Instruction/ maintenance manual of the product AUD-S Audi
Go to page of 24
INST ALLA TION AND OWNER’S MANUAL As of date of man ufacture, meets all ANSI/UL 325 Safety Requ irements fo r Vehic ular do or oper ators AUD-S AU SERIES WITH SOLID ST A TE CONTROL CIRCUITR Y DRA WB.
READ THESE STATEMENTS CA R EFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY. The Warning and Caution boxes througho ut th is manual are th ere to protect you and your equipment. Pay close at tention to these boxes as you follow the manual. WARNING Indicates a MECHANICAL haz ard of INJURY OR DEATH.
M O D EL AU D- S OP ER AT O R A P P LI C AT I O N S : Drawbar op erators are for commercial and in dustrial use on secti onal over head do ors whic h use horiz ontal track wi th norm al radi us. A dra w bar opera tor i s not suitab le for do ors with high lift exceed ing 24 inc hes or vert ical lift doors.
Before starting the installation of the operator, the door m ust be in good working condition and properly counterbalanced. Inspect the door and track for loose or m issing hard ware. Test the door manually for balance and ease of op eration. Lubricate door hinges and rollers.
T O REDUCE THE RISK OF SEVERE INJUR Y O R D E A T H : R E AD AN D F O L L O W AL L INST ALLA TION INSTRUCTIONS! WARNING ITEM # PART# DESCRIPTION QUAN. 1 Operat or Po wer Head 1 2 Tra ck Rails 2 7 00 6.
2) After the track is assembled, position track assemb l y onto the operator power head and attach w ith four 3/8”-16 x 1” bolts, lock washers and nuts (supplied in a separate hardw are package #100470). NOTE: To k eep #41 chain (used on 1/2 and 3/4 H.
TO A VOID D A M AGE TO DOOR A ND OPERATOR ENSURE A LL DOOR LOCKS A RE DIS ABLED. USE A N IN TERLOCK SW ITCH IF A LOCK IS REQU IRED TO RE T A IN FUNCTIONA LITY. CA UTION 1) Locate the center of the doo r and mark a line on the wall directly abo ve the door.
4) Mount the front mounting bracket ( Item 9) to the mounting pad as shown in Fig ure 8. The location of the door’s torsion shaft may prevent you from placing the mountin g pad in the location shown. Mount the pad as close as possible to t hree (3) inches above the door’s high arc point.
8) Figure 12 details a ty pical method of hanging the operator from the ceiling. Each installation will vary due to the difference in building structure s; but in all installations side braces should be used to further strengthen the installation. I f the operator track (rail) is lo ng er than 15 feet a m id support is recommended.
TO A VOID DAMAGE TO DOOR A ND OPERA T OR ENSURE A LL DOOR LOCKS A RE DIS ABLED. USE A N INTERL OCK SWITCH IF A LOCK IS REQU IRED TO RE T A IN FUNCTIONA LITY. CA UTION TO PR EVENT THE RISK OF PERSONA L INJU RY AND /OR D A M AGE TO DOOR OR PROPERTY, ONL Y OPERA TE DOOR CONTROL WHEN DOOR IS IN CLEA R V IEW.
Figure 15 OPEN TB1 STOP CLOSE OPEN COM CLOSE STOP NO REV NC REV PHOTO COM SINGLE ILOCK 24 VAC COM SAFE FINISH PHOTOBEAM 3-WIRE PH OTOBEAM MOTOR CONT ROL BOARD Door Edge and P hotoelectric Wiring See text on pa ge 10 for ope ration when S afe-Finish™ or Access Alliance Safe-Fini sh II™ photo- beams are connecte d.
12 NOTE: It is now necessary to turn on the power in order to change the Operatin g Mode (if applicable), progr am any changes de sired to th e operator’s other settings, check for proper performanc.
OPER A TION AND A DJUSTM ENT INSTRUCTIONS 13 IMPORT ANT SA F ETY INSTR UCTIONS FOR OWNER • Understand all of the operating features of y o ur door control sy s tem at the time of its installation. Your installin g dealer will demonstrate them for y ou.
14 OPER A TION AND A DJUSTM ENT INSTRUCTIONS Changing the Switch Selectable Operation Modes The following m o des are selected by setting the on-board dip switches, Figure 20 at right show s where the switches are located on the operator control board.
OPER A TION AND A DJUSTM ENT INSTRUCTIONS 15 TS Operation Open Button : Momentary activation; open override of closing door. Close Button : Momentary activation.
The sole noid operate d brake may require occasi onal adj ustmen t. Adjus tment is necess ary if door tends to drif t downward a fter reaching the open li mit . Foll ow t he inst ructi ons belo w a nd us e Figu r e 2 1 as a gui d e. (1) L oosen shoe a djustin g screw and bottom bracke t arm of solen oid.
remember to use the STOP butt on to stop the door at th e Fu lly Open Positio n. 4) Depress the limit nut retaining pla te (D) so it disengag e s from the slots in the lim it nuts. Turn the OPEN lim it nut (E) on the shaft until it engages the Open Limit Switch (A).
CLUTCH A DJUSTMENT The clutch serves to protect th e door, the electric operator and other equipment from undue stress or damage caused by starting forces and/or an obstruction to the door. It should be set no tighter than is necessary to sm oothl y and consistently move the door throughout its full range of trav el.
Following installation, the operator MUST be tested and respond correctly to all controls as specif ied on the w iri ng diagram. Keep personnel and equipm ent clear of the area beneath the door w hen performing the tests.
575 VOL TS, 3 PHASE SINGLE VOL TAGE MOTOR BL/BLK BL/BLK TO REVERSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Connect ion 3 BLUE (T ,J, H) YELLOW BLUE RED BLACK A.
WIRING DIAGRAM/SCHEMA TIC - THREE PH A SE 21 575 VOL TS, 3 PHASE SINGLE VOL T AGE MOTOR BL/BLK BL/BLK TO REVERSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Connection 3 BLUE (T ,J,H) YELLOW BLUE RED BLACK A.
FIGURE 24 - OPERA TOR DIMENSIONS 107093 OPER A TOR DIMENSIONS / NOTES 22 NOTES.
Ref Part # Descrip tion Assem blies A 106798 Frame Assembly w/Sh afts, AUD (1 /3 HP) 1074 12 Fram e Assembly w/Shafts, A UD (1/2 & 3/ 4 HP) C 11007 5 Clutch Shaf t Assembl y, AUD D 109 848 Driv e .
Manufacturer’s Lim ited Warranty Linear L LC warr ants its All star brand c ommercial door oper ators to be f ree from def ect in ma terial and w orkmanshi p for a peri od of tw o (2) years from the da t e of purch ase. To obtain service contact y our dealer.
An important point after buying a device Audi AUD-S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audi AUD-S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audi AUD-S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audi AUD-S you will learn all the available features of the product, as well as information on its operation. The information that you get Audi AUD-S will certainly help you make a decision on the purchase.
If you already are a holder of Audi AUD-S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audi AUD-S.
However, one of the most important roles played by the user manual is to help in solving problems with Audi AUD-S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audi AUD-S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
