Instruction/ maintenance manual of the product PAR-650 Precision Power
Go to page of 11
P AR–650 5 Band P aragraphic EQ.
INTRODUCTION Thank you f or choosing Precision P ower ™ audio equipment. At Precision P ower ™ we proudly design and engineer the world’ s finest audio products .
● Built-in remote output with tur n-on dela y f or switching on amps . ● 30V MOSFET s witching power supply . ● Gold-plated RCA input/output jacks . ● Half-din chassis f or ease of installation. INST ALLA TION 1. Read this manual carefully and in its entirety before installing this equalizer .
retract with each press. ● IN and OUT P osition - A knob is set to its in position when it is initially e xtended. T o set a knob to its out position pull gently on the knob until a plainly-f elt notched position is reached. NO TE: DO NO T use e xcessiv e force when using the adjustment knobs or damage to their release mechanism can result.
crossov er frequency f or the dedicated subwoof er output between 30–400 Hz at 12dB/octav e. 5. High-P ass Output Frequency Control ● IN/FRONT OUT FREQ UENCY - When in, this knob controls the high-pass crossov er point f or the front outputs between 30 Hz and 400 hz at 12dB/octav e.
5 CONTROL P ANEL REAR P ANEL FEA TURES P ower Connector 1. Remote T urn On Output - This output is intended to be the remote tur n on f or the system amplifiers and has a b uilt-in dela y . T wo to three seconds after the P AR-650 receives a (+)12V turn on signal it will send a (+)12V tur n on signal to the amplifiers.
5. P ower Fuse - This fuse protects the P AR 650 on-board electr ical components. Nev er replace this fuse with one of higher v alue or damage to the P AR 650 could occur and result in loss of your warr anty .
NO TE: If connecting more than one input source to the P AR-650, use the Source 1 gain controls to match the input le vel of both sources . 3. Set the filter gains to the flat (center) setting. 4 Complete all signal and power connections to the P AR-650.
5 . If the front and rear outputs hav e been set to high pass by setting the s witch on the rear panel to the high pass setting, adjust the front crossov er to the low est possible setting with a minimum of distortion. Repeat f or the rear speakers . 6 .
SPECIFICA TIONS PRECISION PO WER P AR-650 Filter P arameters Sub 30-70Hz Mid-bass 125-250Hz Low-mid 400-800Hz Hi-mid 1.5-5kHz Hi 8-20kHz Boost/Cut 18dB/octav e maximum Filter Bandwidth V ar ies with c.
W arranty LIMITED TWO YEAR CONSUMER W ARRANTY : Directed Electronics, Inc. promises to the or iginal purchaser , to replace this product should it prov e to be def ective in workmanship or material un.
An important point after buying a device Precision Power PAR-650 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Precision Power PAR-650 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Precision Power PAR-650 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Precision Power PAR-650 you will learn all the available features of the product, as well as information on its operation. The information that you get Precision Power PAR-650 will certainly help you make a decision on the purchase.
If you already are a holder of Precision Power PAR-650, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Precision Power PAR-650.
However, one of the most important roles played by the user manual is to help in solving problems with Precision Power PAR-650. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Precision Power PAR-650 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
