60053.67460.02363.9268.67779.976 APeriod (uS)31.77831.77826.40023.11120.67719.75218.63116.66015.64414.56112.504 BActive (uS)25.42225.42220.00017.77815.75415.80214.22213.00311.85210.8369.481 CSync (uS)3.8133.8133.2001.5562.0921.581.1381.2190.9481.0161.067 D-Back Porch (uS)1.9071.9072.2002.2222.4621.9752.7022.2352.3702.2011.837 E-Front Porch (uS)0.3180.3181.0001.5560.3690.3950.5690.2030.4740.5080.119 F . V (Hz)59.94170.08760.31785.060.004100.185.06175.029100.084.99775.025 APeriod (Ms)16.68314.26816.57911.76416.6669.99511.75613.3289.99711.76513.329 BActive (mS)15.25312.71115.84011.09315.8809.48111.17912.7959.38711.18312.804 CSync (mS)0.0640.0640.1060.0690.1240.0590.0560.0500.0470.0440.038 D-Back Porch (mS)1.0491.1120.6070.5780.6000.4350.5030.4660.5480.5240.475 E-Front Porch (mS)0.2540.2220.0260.0230.0620.020.0190.0170.0160.0150.013 H/V SYNC-. -- . +-. -+ . +-. --. -+ . ++ . ++ . ++ . ++ . + InterlacedNONNONNONNONNONNONNONNONNONNONNON

D. CONTROL LOCATION

Font control panel

Page 7 of the Proview CRT Monitor (786PF) user manual — E. ADJUSTMENT CONTROL LOCATION
Page 7 · click to enlarge
Page 7

a. Power Switch b. Power Indicator c.Encoder d. Enhance Key

E. ADJUSTMENT CONTROL LOCATION

Page 8 of the Proview CRT Monitor (786PF) user manual — ITEM
Page 8 · click to enlarge
Page 8

VR601

VR501

L705 T501

Q703

C504 Q504

FBT

F501

F. ADJUSTMENT PROCEDURE

﹟Test Meter ﹡Test Point ﹫Pattern

ITEM

Program Menu.

Adjusting Value · Operation

Page 9 of the Proview CRT Monitor (786PF) user manual — VR601
Page 9 · click to enlarge
Page 9
﹟Digital Voltmeter ﹡D510 Negative ﹫Crosshatch Pattern (31.5KHz,640x480)1. Make the adjustment to the value shown at right by turning the VR501 on the main PCB.15.5V ±0.2V BHigh Voltage Adjust﹟Digital Voltmeter ﹟High Voltage Probe ﹡Anode Cap-GND ﹫Crosshatch Pattern (31.5KHz,640x480)1. Turn the power switch of the monitor OFF. 2. Connect high voltage probe to Anode Cap and GND. 3. Turn the power switch of the monitor ON. (15 minutes) 4. Make the adjustment to the value shown at right by turning the VR601 on the main PCB.26.0KV CPreset Adjust﹫Crosshatch (31.5KHz,640x480)1. Turn the power switch of the monitor OFF. 2. Hold encorder key,then turn the power switch of the monitor ON. 3. Turn encorder key,make sure into preset picture, if not ,please return 1-2. 4. Please following the procedure of selection and adjusting an item using the OSD system as below steps for main function adjusent. Step 1 : Press and relese the OSD control knob to activate the OSD menu. Step 2 : Turn the knob to highlight the desired option of OSD icon. Step 3 : Press and release the knob again to access the option. The color of the inner area of the OSD will changed from blue to green. Step 4 : To make your adjustment,turn the knob Clockwise to increase or countclockwise to decrease the setting. Step 5 : Press and release the knob again to store the change.the color of the inner area will go back to blue.You can select EXIT icon and press the knob the exit the OSD menu.Contrast : MAX. Brightness MAX. H-Size : 310mm V-Size : 230mm H-Posi. : Center V-Posi : Center ITEM Program Menu.﹟Test Meter ﹡Test Point ﹫PatternOperationAdjusting Value
Page 10 of the Proview CRT Monitor (786PF) user manual — ITEM
Page 10 · click to enlarge
Page 10
DBackground White Balance Adjust﹟Color Analyzer ﹫R.G.B off (68KHz,1024x768)1. Set the contrast to MAX.,Brightness to Y=0.7 set color is 9300°K using the OSD. 2. Set the OSD to COLOR of sub menu and press knob. 3. Make the adjustment R.G.B BIAS low light to the value shown at right by using encorder.Y = 0.7 ±0.1FL x = 0.283 ±0.01 y = 0.297 ±0.01 EWhite Balance Adjust﹟Color Analyzer ﹟Oscilloscope ﹡Cathode G ﹫3” block (68KHz,1024x768)1. Move the OSD to the R.G.B. DRIVE. 2. Move the OSD to the G DRIVE and make the adjustment to the value shown at right by using encorder. 3. Move the OSD to the R,B-DRIVE and make the Adjustment to the value shown at right by using Encorder.37VP-P x = 0.283 ±0.01 y = 0.297 ±0.01 FABL Adjust﹟Color Analyzer ﹫Full White (64KHz,1280x1024)1. Set the contrast to MAX.,Brightness to MAX. 2. Make the adjustment to the value shown at right by adjustment ABL on the OSD menu.Y = 33FL GOther Function Seting﹫Full White (64KHz,1280x1024)1. Set the FREQ. to 87 2. Set the OSD to MAG 3. Set the BURN to Disable 4. Set the TIME to 15 5. Set the DEFO to TDA9113/9112 HDynamic Focus Adjust﹟Oscilloscope ﹡FBT Pin14 ﹫Full White (31.5KHz,640x480)1. Set the contrast to MAX.,and adjustment Brightness to the raster just appear. 2. Make the adjustment to the value shown at right by adjust the VF on the OSD menu. 3. Make the check to the value shown at right by adjust the HF on the OSD menu.VF : 140 ±10VP-P HF : 430 ±10VP-P IPurity Adjust﹫Magenta color (31.5KHz,640x480)1. Adjust the purity magnet is in magneta color. 2. Turning two overlapping pawels in opposite directions. 3. Move them until they are at the same angle, 9 o’clock and 3 o’clock respectively.

﹟Test Meter ﹡Test Point ﹫Pattern

ITEM

Program Menu.

Adjusting Value · Operation

Page 11 of the Proview CRT Monitor (786PF) user manual — J
Page 11 · click to enlarge
Page 11

J

﹫Magenta color (31.5KHz,640x480)

1. Open the two pawels of the 4 pole magnets to allow the red and blue vertical lines to unite. 2. Open and rotate the two pawels at a contrast angle so that the red and blue horizontal lines can unite. 3. If the vertical lines deviates,open the two powals at the deviation position and make a monitor adjustment by changing its angle. 4. Display white crosshatch pattern. 5. Make the red and blue vertical lines at the center unite with the green by opening the two 6 pole pawels. 6. Rotate the two pawels at contrast angle so that the red and blue horizontal lines can unite with the green.

7. If the vertical lines deviate,change the angle of Pawels from the deviation position.

Static Convergence Adjust

Page 12 of the Proview CRT Monitor (786PF) user manual — VR601
Page 12 · click to enlarge
Page 12
Proview CRT Monitor (786PF) — VR601 diagram (page 12)
Fig. 2
Page 13 of the Proview CRT Monitor (786PF) user manual — VR601
Page 13 · click to enlarge
Page 13
Proview CRT Monitor (786PF) — VR601 diagram (page 13)
Fig. 3
Page 14 of the Proview CRT Monitor (786PF) user manual — G. BLOCK DIAGRAM
Page 14 · click to enlarge
Page 14

G. BLOCK DIAGRAM

Proview CRT Monitor (786PF) — G. BLOCK DIAGRAM diagram (page 14)
Fig. 4
Page 15 of the Proview CRT Monitor (786PF) user manual — G. BLOCK DIAGRAM
Page 15 · click to enlarge
Page 15
Proview CRT Monitor (786PF) — G. BLOCK DIAGRAM diagram (page 15)
Fig. 5
Page 16 of the Proview CRT Monitor (786PF) user manual — G. BLOCK DIAGRAM
Page 16 · click to enlarge
Page 16
Proview CRT Monitor (786PF) — G. BLOCK DIAGRAM diagram (page 16)
Fig. 6
Page 17 of the Proview CRT Monitor (786PF) user manual — G. BLOCK DIAGRAM
Page 17 · click to enlarge
Page 17
Proview CRT Monitor (786PF) — G. BLOCK DIAGRAM diagram (page 17)
Fig. 7
Page 18 of the Proview CRT Monitor (786PF) user manual — G. BLOCK DIAGRAM
Page 18 · click to enlarge
Page 18
Proview CRT Monitor (786PF) — G. BLOCK DIAGRAM diagram (page 18)
Fig. 8
Page 19 of the Proview CRT Monitor (786PF) user manual — G. BLOCK DIAGRAM
Page 19 · click to enlarge
Page 19
Proview CRT Monitor (786PF) — G. BLOCK DIAGRAM diagram (page 19)
Fig. 9
Page 20 of the Proview CRT Monitor (786PF) user manual — T501 (7)
Page 20 · click to enlarge
Page 20

H. TROUBLE SHOOTING HINTS

BRIGHT HOR. LINE APPEAR ON THE SCREEN

NO POWER

T501(7) VOLTAGE

No No Yes No Yes

T501 (7)

CHECK F501,D514 , D515,D516, D517

AC120V IN 160V AC220V IN 294V AC230V IN 308V

160 V ?

IC501 (7)

CHECK IC501,R539, D505,ZD551

> 14 V ?

IC501(6)

CHECK

IC501,Q504

D510 (-)

CHECK

15.5V ?

D510,Q501,

Q508

CIRCUIT

SHORT

Show 4 more labels / short text on this page
No · 14Vp-p ? · Yes No · Yes
Page 21 of the Proview CRT Monitor (786PF) user manual — IC301 (2)
Page 21 · click to enlarge
Page 21

NO

RASTER

Yes No Yes No Yes No

IC301 (2)

CRT G1

CHECK Q710 (E)

IC901(4) -1.5V~-1.8V

CHECK

-20V~ -80V ? 12 V ?

-0.6V ?

15V LINE

CKT

IC301 (4)

CHECK

-12 V ?

-12V LINE

IC301 (1)

CHECK

0.7 V P-P ?

IC301 (5)

CHECK

48 V P-P ?

CHECK

CRT DY

No · IC901 Surrounding · Yes

Page 22 of the Proview CRT Monitor (786PF) user manual — HEATER
Page 22 · click to enlarge
Page 22

DEFLECTIVE

HOR. CKT

Yes Yes No No

HEATER

CHECK B+ VOLT

CHECK

CHECK

VOLT 6.3 V ?

Q711(B) < 0.7 V ?

IC901(24)

7.2 V ?

> 2.0 V ?

CRT EHT 26KV ?

CHECK

CHECK

CKT

CRT G2

CHECK

CHECK VIDEO CKT

600V ?

T701 FBT

CRT KR,KG,KB

VIDEO CKT

FAILURE

VOLTAGE

CHECK

CRT TUBE

Show 8 more labels / short text on this page
No No No · Yes Yes · No No · Yes · CHECK Deflection Horizontal · No · Yes No Yes · ?
Page 23 of the Proview CRT Monitor (786PF) user manual — SUSPEND ON/OFF OFF FLICKER
Page 23 · click to enlarge
Page 23
Proview CRT Monitor (786PF) — SUSPEND ON/OFF OFF FLICKER diagram (page 23)
Fig. 10

Fh T701(3) B+ 31.5KHz 63V 37KHz 77V 48KHz 93V 54KHz 104V 56KHz 111V 64KHz 127V 68KHz 139V 75KHz 153V 80KHz 166V 86KHz 181V

SUSPEND ON/OFF OFF FLICKER

Page 24 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 24 · click to enlarge
Page 24

NO ROTATION

P903

OK ?

IC901(20)

CHECK

PS 0 0 V ?

Q505 (C)

CHECK

7.0 V ?

Q505

CHECK Q511 (B)

CHECK

0 V ?

CHECK

Q511

Show 7 more labels / short text on this page
Yes · No · No · Yes · No Yes · No Yes · No
Page 25 of the Proview CRT Monitor (786PF) user manual — 39 V P-P ?
Page 25 · click to enlarge
Page 25

NO CHARACTERS

MISSING ONE

COLOR

CRT KG

NO CHECK

80V 0-P ?

RASTER

IC203 (3)

CHECK

CHECK

Yes No Yes No Yes

39 V P-P ?

IC203 15 E

V LIN

15 V ?

R979

CHECK

7 V ?

7V LINE

Q902 (B) Q903 (B) 1.5~13V ?

CHECK

Q902 Q903

Q904 (B)

CHECK

0~2.5V ?

CHECK

Q904

Example:Missing Green

Show 7 more labels / short text on this page
Yes · No · Yes · Rotation Coil · No · Q902 (c) · No Yes
Page 26 of the Proview CRT Monitor (786PF) user manual — CHECK
Page 26 · click to enlarge
Page 26

OSD DOES NOT

Yes No Yes No Yes No

WORK

IC201 (19)

IC201(24)

CHECK

OSD G

7V ?

5V 0-P ?

IC202 (3)

CHECK

5 V 0-P ?

M703

BLK ?

CHECK

(8) 12 V ?

CHECK

(10) 5 V ?

IC201 (7)

CHECK I/P

0.7V P-P ?

SIGNAL

CHECK

ExampleMissing Green

0.4 V ?

ConditionOSD on

Yes Yes No No

CHECK

Show 6 more labels / short text on this page
No · Yes · No Yes · (19) · (32) · Yes
Page 27 of the Proview CRT Monitor (786PF) user manual — IC202(6)
Page 27 · click to enlarge
Page 27

IC202(6)

CHECK

4.2V P-P ?

80V ?

CHECK

D203

I. REPLACEMENT PARTS LIST

786PF Spare Parts List REV:A Location. Parts Number Parts Description Q’ty

R631 210-100-0256 10 Ω 1/2W 1

R734 210-100-0256 10 Ω 1/2W 1

R762 210-100-0456 10 Ω 1/4W 1

R7A2 210-100-0856 10Ω 1/8W 1 R612,611,663,912,918,926,927,976 R977 210-101-0456 100Ω 1/4W 9

No Yes · No

Page 28 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 28 · click to enlarge
Page 28
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 28)
Fig. 11

R288,291,510,590, 606,615, 630, 651 R730,931,947 210-103-0856 10KΩ 1/8W 11

Page 29 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 29 · click to enlarge
Page 29
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 29)
Fig. 12

R712 210-4R7-0456 4.7Ω 1/4W 1 R202,232,262,551,726,729 L200,L230,L260 210-470-0856 47Ω 1/8W 9

Page 30 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 30 · click to enlarge
Page 30
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 30)
Fig. 13
Page 31 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 31 · click to enlarge
Page 31
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 31)
Fig. 14
Page 32 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 32 · click to enlarge
Page 32
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 32)
Fig. 15
Page 33 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 33 · click to enlarge
Page 33
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 33)
Fig. 16

C708,778 328-103-2260 0.01u 50V C.C 2 C271,291,293,295,202,232,262,2A1, C2A5,2A6,603,622,616,513,903,904, C 908,909,920,921,902A,902B,724

Page 34 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 34 · click to enlarge
Page 34
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 34)
Fig. 17

Q505 510-010-772SP HSB772S (TO – 92) 1 Q502,508,511,513,601,606,651,708 Q711,722,902,904,907 510-023-0945 2SC945P 13

Page 35 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 35 · click to enlarge
Page 35
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 35)
Fig. 18
Page 36 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 36 · click to enlarge
Page 36
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 36)
Fig. 19
Page 37 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 37 · click to enlarge
Page 37

MAIN BOARD (Soild Side)

Page 38 of the Proview CRT Monitor (786PF) user manual — K. SCHEMATIC DIAGRAM
Page 38 · click to enlarge
Page 38

K. SCHEMATIC DIAGRAM

Page 39 of the Proview CRT Monitor (786PF) user manual — MEMO
Page 39 · click to enlarge
Page 39

MEMO

Page 40 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 40 · click to enlarge
Page 40
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 40)
Fig. 20
Page 41 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 41 · click to enlarge
Page 41
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 41)
Fig. 21
Page 42 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 42 · click to enlarge
Page 42
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 42)
Fig. 22
Page 43 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 43 · click to enlarge
Page 43
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 43)
Fig. 23
Page 44 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 44 · click to enlarge
Page 44
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 44)
Fig. 24
Page 45 of the Proview CRT Monitor (786PF) user manual — NO ROTATION
Page 45 · click to enlarge
Page 45
Proview CRT Monitor (786PF) — NO ROTATION diagram (page 45)
Fig. 25

Ask about the Proview CRT Monitor (786PF)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Proview CRT Monitor (786PF)

Be the first to ask — other owners or our team will answer.

Original document

Proview CRT Monitor (786PF) manual PDF

45 pages·2.5 MB·Computer Monitor·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…