Instruction/ maintenance manual of the product TS-428 Princeton
Go to page of 10
15 Discovery Way, Acton, MA 01720 Phone: (978)263-3584, Fax: (978)263-5086 Web Site: www.piacton.com Instructions for Mounting and Operation of Princeton Instruments Model TS-428 250 Watt Tungsten-Halogen Light Source Ver 2.
2 Description: The Princeton Instruments Model TS-428 is a 250 watt tungst en-halog en light source system des igned for use with Acton series spectrom eters.
3 Install ation In structi on s TS-428 and TS-428 -DC Impor tant : These instruction s are valid for TS-428 and TS-428-DC Light Sources b earing certain serial numbers. If the digits of the serial number that imm ediat ely follow 428 are 26 1 or greater pleas e use these instructions.
4 Light Source Installation (With Filter Wheel ) 1) Be sure that th ere are no cable connect ions made t o the TS-428 / TS-4 28-DC Light Source a nd that is has ha d s ufficie nt tim e to cool. 2) Insert the three 8-32 x 1 ¼” blac k alloy screws into the recesse d holes of the ¼” Space r as shown in st ep on e.
5 Step 2. Step 3. Step 4. Tighten the s e Remove Cover Screws.
6 Step 5. Step 6. Light Source Installation (No Fil ter Wheel) Perform all the a bove steps exce pt substitute the ¾” Spacer for the Filter Whee l. ¾” Spacer Mounting (for ser ial numbers fo ll .
7 For proper operation, the lam p housing should be mount ed to the en trance sli t of the spect rometer. The light collectio n mirror, located in the lamp housi ng, is design ed to focu s light fr om the lam p onto th e entrance sl it of the s pectrom eter.
8 the lig ht sourc e mount ing fla nge align properly with the two tappe d hole s al ong the u pper edge of the adapter pla te. 9. Insert the (2) 8- 32 x ½” cap screw s from the plastic ba g in the in ner pair of clear ance holes in the light source mounting flange and tigh ten.
9 Supplemental In structions for TS-428D C Tungsten-Halogen Li ght Source The TS-4 28DC is a 25 0 watt tungste n-halogen light so urc e powere d by an adj ustable regulated DC po wer supply. The la m p is rated fo r 250 watts at 24 volts. Refer to the TS- 428 in structi o n manual f or moun ting the s ource hou sing int o the Acton monoc hrom ator.
15 DISCOVERY WAY ACTON, MA 01720 THIS DRAWING REMAINS THE PROPERTY OF PRINCETON INSTRUMENTS AND CONTAINS PROPRIETARY INFORMATION WHICH SHALL NOT BE REPRODUCED OR DISCLOSED WITHOUT WRITTEN AUTHORIZATION.
An important point after buying a device Princeton TS-428 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Princeton TS-428 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Princeton TS-428 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Princeton TS-428 you will learn all the available features of the product, as well as information on its operation. The information that you get Princeton TS-428 will certainly help you make a decision on the purchase.
If you already are a holder of Princeton TS-428, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Princeton TS-428.
However, one of the most important roles played by the user manual is to help in solving problems with Princeton TS-428. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Princeton TS-428 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
