Instruction/ maintenance manual of the product HA1000 Profile
Go to page of 20
MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Manual HA1000 HA740 HA1040 HA600 HA400 HA700M HA1000M.
1 Serial # Model # I NTRODUCTION Congratulations on your purchase of a Baja state-of-the-art power amplifier. Your selection of a Baja car audio product indicates a true appreciation of fine musical reproduction.
2 S AFETY PRECAUTIONS battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST. The amplifier's built-in fuse will only protect the power amplifier and not the car's battery! The fuse value is based on the amplifiers rated power and how many amplifiers will be run off the same power wire.
3 Built-in Crossover The Baja amplifiers include a built-in variable **high and low pass crossovers. The crossover features a variable frequency selection of (80 Hz ~ 1.2k Hz) for precise high pass filter and (50 Hz ~ 250 Hz) for low pass filter. ** HA1000, HA700M and HA1000M models only have a 50 Hz ~ 250 Hz low pass filter.
Tri-Mode Capable (Excluding HA700M & HA1000M models) If so desired the amplifier may be run in stereo and mono at the same time. For example, this feature would allow you to run a pair of mids and tweeters in stereo and a subwoofer in mono. 4 Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output.
5 Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operation, correct the problem and turn the head unit off, then back on.
6 P OWER CONNECTIONS Connect the B+ terminal of the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box.
7 M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation.
8 TWO CHANNEL SIGNAL CONNECTIONS FOUR CHANNEL SIGNAL CONNECTIONS (RADIO WITH FRONT AND REAR OUTPUTS) FRONT REAR Connect 2 sets of RCA "Y" adaptors to split the two RCA's from the radio .
will allow you to connect directly to the speaker output of the radio, without the need of an external adapter. GND 9 connect the amplifier to a factory radio without low-level RCA outputs.
10 Make the speaker connections using speaker wire that is at least 14 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-).
11 S PEAKER CONNECTIONS (BRIDGED) Two and four channel amplifiers are capable of being bridged ** into a mono configuration. This feature allows you the flexibility of using the amplifier to drive a subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output.
12 NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D Left Mid / Tweeter 4 Ohm (2 Ohm Minimum) Mono Woofer 8 Ohm (4 Ohm Minimum) Right Mid / Tweeter 4 Ohm (2 Ohm Minimum) ¹ F 100 ¹ F 100 CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s).
13 Select the crossover type on the amplifier's side panel. ( High-pass is selected in this example for tweeters/midranges ) (Please note: If you intend to use the amplifier in the Tri-mode confi.
14 control until the system gets loud but before the point of distortion. It is very important S ETTING THE GAIN The gain control has been included to allow adjustment to properly To properly set the gain, start by setting the gain to its minimum position and turn the main radio volume up to 3/4 of maximum volume control.
15 T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself.
16 S PECIFICATIONS HA400 HA600 2 x 130W 2 x 65W 2 x 200W 2 x 100W 1 x 200W Yes <0.07% 20Hz ~ 30kHz >100dB 83dB Yes 200mV ~ 7V 20K Ohms 42 Ohms 2 ~ 8 Ohms 4 ~ 8 Ohms HP / FULL / LP 50Hz ~ 250Hz 80Hz ~ 1.2kHz 0dB ~ 12dB - - - - - 320 20A 2 1/4 " x 9 11/16 " x 9 1/16 " 2 x 200W 2 x 100W 2 x 300W 2 x 150W 1 x 300W Yes <0.
S PECIFICATIONS Max Power Output@4 Ohm RMS Power Output@4 Ohm Max Power Output@2 Ohm RMS Power Output@2 Ohm MOSFET Power Supply THD@RMS Power Frequency Response Signal To Noise Stereo Separation Pre-A.
Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser.
15060 SHOEMAKER AVE. By PROFILE CONSUMER ELECTRONICS, INC. SANTA FE SPRINGS, CA 90670 TEL: (562) 404-9393 FAX: (562) 404-9433 www.profileusa.com 15060 SHOEMAKER AVE. SANTA FE SPRINGS, CA 90670 In the unlikely event of product failure, the following procedures 2) The unit must have no physical damage.
An important point after buying a device Profile HA1000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Profile HA1000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Profile HA1000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Profile HA1000 you will learn all the available features of the product, as well as information on its operation. The information that you get Profile HA1000 will certainly help you make a decision on the purchase.
If you already are a holder of Profile HA1000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Profile HA1000.
However, one of the most important roles played by the user manual is to help in solving problems with Profile HA1000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Profile HA1000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
